< prior
Back to Month
Go to Thread
2020-06-02; 07:09:23 EDT
Member Since
2013-07-01
Posts: 437
I often have trouble attaching pics. I made them very low Rez first but whatever. I think the hose pieces I used were 5/8” diameter. Don’t slice them just cut to the same length as the depth of the tapered slot. Simple! Ric Sent from my iPhoneSee the original archive post
> On Jun 2, 2020, at 6:02 AM, Olivier Hecht <oehecht at gmail.com> wrote: > > ?Thanks Graham. > >> On Tue, Jun 2, 2020 at 12:02 AM Graham Stewart <gstewart8 at cogeco.ca> wrote: >> >> The pieces of hose should be long enough to fill the slot between the >> centerboard pin and the cap. Use regular hose that is relatively soft and >> flexible as one of the purposes of the pieces is to absorb the shock should >> the centerboard be forced up. >> >> Graham Stewart >> gstewart8 at cogeco.ca >> >> >> -----Original Message----- >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >> Of Olivier Hecht >> Sent: Monday, June 1, 2020 6:53 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Emergency diamondboard help...at boatyard for >> only a little while longer >> >> Richard, I didn’t see the picture come through. Are the hose pieces >> “intact”, meaning I cut a few inches off of a hose but don’t have to split >> it lengthwise or do anything else like that? >> >> On Mon, Jun 1, 2020 at 5:19 PM Michael D. Weisner <mweisner at ebsmed.com> >> wrote: >> >>> Ric, >>> >>> I love the phrase " when the CB entered the cabin." >>> >>> Mike >>> s/v Wind Lass ('91) >>> Nissequogue River, NY >>> I’d rather be sailing :~) >>> >>> >>> -----Original Message----- >>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of >>> Richard Stott >>> Sent: Monday, June 1, 2020 4:40 PM >>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>> Subject: Re: [Rhodes22-list] Emergency diamondboard help...at boatyard >> for >>> only a little while longer >>> >>> HI Todd >>> I don’t have a Diamond board, I have the old style CB. >>> Here are some pics of how it is rigged including the hose pieces. >>> They can be anything, but do not make the diameter too big or they will >>> impede the smoothness of the CB operation (on the old stye ) They do help >>> quiet the banging noise, but they do not prevent it. >>> I‘ve taken my CB part 3 times now for various reasons. >>> I don’t want to do that any more. >>> Most recently, I installed a new cap after I destroyed the previous one >>> when the CB entered the cabin. >>> Boating is a sure bet that something will happen the you never, ever >>> expected. >>> More on that coming soon. >>> Ric >>> Dadventure >>> >>> >>> Richard Stott, AIA, LEED AP >>> www.stottarchitecture.com >>> Office 631-283-1777 >>> Cell 516-965-3164 >>> >>> >>> >>> >>> >>>> On Jun 1, 2020, at 7:01 AM, Todd Tavares <tavares0947 at gmail.com> >> wrote: >>>> >>>> Someone will surely post pictures, but they drop down into the slots on >>>> either side of the centerboard, on top of the pin. >>>> >>>> Todd T. >>>> >>>> tavares0947 at gmail.com >>>> >>>> On Mon, Jun 1, 2020, 6:13 AM Olivier Hecht <oehecht at gmail.com> wrote: >>>> >>>>> Anyone have pictures of how the “scrap hose pieces” fit around the >>>>> diamondboard? >>>>> >>>>> On Sat, May 30, 2020 at 2:19 PM Olivier Hecht <oehecht at gmail.com> >>> wrote: >>>>> >>>>>> I was also not shocked to not find the “two scraps of garden hose” >> I’ve >>>>>> heard so much about. I think they dampen noise and movement near the >>>>> pivot >>>>>> of the board, and my board does “rattle” while sailing whenever it’s >>> not >>>>>> fully loaded. Does anyone have pictures of how/where those pieces of >>> hose >>>>>> should go when I reassemble everything? Thanks again! >>>>>> >>>>>> On Sat, May 30, 2020 at 11:51 AM Olivier Hecht <oehecht at gmail.com> >>>>> wrote: >>>>>> >>>>>>> Got the board pulled today and the local yard should be able to >> repair >>>>> it >>>>>>> this week. Here is a picture in case anyone is curious about the >>> layers >>>>> of >>>>>>> construction. >>>>>>> >>>>>>> >>>>>>> >>>>>>> On Mon, May 25, 2020 at 12:00 PM Olivier Hecht <oehecht at gmail.com> >>>>> wrote: >>>>>>> >>>>>>>> Thanks Stan. I already have two of those three upgrades and love >> them >>>>>>>> but have been thinking about a new tiller at some point! >>>>>>>> >>>>>>>> On Mon, May 25, 2020 at 11:02 AM stan <stan at generalboats.com> >> wrote: >>>>>>>> >>>>>>>>> >>>>>>>>> Oliver, >>>>>>>>> >>>>>>>>> www.rhodes22parts.com has parts for the Rhodes that are not >>> available >>>>>>>>> from marine suppliers. In the case of your diamond board however >> I >>> do >>>>>>>>> think that it would be less costly if you have your current one >>>>>>>>> repaired >>>>>>>>> locally. Freight alone for a centerboard can be an item. With >> all >>>>>>>>> that >>>>>>>>> saving how about a new style outhaul car or a fabulous fiberglass >>>>>>>>> tiller >>>>>>>>> or the new invention traveler system. >>>>>>>>> >>>>>>>>> While you got me to my keyboard, a comment. Every action has an >>> equal >>>>>>>>> and opposite reaction. Every recycled and new Rhodes has a yoke >> that >>>>>>>>> prevents the genoa line from leaving its drum so the energy needed >>> to >>>>>>>>> pull out the sail is not altered. From a 94 year old perspective >>>>> every >>>>>>>>> ounce is an item. For you young bucks the extra force needed to >>> pull >>>>>>>>> out the genoa with either Mikes or Rogers ingenious tension >>> techniques >>>>>>>>> would hardly be measurable so a small price to pay. Besides who >>> sails >>>>>>>>> at 94. >>>>>>>>> >>>>>>>>> And Don, if you are listening, I have no recollection of your >>>>> inquiring >>>>>>>>> about a rub rail insert replacement. We have those in stock for >>> Boston >>>>>>>>> Whaler owners since their boats came with red and we are the only >>> ones >>>>>>>>> who also have that color. But the reflective tape idea sound >>>>>>>>> interesting? >>>>>>>>> >>>>>>>>> On 5/24/20 8:34 PM, Olivier Hecht wrote: >>>>>>>>>> Hi Stan! It almost looked like that extra piece was glassed >>> in...if >>>>>>>>> not >>>>>>>>>> than definitely glued down well. I think I’d damage the hull >>>>>>>>> interface just >>>>>>>>>> by removing it. I’m thinking about just enlarging the inner >> opening >>>>>>>>> with a >>>>>>>>>> keyhole saw to allow me to pull the board. I don’t think the >> slick >>>>>>>>> surface >>>>>>>>>> on the laminate gives the gasket the best matings surface >>>>>>>>> either...that >>>>>>>>>> might explain my slightly wet bilge. Do you sell new diamond >>> boards, >>>>>>>>> or is >>>>>>>>>> it usually more economical to have them repaired locally? >>>>>>>>>> >>>>>>>>>> On Sun, May 24, 2020 at 8:17 PM stan <stan at generalboats.com> >>> wrote: >>>>>>>>>> >>>>>>>>>>> Mary Lou, >>>>>>>>>>> >>>>>>>>>>> since this is between me and you I am happy to join in to report >>>>>>>>> what my >>>>>>>>>>> now occasionally lying eyes are seeing. >>>>>>>>>>> >>>>>>>>>>> A prior owner, as is usually the case when someone reports on a >>>>>>>>>>> ridiculous design fault attributed to GB, sacrificed access to >> the >>>>>>>>> cb in >>>>>>>>>>> the cb trunk in favor of a quick improper fix. >>>>>>>>>>> >>>>>>>>>>> The only recourse now for removing the cb is to take off the >> white >>>>>>>>>>> whatever it is, throw it away. lift out the cb. Fix what has to >> be >>>>>>>>>>> fixed. AND THEN REASSEMBLE THE ENTIRE CB SYSTEM AS GOD AND GB >>>>>>>>> DESIGNED >>>>>>>>>>> IT TO BE. >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> On 5/24/20 7:17 PM, Mary Lou Troy wrote: >>>>>>>>>>>> Hi Olivier, >>>>>>>>>>>> >>>>>>>>>>>> The laminate is not standard R22 construction. >>>>>>>>>>>> >>>>>>>>>>>> At one point we were going to do something to the board, I >> forget >>>>>>>>>>>> what, maybe replace the pennant or get rid of the pully in the >>>>>>>>> raising >>>>>>>>>>>> system and had ordered a new gasket from Stan. When we got it >>>>> apart >>>>>>>>>>>> and discovered the laminate, we abandoned the project. We asked >>>>> Stan >>>>>>>>>>>> about it and via email he basically shrugged his shoulders and >>>>> said >>>>>>>>>>>> something to the effect that "that wasn't our repair." It >> wasn't >>>>>>>>>>>> leaking, we found another way to do what we were going to do >> and >>>>>>>>>>>> forgot about it. In fact I didn't realize I still had the >>> exchange >>>>>>>>>>>> with Stan in an old email program until now. >>>>>>>>>>>> >>>>>>>>>>>> After a bit of back and forth on a photo, Stan's exact words on >>>>> the >>>>>>>>>>>> subject from 2003 were: >>>>>>>>>>>> >>>>>>>>>>>> "So what I am seeing is a fiberglass "washer" between the top >> lip >>>>> of >>>>>>>>>>>> the trunk and >>>>>>>>>>>> neoprene gasket. The question then is was there any leakage >>>>> between >>>>>>>>>>>> the fiberglass >>>>>>>>>>>> gasket and the cb trunk lip? If no then I would leave it in >>> place >>>>>>>>> and >>>>>>>>>>>> just use a >>>>>>>>>>>> jib saw to cut on opening in it to match the opening in the cb >>>>>>>>> trunk - >>>>>>>>>>>> it should >>>>>>>>>>>> cut easily since it is probably not very thick If on the other >>>>> hand >>>>>>>>>>>> there was >>>>>>>>>>>> leakage between this element and the cb trunk cap I would do >>>>>>>>> whatever >>>>>>>>>>>> is necessary >>>>>>>>>>>> to pull it off and throw it away and sand smooth the top of the >>>>>>>>> trunk >>>>>>>>>>>> lip to >>>>>>>>>>>> receive the neoprene gasket." >>>>>>>>>>>> >>>>>>>>>>>> As I noted above, it wasn't leaking so my recollection is we >>>>> decided >>>>>>>>>>>> not to mess with it. >>>>>>>>>>>> >>>>>>>>>>>> Sorry this isn't more help. >>>>>>>>>>>> >>>>>>>>>>>> Mary Lou >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> On 5/24/2020 6:12 PM, Olivier Hecht wrote: >>>>>>>>>>>>> My last message with two pics bounced back...hopefully this >> goes >>>>>>>>>>>>> through... >>>>>>>>>>>>> >>>>>>>>>>>>> Whoops...sorry. Forgot to attach it! Here they are. That >> white >>>>>>>>> piece is >>>>>>>>>>>>> glued to the boat...I’m sure of it. >>>>>>>>>>>>> >>>>>>>>>>>>> >>>>>>>>>>>>> On Sun, May 24, 2020 at 6:02 PM Richard Beytagh < >>>>>>>>> rbeytagh at gmail.com> >>>>>>>>>>>>> wrote: >>>>>>>>>>>>> >>>>>>>>>>>>>> The pic didn’t come through? >>>>>>>>>>>>>> >>>>>>>>>>>>>> On Sun, May 24, 2020 at 5:58 PM Olivier Hecht < >>>>> oehecht at gmail.com> >>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>> >>>>>>>>>>>>>>> Well the board fell onto the trailer axle since I guess I >>>>> pulled >>>>>>>>>>>>>>> the boat >>>>>>>>>>>>>>> too far forward. Took a chunk out of it so I decided to try >> to >>>>>>>>> pull >>>>>>>>>>>>>>> it. I >>>>>>>>>>>>>>> just got the cap off after removing ~60 10mm bolts with >> blind >>>>>>>>> nuts and >>>>>>>>>>>>>> now >>>>>>>>>>>>>>> I can’t access the pivot to remove the board. See pics...the >>>>>>>>> white >>>>>>>>>>>>>>> piece >>>>>>>>>>>>>> of >>>>>>>>>>>>>>> laminate? seems to be glasses into the hull. I’m afraid to >>>>>>>>> destroy >>>>>>>>>>>>>>> it by >>>>>>>>>>>>>>> prying. Can anyone confirm to me that this piece should be >>>>>>>>>>>>>>> removable? I >>>>>>>>>>>>>>> cants see any other way to lift the board out since the >> pivot >>>>> is >>>>>>>>>>>>>>> inaccessible. I’ll be at the boat for an hour more max, >> then I >>>>>>>>> have to >>>>>>>>>>>>>> head >>>>>>>>>>>>>>> home. Was really hoping to take the board with me! >>>>>>>>>>>>>>> >>>>>>>>>>>>>> -- >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> ~~~ _/) ~~~ >>>>>>>>>>>>>> >>>>>>>>>>>>>> Richard Beytagh >>>>>>>>>>>>>> Phone: 828 337 0180 >>>>>>>>>>>>>> >>>>>>>>>>>>> -------------- next part -------------- >>>>>>>>>>>>> A non-text attachment was scrubbed... >>>>>>>>>>>>> Name: IMG_3661.jpg >>>>>>>>>>>>> Type: image/jpg >>>>>>>>>>>>> Size: 2852710 bytes >>>>>>>>>>>>> Desc: not available >>>>>>>>>>>>> URL: >>>>>>>>>>>>> < >>>>>>>>>>> >>>>>>>>> >>>>> >>> >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20200524/1a8b1c27/attachment.jpg >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>> -------------- next part -------------- >>>>> A non-text attachment was scrubbed... >>>>> Name: IMG_3700.jpg >>>>> Type: image/jpeg >>>>> Size: 2017697 bytes >>>>> Desc: not available >>>>> URL: < >>>>> >>> >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20200601/3d760085/attachment.jpg >>>>>> >>>>> >>> >>> >> >>
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 