< prior
Back to Month
Go to Thread
2020-06-21; 10:10:15 EDT
Member Since
2018-11-06
Posts: 73
To follow up on my failed launch last month, I got my boat repaired at the marina and ended up paying $1080. Not too bad. Picture of the repair attached. I launched the boat yesterday and it all went smoothly. I opened the cover of the bilge fully to empty the remaining water and check for leaks, and it’s all good now. I was a bit worried that the centerboard trunk cap had been damaged, but it’s in perfect shape. The sailing season starts now! Alexis IMG_2645.jpg IMG_2594.jpgSee the original archive post
On Tue, May 12, 2020 at 11:01 AM Lowe, Rob <rlowe at vt.edu> wrote: > Alexis, > Cool, those tires look adequate. The reason I ask is I had never paid any > attention to my trailer tires, I just assumed they were adequate. One day > I'm in the midst of taking my boat to the lake and I'm in a parking lot. I > happened to look in my side mirror at the boat and noticed the trailer tire > was split right now the middle of the tread and what looked like an inner > tube was visible! Upon further inspection I discovered the tires were > standard automotive tires and not adequate for a trailer. I didn't have a > spare tire with me. I ended up leaving the boat where it was and came back > with a jack and stands. I took both tires off and took them to be replace > with trailer tires. So now I pay attention to trailer tires. - rob > > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Alexis Seigneurin <alexis.seigneurin at gmail.com> > Sent: Tuesday, May 12, 2020 10:40 AM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > Thanks, Rob. > > The previous owner had done a good job keeping the boat in good shape. > It’s all on my shoulders now... > > The tires I used are Carlisle Sport Trail ST 225/75D15 LRD. I believe this > is what was originally used on the trailer, and the load range (D) should > be adequate. > > And you’re right, I don’t have the mast crutch and raising system on the > boat. I use wood supports to hold the mast in place when trailering, and I > keep the other accessories inside the cabin. I feel like the mast is more > solidly held in place this way. > > Good to know about welding brackets on the trailer. I don’t think I am > going to have to do that this time but I will keep that in mind for the > future. > Alexis > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Lowe, Rob <rlowe at vt.edu> > Sent: Tuesday, May 12, 2020 8:51:08 AM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > Alexis, > Nice looking boat. Hope you get her repaired and splashed soon. > > I had similar problems with my bunks and ended up replacing all of them. > I also had to have a couple of the metal support pieces re welded. If you > need to go that route, make sure they are welded vertically. They welded > mine on perpendicular to the frame which made them too close together. > This was for the keel guide boards and I could not get the boat loaded as > the keel would not slide it. I ended up replacing the 2X guide boards with > 1X which gave me sufficient room. > > What type of tires did you put on the trailer? I hope trailer tires, > automobile tires do not have the weight capacity you will need. Good time > to take a look. > > I notice you do not have the mast crutch. How about the mast raising > system? A word from experience, when you raise the mast you'll want to get > the aft end of it much higher up in the air before you raise. Good luck! - > rob > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Alexis Seigneurin <alexis.seigneurin at gmail.com> > Sent: Monday, May 11, 2020 4:20 PM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > My trailer is a single-axle Triad trailer. All the galvanized steel is in > good shape. It’s just the wood that was probably too old, and the screws > came off. > > I am attaching a picture of the bracket that ended up sticking out. It’s > the little one, on the inside bunk, not the outside one. > > And yes, you can see I had a flat tire. I am not being very lucky this > year... I did replace both tires as they were from 2007, which - I also > learned the hard way - is past age. > > Regarding the rollers, I think my trailer only has one at the aft end. I > think it supports the centerboard but nothing else. > > Alexis > > [Image.jpeg] > > [Image.jpeg] > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Michael D. Weisner <mweisner at ebsmed.com> > Sent: Monday, May 11, 2020 12:26:47 PM > To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > I actually carry a roll of Flex Tape (as seen on TV holding a boat > together) > purchased from Home Depot: > > https://www.homedepot.com/p/FLEX-SEAL-FAMILY-OF-PRODUCTS-Flex-Tape-Black-4-i > n-x-5-ft-Strong-Rubberized-Waterproof-Tape-TFSBLKR0405/302634866 > <https://www.homedepot.com/p/FLEX-SEAL-FAMILY-OF-PRODUCTS-Flex-Tape-Black-4-in-x-5-ft-Strong-Rubberized-Waterproof-Tape-TFSBLKR0405/302634866> > > The commercial also shows the tape's waterproof property by patching a hole > in an aquarium FROM THE INSIDE, not really useful for a hole in a boat, I > would think. > > I found an investigative report that seems to validate the commercial claim > at: > > https://www.insideedition.com/investigative/25621-are-the-commercials-hyped- > up-investigation-tests-whether-flex-tape-can-hold-a-boat-together > <https://www.insideedition.com/investigative/25621-are-the-commercials-hyped-up-investigation-tests-whether-flex-tape-can-hold-a-boat-together> > > Hopefully, I will never need to use it. According to my "friend", Mr. > Murphy, in the unlikely event that I will need the tape, the adhesive will > probably be dried out! > > Mike > s/v Wind Lass ('91) > Nissequogue River, NY > I'd rather be sailing :~) > > > -----Original Message----- > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of > Lowe, > Rob > Sent: Monday, May 11, 2020 12:07 PM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > Not that I'm planning on holing my boat, but I wonder if any boaters carry > tape that could be applied to a hole like this underwater? - rob > > > https://www.homedepot.com/p/Intertape-Polymer-Group-3-in-x-5-yds-VersaTape-U > nderwater-Tape-99688/206300616 > <https://www.homedepot.com/p/Intertape-Polymer-Group-3-in-x-5-yds-VersaTape-Underwater-Tape-99688/206300616> > > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Alexis > Seigneurin <alexis.seigneurin at gmail.com> > Sent: Sunday, May 10, 2020 12:37 PM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > I am quite impressed most of you are recommending for me to do the repair > myself! I have watched countless hours of Boatworks Today and Sail Life > videos, so I kind of know the steps for this repair, but I wasn't feeling > like it was a good first project for a fiberglass repair. It's structural > and under the water line, so definitely needs to be done right. I will > think > about it and we'll see what I decide! > > Thanks all, > Alexis > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of Hank > <hnw555 at gmail.com> > Sent: Sunday, May 10, 2020 12:29:08 PM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Launch... and the story of an epic failure > > I also didn't have the benefit of all of the youtube videos now available > to > show folks how to do things when I did my first fiberglass repair. Much > easier to be a DIYer these days. > > On Sun, May 10, 2020 at 10:00 AM Mark Whipple <mark at whipplefamily.com> > wrote: > > > I agree that fiberglass work is not difficult, but I would also > > suggest that repairing a hole below the waterline may not be the best > > first-time project. It would be great, though, if you could find > > someone to give you a hand like Hank was able to that would be idea. > > FWIW I would recommend Allan H. Vaites Fiberglass Repair Manual < > > https://smile.amazon.com/dp/0071569146?tag=amz-mkt-chr-us-20&ascsubtag > > =1ba00-01000-org00-mac00-other-smile-us000-pcomp-feature-scomp-wm-5&re > > f=aa_scomp > > > > > . > > > > Mark Whipple > > > > > > > > On Sun, May 10, 2020 at 9:14 AM Hank <hnw555 at gmail.com> wrote: > > > > > This is definitely true. I had some fiberglass issues on another > > > boat > > that > > > I used to own and was gonna have the yard do it.Instead one of the > > > other guys in the marina showed me that it wasn't that hard to do > > > and I did it myself. Very satisfying and glad I was a able to learn > > > these skills. If you are at all handy you can probly do this yourself > as well. > > > > > > On Sun, May 10, 2020, 05:39 JeffSmith <jeffsmithphoto at gmail.com> > wrote: > > > > > > > Fiberglass work is fairly easy, if you have the time and access to > > > > the boat. > > > > Check out some YouTube videos and figure out whether you have the > > skills > > > > and > > > > patience. You probably do. > > > > > > > > > > > > > > > > ----- > > > > Jeff Smith > > > > 2009 R22 #101 RADIANT > > > > Atlantic Highlands Municpal Harbor Atlantic Highlands, NJ > > > > > > > > -- > > > > Sent from: http://rhodes-22.1065344.n5.nabble.com/ > > > > > > > > > > > > > -- > > 2000 R22 *Tiny Dancer* > > 1986 Nimble 30 (For Sale) > > 1982 Com-Pac 15 (For Sale) > > Boston, MA > > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Image.jpeg > Type: image/jpeg > Size: 406421 bytes > Desc: Image.jpeg > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200511/4536cf86/attachment.jpeg > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Image.jpeg > Type: image/jpeg > Size: 1287842 bytes > Desc: Image.jpeg > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200511/4536cf86/attachment-0001.jpeg > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 