< prior
Back to Month
Go to Thread
2020-05-24; 21:15:26 EDT
Member Since
2018-09-18
Posts: 52
I’ll check those...Thanks again for the help Mary Lou.See the original archive post
On Sun, May 24, 2020 at 9:05 PM Mary Lou Troy <mtroy at atlanticbb.net> wrote: > Olivier, I think you are right about that laminate being glassed on - at > least that is what I vaguely remember thinking it looked like at the > time to us. > > While it's possible that your wet bilge is from the centerboard cap, > it's more likely from a port or the wire connections at the mast step or > some other something that needs to be rebedded. I do remember thinking > at the time that the surface was slick for the gasket but we never had > any suggestion of a leak from there. > > In any event, good luck with your repairs and thank goodness there was > no damage from the sideswipe. > > Mary Lou > > On 5/24/2020 8:34 PM, Olivier Hecht wrote: > > Hi Stan! It almost looked like that extra piece was glassed in...if not > > than definitely glued down well. I think I’d damage the hull interface > just > > by removing it. I’m thinking about just enlarging the inner opening with > a > > keyhole saw to allow me to pull the board. I don’t think the slick > surface > > on the laminate gives the gasket the best matings surface either...that > > might explain my slightly wet bilge. Do you sell new diamond boards, or > is > > it usually more economical to have them repaired locally? > > > > On Sun, May 24, 2020 at 8:17 PM stan <stan at generalboats.com> wrote: > > > >> Mary Lou, > >> > >> since this is between me and you I am happy to join in to report what my > >> now occasionally lying eyes are seeing. > >> > >> A prior owner, as is usually the case when someone reports on a > >> ridiculous design fault attributed to GB, sacrificed access to the cb in > >> the cb trunk in favor of a quick improper fix. > >> > >> The only recourse now for removing the cb is to take off the white > >> whatever it is, throw it away. lift out the cb. Fix what has to be > >> fixed. AND THEN REASSEMBLE THE ENTIRE CB SYSTEM AS GOD AND GB DESIGNED > >> IT TO BE. > >> > >> > >> On 5/24/20 7:17 PM, Mary Lou Troy wrote: > >>> Hi Olivier, > >>> > >>> The laminate is not standard R22 construction. > >>> > >>> At one point we were going to do something to the board, I forget > >>> what, maybe replace the pennant or get rid of the pully in the raising > >>> system and had ordered a new gasket from Stan. When we got it apart > >>> and discovered the laminate, we abandoned the project. We asked Stan > >>> about it and via email he basically shrugged his shoulders and said > >>> something to the effect that "that wasn't our repair." It wasn't > >>> leaking, we found another way to do what we were going to do and > >>> forgot about it. In fact I didn't realize I still had the exchange > >>> with Stan in an old email program until now. > >>> > >>> After a bit of back and forth on a photo, Stan's exact words on the > >>> subject from 2003 were: > >>> > >>> "So what I am seeing is a fiberglass "washer" between the top lip of > >>> the trunk and > >>> neoprene gasket. The question then is was there any leakage between > >>> the fiberglass > >>> gasket and the cb trunk lip? If no then I would leave it in place and > >>> just use a > >>> jib saw to cut on opening in it to match the opening in the cb trunk - > >>> it should > >>> cut easily since it is probably not very thick If on the other hand > >>> there was > >>> leakage between this element and the cb trunk cap I would do whatever > >>> is necessary > >>> to pull it off and throw it away and sand smooth the top of the trunk > >>> lip to > >>> receive the neoprene gasket." > >>> > >>> As I noted above, it wasn't leaking so my recollection is we decided > >>> not to mess with it. > >>> > >>> Sorry this isn't more help. > >>> > >>> Mary Lou > >>> > >>> > >>> On 5/24/2020 6:12 PM, Olivier Hecht wrote: > >>>> My last message with two pics bounced back...hopefully this goes > >>>> through... > >>>> > >>>> Whoops...sorry. Forgot to attach it! Here they are. That white piece > is > >>>> glued to the boat...I’m sure of it. > >>>> > >>>> > >>>> On Sun, May 24, 2020 at 6:02 PM Richard Beytagh <rbeytagh at gmail.com> > >>>> wrote: > >>>> > >>>>> The pic didn’t come through? > >>>>> > >>>>> On Sun, May 24, 2020 at 5:58 PM Olivier Hecht <oehecht at gmail.com> > >>>>> wrote: > >>>>> > >>>>>> Well the board fell onto the trailer axle since I guess I pulled > >>>>>> the boat > >>>>>> too far forward. Took a chunk out of it so I decided to try to pull > >>>>>> it. I > >>>>>> just got the cap off after removing ~60 10mm bolts with blind nuts > and > >>>>> now > >>>>>> I can’t access the pivot to remove the board. See pics...the white > >>>>>> piece > >>>>> of > >>>>>> laminate? seems to be glasses into the hull. I’m afraid to destroy > >>>>>> it by > >>>>>> prying. Can anyone confirm to me that this piece should be > >>>>>> removable? I > >>>>>> cants see any other way to lift the board out since the pivot is > >>>>>> inaccessible. I’ll be at the boat for an hour more max, then I have > to > >>>>> head > >>>>>> home. Was really hoping to take the board with me! > >>>>>> > >>>>> -- > >>>>> > >>>>> > >>>>> ~~~ _/) ~~~ > >>>>> > >>>>> Richard Beytagh > >>>>> Phone: 828 337 0180 > >>>>> > >>>> -------------- next part -------------- > >>>> A non-text attachment was scrubbed... > >>>> Name: IMG_3661.jpg > >>>> Type: image/jpg > >>>> Size: 2852710 bytes > >>>> Desc: not available > >>>> URL: > >>>> < > >> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200524/1a8b1c27/attachment.jpg > >>> > >>> > >> > > > -- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 