< prior
Back to Month
Go to Thread
2020-05-26; 00:36:05 EDT
Member Since
2004-04-05
Posts: 2060
Wow what a story, and an informative narration. Thanks! Chris Geankoplis EnosisSee the original archive post
On Mon, 25 May 2020 at 11:12, Ric Stott <ric at stottarchitecture.com> wrote: > HI folks > It’s been awhile since promised to provide a “What not to do” story. > Last September, I hauled the boat early because we had planned a last > minute trip to see my son and family in Ireland. > I hauled the boat on my own trailer for the first time. I bought the > tailor from a fellow Rhodie 5 or 6 years ago as a project, and finally got > it done enough to use it. Prior to that, I had a commercial hauler come and > pick up/deliver the boat from my driveway to the ramp about 2 miles away. > So I asked a sailer friend of mine to help. We got the boat onto the > trailer and I was about to go through the mast lowering, when I decided > the boat was too far back and needed to be moved about 6 inches forward. > The best way was to re-launch. Before we relaunched and when I was about to > work on the jib furler, I asked Joe to release the ‘red’ line in the > cockpit, meaning the jib furler line. But the Center board line is also > red, and that’s what he released. We both got distracted at that point and > decided to relaunch. > > When the boat came off the trailer, the old style (Blade) CB was loose > and rolled off the trailer into the full down position. > The water at the ramp was not deep, so the CB hit the bottom with 3000 > pounds of boat and added force of momentum. > Although I didn’t know it, as the CB hit bottom, it easily poked through > the CB cap, broke out the floor boards and damaged the cabin console, > electrical panel and wiring. The boat “sunk” immediately onto the trailer > bunks and I couldn’t move it forward any further, but I still didn’t know > why yet. When we pulled the boat out, water was pouring from underneath and > the tires looked almost flat. (There was and extra 3000 pounds of water in > the boat) I still didn’t know what was happening. I was curious where all > the water was coming from and climbed into the boat to see. Then my heart > sunk too. The boat was still full of water over the floor boards. > Everything below the galley shelf level was underwater, the slide out tray, > tool box, parts boxes, spare parts, you name it. > > When we tried to crank the boat further onto the trailer after the > relaunch, the winch pulled the Bow ring about 3/4” out from the bow. This > spring, when I finally crawled into the bow to inspect it, I found two > rusted steel nuts on the stainless bow ring. The mahogany block was > rotted. I tried for a few weeks spraying Marvil Mystery Oil on them every > few days to no avail and then finally cut them off with a Dremel tool - > pretty tight quarters up there for a big guy like me. > > We left the day after the bad haul, for Ireland and while away, my > father-in-law went into the hospital, which began a chain of events that > ended in his passing on March 12th. I never even thought to call the > insurance company, I just thought of how I was going to fix it, knowing > that most likely, nobody else could. > > "STAN TO THE RESCUE” at some point before the holidays, I contacted Stan, > the man who held the secrete to my repair. Indeed, he said, he could > replace the Center Board Cap for me. I signed up for the ROC program, sent > Stan a check and waited. With some prodding, I received my newly molded CB > cap some time in Early April with a nice email suggesting how to re-rig the > control line straight from the trailing edge of the blade up through the > thru-hull (which I had to install myself) to the cleat. I mocked this > arrangement up and decided I did like the control line hanging below the > trunk while underway. So, I removed the SS turning post from the old cap, > ordered new blocks for the trailing edge of the CB from England, and new > micro-books for the inside top of the cap from Defender. With some careful > milling, I got the new parts installed into the CAP and began to scratch my > head about how to drill over 50 holes that line up with the old ones. > > CRANE: > I had to remove the trailer from under the boat to work on the CB. I had > seen other systems, but needed a way to do it by myself. I built the crane > shown n the pics from 5/4 x 6 ACQ limber and a 4 x 8 beam I had by chance, > and some 3/8” plywood for stiffness. I used a 3 ton come-along. After the > Bow ring repair, I connected it directly to the Bow ring, but when I > removed the trailer I made a sling a couple of feet back from the bow. > I can assemble and dis-assemble the crane single handed > > CB CAP Attachments: > Stan suggested I epoxy the old holes and drill new ones. I thought I > could transfer the hole locations by laying the new cap on the trunk and > marking holes with a short pencil or sharpie - that idea didn’t work. My > second idea was to spray paint the holes one I had the cap clamped down - > that didn’t work either - I would have sprayed everything but what I > needed. > > I finally made a template of the existing holes using some thick > translucent paper, which worked beautifully. I taped the paper over the > flanges of the trunk, poked the holes with an ice pick, the taped the same > paper onto the cap and drilled the holes where the ice pic holes were. > > My ’84 original CB cap was screwed down with 3/16” sheet metal screws. I > think I could have re-used those as it never leaked and was easy to do, but > the consensus is to use machine screws, so I drilled out all the holes to > 1/4” and used the SS Bolts and lock nuts and washers that Stan supplied > with the Cap. > > I bought marine grade plywood to rebuild the floor boards and I had to > replace the electrical panel for more than one reason. > Covid isolation gave me the time I needed to do all this work. I think > the electrical work took the longest. > > So it's all back together and I’m almost ready to launch. I’m confident > that it will not leak and have the boat mostly put back together. I’ll let > you know how it goes. > Here are some pics of the whole process. > I used the Subaru, which I just turned in from my lease yesterday, to > pull the boat out from under the oak tree, so that I can keep it clean and > work on the new 'single handed mast raising system'. I never used the > Cross-trek to tow the Rhodes as it is only rated for 1500 lbs., but it > probably could have been used to launch - only 2 miles away. I’ll let you > know how the SHMRS works. > > All-in-all, it was not an easy job, but not particularly hard either - > just time consuming. > Launch could be within days. > Ric > Dadventure > Hampton Bays > > > > > > > The new and the old cap together > > New blocks installed > > Clean up and Bilge Paint (Inspired by “DaList”) > > > > New Cap with New rigging added > > The Crane > > > Richard Stott, AIA, LEED AP > www.stottarchitecture.com > Office 631-283-1777 > Cell 516-965-3164 > > > > > > > On May 25, 2020, at 6:53 AM, Olivier Hecht <oehecht at gmail.com> wrote: > > > > Does anyone know the axle diameter on the Triad trailer? I’m back home > ~70 > > miles from my boat and trying to gather supplies to continue the > > diamondboard removal/repair effort and also try to prevent future damage > if > > I ever get the boat too far forward on the trailer again. This picture is > > what happened the first time the board fell onto the axle...I was amazed > > how cleanly the axle cut into it. Yesterday it got much worse as the > board > > started to split and also got caught on the cross-member when I refloated > > the boat to try to reposition her in the trailer. I’m thinking of adding > > one of these rollers using large u-bolts or maybe just some good padding > as > > a safety feature in case this happens again after I repair the board. > > Thanks in advance. > > > > > https://www.easternmarine.com/5-v-keel-amber-roller-bracket-assembly-86279-0 > > -------------- next part -------------- > > A non-text attachment was scrubbed... > > Name: C323D8B0-7D7E-4D3D-9126-19D1F1F3912C.jpeg > > Type: image/jpeg > > Size: 2635797 bytes > > Desc: not available > > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200525/66d77282/attachment.jpeg > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 