< prior
Back to Month
Go to Thread
2020-06-15; 17:11:32 EDT
Member Since
2019-06-04
Posts: 463
Hi Ric, the photo got stripped but your description led me to the right part. I measured and the opening where the pendant comes through to the cockpit on my boat is also 5/8". Thanks for the info.See the original archive post
On Mon, Jun 15, 2020 at 8:22 AM Richard Stott <ric at stottarchitecture.com> wrote: > Hopefully the attached photo will stay attached. Where the pendant comes > to of the hull at the cam cleat, I have a plastic thru-hull fitting. > > > > Attwood Plastic Mushroom Head Thru-Hull Fitting - 5/8” > Please confirm diameter before purchase > > > Ric > Dadventure > HBNY > > Richard Stott, AIA, LEED AP > www.stottarchitecture.com > Office 631-283-1777 > Cell 516-965-3164 > > > > > > > On Jun 14, 2020, at 4:10 PM, John Carlson via Rhodes22-list < > rhodes22-list at rhodes22.org> wrote: > > > > Well, this is a timely question — I just tightened that last of the 54 > bolts holding the centerboard cap in place last night (my boat isn’t in the > water). For the second time. I do have some pics. My diamond board was in > rough shape. I don’t think it liked Lake Waco. > > > > I am not sure what the best way to attach images is. I am going to try > attaching them to this message, but I’ve also shared them on Dropbox here > (zipped together): > > > > https://www.dropbox.com/s/7tum1gvszoc8eom/rhodes-centerboard.zip?dl=0 < > https://www.dropbox.com/s/7tum1gvszoc8eom/rhodes-centerboard.zip?dl=0> > > > > While I am sure this can be done underwater, I am not sure I would be > brave enough to try it with zero visibility. Taking the centerboard cap off > and lifting the diamond board out should be done out of the water. It isn’t > easy either, but you can see what you are doing. > > > > > > John Carlson > > Lillipelli 2004 (recycled 2012) > > > > > > > >> On Jun 13, 2020, at 9:25 PM, Graham Stewart <gstewart8 at cogeco.ca > <mailto:gstewart8 at cogeco.ca>> wrote: > >> > >> Jesse: > >> I have the older centerboard so others might well have better advice. > >> > >> What you suggest should work. I have never tried to do this type of > work while the boat was in the water. I have always had the boat on the > trailer and removed the centerboard cap - which is, admittedly, a pita. The > advantage of doing it with the cap removed is that you get to inspect the > centerboard for damage and check all of the blocks to make sure they are > still working properly. Mine were not. > >> > >> My line is 12' long. It passes through a series of blocks so that when > the board is down it uses quite a bit more line than you might think. In > your circumstance I would not use less than 12'. Don't overlook tying the > bitter end of the new line inside the boat so that you don't pull the whole > line through. > >> > >> Use the same thickness of line as is currently installed. > >> > >> Given that you must pass through a series of blocks the join between > the lines should be strong and flexible. > >> > >> > >> If anything goes wrong - such as the line separating, you will want to > have a backup plan to get the boat on its trailer while the board is down. > Driving the boat onto the trailer should result in the board being lifted > automatically by the keel roller but I would want to test this on your rig > before committing to removing the line. > >> > >> Graham Stewart > >> gstewart8 at cogeco.ca <mailto:gstewart8 at cogeco.ca> > >> > >> -----Original Message----- > >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org <mailto: > rhodes22-list-bounces at rhodes22.org>] On Behalf Of Jesse Shumaker > >> Sent: Saturday, June 13, 2020 9:21 PM > >> To: The Rhodes 22 Email List > >> Subject: [Rhodes22-list] Replacing diamondboard pendant > >> > >> Hi all, > >> > >> My R22 was built in 1991 and refurbished in 2013 before I bought it. It > >> appears that my boat has the diamondboard (rather than centerboard) with > >> the direct pull line. As you can see from the attached photos, the > pendant > >> is wearing through to the point that I'm worried about it going all the > way > >> through so I want to replace the line before that happens. In the > photos, > >> I didn't quite pull the diamondboard all the way back (a little over 1" > >> from being fully pulled up) so you can see the fraying just before it > goes > >> in the hole. > >> > >> Today I put some goggles on, took a deep breath and dove under the boat > a > >> few times to locate where the pendant ties on to the daggerboard. > >> Unfortunately, our lake water is so murky that I can't really see any > >> detail beyond that there is a diamondboard extending down from the > keel. I > >> can't even see the line, but I can feel where it ties on. > >> > >> From reading past posts regarding the diamondboard, it appears like 6 - > 8' > >> line should be sufficient. Does anyone recommend a specific type of > line? > >> > >> Here's my initial thoughts on steps to replace the pendant: > >> 1) Remove the handle from the old pendant > >> 2) Attach the handle to the new pendant > >> 3) Attach the new pendant to the old pendant > >> 4) Go below and pull the old pendant and keep pulling through until I > get > >> to where the old and new pendant are attached > >> 5) Separate the new and old pendant > >> 6) Untie the old pendant from the diamondboard or cut it off > >> 7) Tie the new pendant to the diamondboard using a bowline knot > >> > >> Some additional thoughts: > >> > >> There's not a lift available at our sailing club so attaching the new > >> pendant will be an underwater adventure. Considering the visibility > level > >> in the water is so low, I'll have to be doing a lot of this by feel > which > >> means it will take longer than I can hold my breath. I'm going to see > if I > >> can borrow some scuba gear from another sailor at the club. > >> > >> To attach the old and new pendants together, I'll use some very small > line > >> to tie them together, or perhaps some glue and/or tape. It doesn't look > >> like there is enough room to tie the old and new pendant together with a > >> knot and still have it fit through the hole. > >> > >> I'm going to err on the side of using a longer than needed pendant line > and > >> then cut it to length up top after it has been tied in from below. > >> > >> Does anyone have any pictures of where the pendant connects to the > >> diamondboard? > >> > >> Are there any suggestions from the group before I proceed? > >> > >> Thanks, > >> Jesse Shumaker > >> S/V Zephyr > >> -------------- next part -------------- > >> A non-text attachment was scrubbed... > >> Name: 20200613_180407.jpg > >> Type: image/jpeg > >> Size: 497647 bytes > >> Desc: not available > >> URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment.jpg > < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment.jpg > >> > >> -------------- next part -------------- > >> A non-text attachment was scrubbed... > >> Name: 20200613_180359.jpg > >> Type: image/jpeg > >> Size: 800238 bytes > >> Desc: not available > >> URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment-0001.jpg > < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment-0001.jpg > >> > >> > > > > > >> On Jun 14, 2020, at 12:01 PM, ROGER PIHLAJA <roger_pihlaja at msn.com> > wrote: > >> > >> Hi All, > >> > >> FYI, the use of a smaller line to establish a path for a larger line is > called “sending a messenger line”. The term comes from the old days of > sailing when a small cannon was used to fire the messenger line from one > ship to another or from the beach to a foundering ship, to be followed up > with the larger line. The technique is still used right up to this day to > rig up hose from a tanker to another ship for refueling at sea. Even > nuclear powered aircraft carriers need regular deliveries of jet fuel for > their aircraft. > >> > >> Roger Pihlaja > >> S/V Dynamic Equilibrium > >> > >> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986 < > https://go.microsoft.com/fwlink/?LinkId=550986>> for Windows 10 > >> > >> From: Jesse Shumaker<mailto:jesse.laten.shumaker at gmail.com> > >> Sent: Sunday, June 14, 2020 10:23 AM > >> To: The Rhodes 22 Email List<mailto:rhodes22-list at rhodes22.org> > >> Subject: Re: [Rhodes22-list] Replacing diamondboard pendant > >> > >> Ric, thanks for the note regarding the flange. I will address that as > >> well. It is good to know that it looks like I have some time before the > >> pendant parts in two. The guy at our sailing club with the SCUBA gear > is > >> out of town until late August or early September so this will be a > project > >> for late in the season. Until then, I'll avoid cleating where it is > >> wearing through. > >> > >> On Sun, Jun 14, 2020 at 6:58 AM Ric Stott <ric at stottarchitecture.com> > wrote: > >> > >>> If you carefully tape the new line to old with electrical tape, but > end to > >>> but end you should be able to pull a new line through, even if yo have > the > >>> old style CB with blocks. Be sure to use flexible line of the same > >>> diameter. > >>> One observation of you photo at the frayed line. You are missing a > plastic > >>> flange to the top of the pendant hole in the fiberglass. The flange is > >>> rounded and helps prevent the wear you are observing. Lastly. You have > >>> some time before the pendant wears thru. > >>> Ric > >>> Dadventure > >>> HBNY > >>> > >>> Sent from my iPhone > >>> > >>>> On Jun 14, 2020, at 7:32 AM, Jesse Shumaker < > >>> jesse.laten.shumaker at gmail.com> wrote: > >>>> > >>>> ?Hi Rick, thanks for your input. I like your idea to use the fishing > as > >>> a > >>>> threader and I plan to do that. > >>>> > >>>> I have been pulling up the board when in my slip because the boat gets > >>> some > >>>> side to side roll and the board can knock around a bit. Also, I pull > up > >>>> the board at least part way when I am pulling in my slip when wind is > >>>> coming off the lake at my stern. I go past my slip just a bit and > then > >>>> quickly turn to head up into the wind slightly before turning into my > >>>> slip. It gets pretty shallow past my slip (there's only one more boat > >>>> towards the beach after mine) so pulling up the board lessens the > draft > >>> to > >>>> give some room when executing that maneuver. > >>>> > >>>> I might hold off on replacing the pennant until it is hauled out as > >>>> suggested. Until then, when I need to pull up the board, I suppose > that > >>> I > >>>> could just pull it up part of the way so the frayed portion of the > line > >>> is > >>>> not resting in the cleat. > >>>> > >>>>> On Sat, Jun 13, 2020 at 9:56 PM Rick Lange <sloopblueheron at gmail.com > > > >>> wrote: > >>>>> > >>>>> Jesse, > >>>>> > >>>>> If your boat stays wet all season, why do you have to pull the board > up? > >>>>> If you need to knock off mussels, just pull it up and down a couple > >>> inches > >>>>> each week. Replace the pennant more easily when the boat is hauled > out. > >>>>> > >>>>> There isn't enough room to pull through the knot tying together the > old > >>> and > >>>>> new pennants. Use fishing line as a threader. > >>>>> > >>>>> Regards, > >>>>> > >>>>> Rick Lange > >>>>> > >>>>> > >>>>> On Sat, Jun 13, 2020 at 9:20 PM Jesse Shumaker < > >>>>> jesse.laten.shumaker at gmail.com> wrote: > >>>>> > >>>>>> Hi all, > >>>>>> > >>>>>> My R22 was built in 1991 and refurbished in 2013 before I bought it. > >>> It > >>>>>> appears that my boat has the diamondboard (rather than centerboard) > >>> with > >>>>>> the direct pull line. As you can see from the attached photos, the > >>>>> pendant > >>>>>> is wearing through to the point that I'm worried about it going all > the > >>>>> way > >>>>>> through so I want to replace the line before that happens. In the > >>>>> photos, > >>>>>> I didn't quite pull the diamondboard all the way back (a little > over 1" > >>>>>> from being fully pulled up) so you can see the fraying just before > it > >>>>> goes > >>>>>> in the hole. > >>>>>> > >>>>>> Today I put some goggles on, took a deep breath and dove under the > >>> boat a > >>>>>> few times to locate where the pendant ties on to the daggerboard. > >>>>>> Unfortunately, our lake water is so murky that I can't really see > any > >>>>>> detail beyond that there is a diamondboard extending down from the > >>>>> keel. I > >>>>>> can't even see the line, but I can feel where it ties on. > >>>>>> > >>>>>> From reading past posts regarding the diamondboard, it appears like > 6 - > >>>>> 8' > >>>>>> line should be sufficient. Does anyone recommend a specific type of > >>>>> line? > >>>>>> > >>>>>> Here's my initial thoughts on steps to replace the pendant: > >>>>>> 1) Remove the handle from the old pendant > >>>>>> 2) Attach the handle to the new pendant > >>>>>> 3) Attach the new pendant to the old pendant > >>>>>> 4) Go below and pull the old pendant and keep pulling through until > I > >>> get > >>>>>> to where the old and new pendant are attached > >>>>>> 5) Separate the new and old pendant > >>>>>> 6) Untie the old pendant from the diamondboard or cut it off > >>>>>> 7) Tie the new pendant to the diamondboard using a bowline knot > >>>>>> > >>>>>> Some additional thoughts: > >>>>>> > >>>>>> There's not a lift available at our sailing club so attaching the > new > >>>>>> pendant will be an underwater adventure. Considering the visibility > >>>>> level > >>>>>> in the water is so low, I'll have to be doing a lot of this by feel > >>> which > >>>>>> means it will take longer than I can hold my breath. I'm going to > see > >>>>> if I > >>>>>> can borrow some scuba gear from another sailor at the club. > >>>>>> > >>>>>> To attach the old and new pendants together, I'll use some very > small > >>>>> line > >>>>>> to tie them together, or perhaps some glue and/or tape. It doesn't > >>> look > >>>>>> like there is enough room to tie the old and new pendant together > with > >>> a > >>>>>> knot and still have it fit through the hole. > >>>>>> > >>>>>> I'm going to err on the side of using a longer than needed pendant > line > >>>>> and > >>>>>> then cut it to length up top after it has been tied in from below. > >>>>>> > >>>>>> Does anyone have any pictures of where the pendant connects to the > >>>>>> diamondboard? > >>>>>> > >>>>>> Are there any suggestions from the group before I proceed? > >>>>>> > >>>>>> Thanks, > >>>>>> Jesse Shumaker > >>>>>> S/V Zephyr > >>>>>> -------------- next part -------------- > >>>>>> A non-text attachment was scrubbed... > >>>>>> Name: 20200613_180407.jpg > >>>>>> Type: image/jpeg > >>>>>> Size: 497647 bytes > >>>>>> Desc: not available > >>>>>> URL: < > >>>>>> > >>>>> > >>> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment.jpg > >>>>>>> > >>>>>> -------------- next part -------------- > >>>>>> A non-text attachment was scrubbed... > >>>>>> Name: 20200613_180359.jpg > >>>>>> Type: image/jpeg > >>>>>> Size: 800238 bytes > >>>>>> Desc: not available > >>>>>> URL: < > >>>>>> > >>>>> > >>> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200613/40791568/attachment-0001.jpg > >>>>>>> > >>>>>> > >>>>> > >>> > >> > >> > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 