< prior
Back to Month
Go to Thread
2019-09-30; 11:11:19 EDT
Member Since
2004-01-29
Posts: 1597
Ric, So sorry to hear about your misadventure. In the past GB has been able to provide replacement centerboard caps. I remember at an Annapolis gathering one year one of the attendees walking around with his brand new cap from Stan. I would try to contact him first. Best of luck, Mary LouSee the original archive post
On 9/30/2019 10:44 AM, Richard Stott wrote: > Boy do I have a gasket/cap project! > The attached photo shows what can happen when the boat is launched with the Center Board line not cleated. > Here is the story - and I’m sticking to it. > I have had my ’84 Continental since I inherited it from my dad who bought it used in ’89. > I have re-bult most of the interior and I use the boat a lot. > For 6 years I’ve had it hauled and lunched professionally back and forth to my driveway. > This year I finally completed that trailer rebuild project and hauled it for the first time on the rebuilt trailer. > Everything went smoothly until the boat was out and I was not happy with the balance on the trailer. > I decided to re-lauch and move the boat further toward the trailer tongue. > While the boat was out, I asked my helper to release the ‘red’ line on the bulkhead - I was going to begin de-rigging and roll up the jib fuller, but got distracted with the boat position. . > I meant the jib fuller, but my helper ( good sailer, but not familiar with the boat) released the CB cleat (also red) which I didn’t realize. > When we relaunched, the boat slid nicely off the trailer and into the shallow water at the ramp. > The CB deployed as the boat was moving backward - and hit the shallow bottom. > > Before we realized what happened, we had the boat back on the trailer. > Something was odd, but I didn’t know what. > When we pulled it the 2nd time, the trailer tires looked flat and the trailer seemed even more unbalanced - it was also pouring water from the boat. > I climbed on and discovered the CB popping through the CB trunk cap and water had filled the boat to the a few inches over the cabin sole floor. > We had managed to ‘sink’ Dadventure, right on its new trailer. > Flooded the pull-out storage box, my tool box, multi-meter and lots of stuff that doesn’t like to be wet. > It broke the 3/4” plywood sole cover in the process, which is an easy fix - the cap - not so much. > What a mess! > > I was considering replacing my original CB with a Diamond Board - maybe now is the time. > Can anyone explain the pros/cons of such a change? > Can I get a new cap from Stan or do I have to rebuild one myself? > > I can tell you with certainty that the same thing will never happen again, but this is a major repair that I didn’t expect. > Ric > sv Dadventure > > Richard Stott, AIA, LEED AP > www.stottarchitecture.com > Office 631-283-1777 > Cell 516-965-3164 > > > > > >> On Sep 30, 2019, at 9:56 AM, Mitch Mitchell <mitchpadl at gmail.com> wrote: >> >> Wow! Thanks for the info. Sounds like that was quite a project. Hopefully >> all I will need to do is replace the gasket. I like the idea of bolts and >> washers. >> >> On Mon, Sep 30, 2019 at 12:18 AM Graham Stewart <gstewart8 at cogeco.ca> wrote: >> >>> Mitch: >>> >>> Replacing the gasket is not difficult but is a major PITA. Any >>> reconstruction of the cap or flange is also a possibility and adds to the >>> pain. Good idea to check it out in the water before you take it all apart. >>> >>> Eventually, however, it will probably be necessary to do this job if for >>> no other reason than to replace the line and pulleys. >>> On my boat the removal of the cap was made infinitely worse by virtue of >>> the fact that some previous owner used 5200 sealant and then put fiberglass >>> over the top of the cap. As a result I broke the cap in two pieces getting >>> it off and damaged the housing flange with large gouges. Hopefully you will >>> not face that issue. No one else has reported a similar problem on this >>> list that I have seen. >>> >>> I would replace the screws with stainless steel bolts and use large fender >>> washers and lock washers.I think it is better to punch clean holes in the >>> gasket rather than drilling them. >>> >>> I did not think I had access to the proper gasket material and substituted >>> other neoprene material that I thought would work. As a result I could not >>> get a perfect seal without using a sealant. I chose to use butyl tape as it >>> makes an excellent seal but has very low adhesive properties and so is easy >>> to remove when the time comes. Butyl is not rated for underwater use but so >>> far has worked well for me in fresh water. Better to get the proper gasket >>> material. >>> >>> BTW, I was able to remove the cap and the centerboard while the boat was >>> on its trailer and have not heard of others needing to raise the boat for >>> that purpose but keep in mind that there appears to be a lot of variation >>> in the construction of the boat over the years and what works for one >>> person might not work in another situation. My boat is a 1976 model so it >>> has the older version of the centerboard. However, I would try to do the >>> work while on the trailer first and raise the boat only if that becomes >>> necessary. >>> >>> While removing the centerboard and fixing the enclosure cap and flange >>> could be done while on the trailer, I discovered that I had serious damage >>> to the bottom of the keel housing with a large crack that went almost >>> entirely around the housing slot. So in the end I had to build a huge lift >>> so that I could work under the keel. My lift was a major project in itself >>> and probably overkill as I later learned that one person was able to >>> support the stern of the boat on a picnic table and support the front with >>> some sort of sawhorse arrangement. So there are definitely easier ways to >>> do this than what I did. The advantage of the lift is that I can raise the >>> boat high enough (5' between the bottom of the keel and the ground) to work >>> more comfortably under the keel and can also use it for my other two boats. >>> However, it is a very large structure. I can send pictures of the lift if >>> anyone is interested. >>> >>> >>> Graham Stewart >>> Agile 1976 Rhodes 22 >>> Kingston Ontario >>> >>> >>> >>> -----Original Message----- >>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >>> Of Mitch Mitchell >>> Sent: Sunday, September 29, 2019 10:34 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] Replacing Centerboard Gasket >>> >>> Thanks JP! Did you have to lower the centerboard to replace the gasket? If >>> that' the case then I would have to get the boat off of the trailer. The >>> screws in the cap look good (not rusty) but there are no washers. I haven't >>> removed the top cap yet but thought I would put the boat in the water once >>> more with the floorboard out so I could see if it was leaking. MM >>> >>> On Sun, Sep 29, 2019 at 7:14 PM JP Dempsey <joedempsey at hughes.net> wrote: >>> >>>> Mitch, I had the same problem last year and finally determined that the >>>> centerboard gasket was the problem. They dry rot eventually. It is a >>>> "fairly" simple job that I ended up doing myself, but you'll have to >>>> purchase a new gasket. I would have purchased from Stan but the >>> centerboard >>>> trunk cover was cracked and needed repair that I was not willing to >>>> attempt. >>>> Also you want to be sure that you drill holes that will match the >>> existing >>>> holes in you CB trunk flange and cover. I have a large collection of >>> photos >>>> that I took during the process. Removal of the trunk cover begins with >>>> removing the port berth/settee and the supporting structure in front of >>> the >>>> companionway. You'll need to remove the center section of the floorboard >>>> (sole) that runs from the inspection hatch back to beneath the >>>> companionway. >>>> (I removed all of the floorboards and found that they were severely >>> molded. >>>> These I replaced with new marine plywood treated with wood preservative >>> and >>>> multiple coats of urethane marine varnish.) You will need to lower the >>> CB. >>>> I >>>> placed a block of wood underneath. Also you'll have to remove the painter >>>> tube between the companionway and the CB cover. If there is any rust on >>> the >>>> machine screws, replace them. McMaster-Carr is the best source. Use only >>>> 316 >>>> grade stainless steel. Also if your CB gasket is not fastened using >>> fender >>>> washers (mine wasn't) get them for both above and below the flange. I did >>>> all of this work while on the trailer during the off season. I believe >>> its >>>> also wise to re-seat all of the port lites and if you ever replace the >>> rub >>>> rail, re-caulk the topside/hull joint with 4200 Sealant. I'm attaching >>>> photos that I hope will help. >>>> < >>>> >>> http://rhodes-22.1065344.n5.nabble.com/file/t752/Cabin_Sole_Original_Sub_Floor_Before.jpg >>>> >>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/CB_Cover_w_Pump.jpg> >>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/CB_Gasket.jpg> >>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/Bilge_2_After.jpg> >>>> >>>> >>>> >>>> >>>> >>>> >>>> ----- >>>> JP Dempsey >>>> s/v Respite >>>> Rhodes 22 1989/2005 >>>> Marshall,VA >>>> -- >>>> Sent from: http://rhodes-22.1065344.n5.nabble.com/ >>>> >>> > --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 