< prior
Back to Month
Go to Thread
2019-09-30; 11:22:04 EDT
Member Since
2013-07-01
Posts: 437
Thanks Mary Lou! I’ll ring ‘im up. Richard Stott, AIA, LEED AP www.stottarchitecture.com Office 631-283-1777 Cell 516-965-3164See the original archive post
> On Sep 30, 2019, at 11:11 AM, Mary Lou Troy <mtroy at atlanticbb.net> wrote: > > Ric, > So sorry to hear about your misadventure. In the past GB has been able to provide replacement centerboard caps. I remember at an Annapolis gathering one year one of the attendees walking around with his brand new cap from Stan. I would try to contact him first. > Best of luck, > Mary Lou > > On 9/30/2019 10:44 AM, Richard Stott wrote: >> Boy do I have a gasket/cap project! >> The attached photo shows what can happen when the boat is launched with the Center Board line not cleated. >> Here is the story - and I’m sticking to it. >> I have had my ’84 Continental since I inherited it from my dad who bought it used in ’89. >> I have re-bult most of the interior and I use the boat a lot. >> For 6 years I’ve had it hauled and lunched professionally back and forth to my driveway. >> This year I finally completed that trailer rebuild project and hauled it for the first time on the rebuilt trailer. >> Everything went smoothly until the boat was out and I was not happy with the balance on the trailer. >> I decided to re-lauch and move the boat further toward the trailer tongue. >> While the boat was out, I asked my helper to release the ‘red’ line on the bulkhead - I was going to begin de-rigging and roll up the jib fuller, but got distracted with the boat position. . >> I meant the jib fuller, but my helper ( good sailer, but not familiar with the boat) released the CB cleat (also red) which I didn’t realize. >> When we relaunched, the boat slid nicely off the trailer and into the shallow water at the ramp. >> The CB deployed as the boat was moving backward - and hit the shallow bottom. >> >> Before we realized what happened, we had the boat back on the trailer. >> Something was odd, but I didn’t know what. >> When we pulled it the 2nd time, the trailer tires looked flat and the trailer seemed even more unbalanced - it was also pouring water from the boat. >> I climbed on and discovered the CB popping through the CB trunk cap and water had filled the boat to the a few inches over the cabin sole floor. >> We had managed to ‘sink’ Dadventure, right on its new trailer. >> Flooded the pull-out storage box, my tool box, multi-meter and lots of stuff that doesn’t like to be wet. >> It broke the 3/4” plywood sole cover in the process, which is an easy fix - the cap - not so much. >> What a mess! >> >> I was considering replacing my original CB with a Diamond Board - maybe now is the time. >> Can anyone explain the pros/cons of such a change? >> Can I get a new cap from Stan or do I have to rebuild one myself? >> >> I can tell you with certainty that the same thing will never happen again, but this is a major repair that I didn’t expect. >> Ric >> sv Dadventure >> >> Richard Stott, AIA, LEED AP >> www.stottarchitecture.com >> Office 631-283-1777 >> Cell 516-965-3164 >> >> >> >> >> >>> On Sep 30, 2019, at 9:56 AM, Mitch Mitchell <mitchpadl at gmail.com> wrote: >>> >>> Wow! Thanks for the info. Sounds like that was quite a project. Hopefully >>> all I will need to do is replace the gasket. I like the idea of bolts and >>> washers. >>> >>> On Mon, Sep 30, 2019 at 12:18 AM Graham Stewart <gstewart8 at cogeco.ca> wrote: >>> >>>> Mitch: >>>> >>>> Replacing the gasket is not difficult but is a major PITA. Any >>>> reconstruction of the cap or flange is also a possibility and adds to the >>>> pain. Good idea to check it out in the water before you take it all apart. >>>> >>>> Eventually, however, it will probably be necessary to do this job if for >>>> no other reason than to replace the line and pulleys. >>>> On my boat the removal of the cap was made infinitely worse by virtue of >>>> the fact that some previous owner used 5200 sealant and then put fiberglass >>>> over the top of the cap. As a result I broke the cap in two pieces getting >>>> it off and damaged the housing flange with large gouges. Hopefully you will >>>> not face that issue. No one else has reported a similar problem on this >>>> list that I have seen. >>>> >>>> I would replace the screws with stainless steel bolts and use large fender >>>> washers and lock washers.I think it is better to punch clean holes in the >>>> gasket rather than drilling them. >>>> >>>> I did not think I had access to the proper gasket material and substituted >>>> other neoprene material that I thought would work. As a result I could not >>>> get a perfect seal without using a sealant. I chose to use butyl tape as it >>>> makes an excellent seal but has very low adhesive properties and so is easy >>>> to remove when the time comes. Butyl is not rated for underwater use but so >>>> far has worked well for me in fresh water. Better to get the proper gasket >>>> material. >>>> >>>> BTW, I was able to remove the cap and the centerboard while the boat was >>>> on its trailer and have not heard of others needing to raise the boat for >>>> that purpose but keep in mind that there appears to be a lot of variation >>>> in the construction of the boat over the years and what works for one >>>> person might not work in another situation. My boat is a 1976 model so it >>>> has the older version of the centerboard. However, I would try to do the >>>> work while on the trailer first and raise the boat only if that becomes >>>> necessary. >>>> >>>> While removing the centerboard and fixing the enclosure cap and flange >>>> could be done while on the trailer, I discovered that I had serious damage >>>> to the bottom of the keel housing with a large crack that went almost >>>> entirely around the housing slot. So in the end I had to build a huge lift >>>> so that I could work under the keel. My lift was a major project in itself >>>> and probably overkill as I later learned that one person was able to >>>> support the stern of the boat on a picnic table and support the front with >>>> some sort of sawhorse arrangement. So there are definitely easier ways to >>>> do this than what I did. The advantage of the lift is that I can raise the >>>> boat high enough (5' between the bottom of the keel and the ground) to work >>>> more comfortably under the keel and can also use it for my other two boats. >>>> However, it is a very large structure. I can send pictures of the lift if >>>> anyone is interested. >>>> >>>> >>>> Graham Stewart >>>> Agile 1976 Rhodes 22 >>>> Kingston Ontario >>>> >>>> >>>> >>>> -----Original Message----- >>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >>>> Of Mitch Mitchell >>>> Sent: Sunday, September 29, 2019 10:34 PM >>>> To: The Rhodes 22 Email List >>>> Subject: Re: [Rhodes22-list] Replacing Centerboard Gasket >>>> >>>> Thanks JP! Did you have to lower the centerboard to replace the gasket? If >>>> that' the case then I would have to get the boat off of the trailer. The >>>> screws in the cap look good (not rusty) but there are no washers. I haven't >>>> removed the top cap yet but thought I would put the boat in the water once >>>> more with the floorboard out so I could see if it was leaking. MM >>>> >>>> On Sun, Sep 29, 2019 at 7:14 PM JP Dempsey <joedempsey at hughes.net> wrote: >>>> >>>>> Mitch, I had the same problem last year and finally determined that the >>>>> centerboard gasket was the problem. They dry rot eventually. It is a >>>>> "fairly" simple job that I ended up doing myself, but you'll have to >>>>> purchase a new gasket. I would have purchased from Stan but the >>>> centerboard >>>>> trunk cover was cracked and needed repair that I was not willing to >>>>> attempt. >>>>> Also you want to be sure that you drill holes that will match the >>>> existing >>>>> holes in you CB trunk flange and cover. I have a large collection of >>>> photos >>>>> that I took during the process. Removal of the trunk cover begins with >>>>> removing the port berth/settee and the supporting structure in front of >>>> the >>>>> companionway. You'll need to remove the center section of the floorboard >>>>> (sole) that runs from the inspection hatch back to beneath the >>>>> companionway. >>>>> (I removed all of the floorboards and found that they were severely >>>> molded. >>>>> These I replaced with new marine plywood treated with wood preservative >>>> and >>>>> multiple coats of urethane marine varnish.) You will need to lower the >>>> CB. >>>>> I >>>>> placed a block of wood underneath. Also you'll have to remove the painter >>>>> tube between the companionway and the CB cover. If there is any rust on >>>> the >>>>> machine screws, replace them. McMaster-Carr is the best source. Use only >>>>> 316 >>>>> grade stainless steel. Also if your CB gasket is not fastened using >>>> fender >>>>> washers (mine wasn't) get them for both above and below the flange. I did >>>>> all of this work while on the trailer during the off season. I believe >>>> its >>>>> also wise to re-seat all of the port lites and if you ever replace the >>>> rub >>>>> rail, re-caulk the topside/hull joint with 4200 Sealant. I'm attaching >>>>> photos that I hope will help. >>>>> < >>>>> >>>> http://rhodes-22.1065344.n5.nabble.com/file/t752/Cabin_Sole_Original_Sub_Floor_Before.jpg >>>>> >>>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/CB_Cover_w_Pump.jpg> >>>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/CB_Gasket.jpg> >>>>> <http://rhodes-22.1065344.n5.nabble.com/file/t752/Bilge_2_After.jpg> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> ----- >>>>> JP Dempsey >>>>> s/v Respite >>>>> Rhodes 22 1989/2005 >>>>> Marshall,VA >>>>> -- >>>>> Sent from: http://rhodes-22.1065344.n5.nabble.com/ >>>>> >>>> >> > > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 