< prior
Back to Month
Go to Thread
2020-08-18; 12:10:50 EDT
Member Since
2019-09-28
Posts: 84
Interesting, thanks Graham.See the original archive post
On Tue, Aug 18, 2020 at 11:41 AM Graham Stewart <gstewart8 at cogeco.ca> wrote: > Regarding the use of silicone for ports. > > Beckson, one of the largest manufacturer specifies that silicone SHOULD be > used : > > Their installation instructions are found here: > https://www.beckson.com/installport.html > > "Choice of Sealant: > > There are many brands of caulk, adhesive and sealant available in your > marine chandlery or hardware store, but be wary, not all are like. Many are > for specific applications and may contain solvents that are destructive to > thermoplastics. Chemical solvents should not be used for clean up. > > Beckson recommends 100% silicone sealant only. > > Beckson recommends 100% silicone sealant only. Availability of silicone > varies regionally. Please contact your sealant manufacturer for the most up > to date information with regard to materials and compatibility. Silicone > has been around for nearly 50 years without sign of failure. Most other > caulks and sealants fail after 10 years. When a port is installed properly, > silicone works best for years of enjoyment. > > Sanding previously caulked areas: > > Previously caulked or sealed areas must be sanded in order to remove the > old caulk. If not removed, a strong bond will not occur. Surfaces may > appear to be free of caulk to the eye, but residue may still be present on > the gel coat. Sand lightly with 220 grit paper to prepare for the silicone > sealant." > > Check with the port manufacturer before deciding. Butyl is probably a safe > choice but while it is an excellent sealant it is very weak as an adhesive. > On a slightly curves surface that adhesive quality might be important. > > Graham Stewart > gstewart8 at cogeco.ca > > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf > Of Mitch Mitchell > Sent: Tuesday, August 18, 2020 10:48 AM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Bilge > > Thanks Mark, hopefully the previous owner didn't use silicone. I'm hoping > the port frame will come off easily. > > On Tue, Aug 18, 2020 at 10:39 AM Mark Whipple <mark at whipplefamily.com> > wrote: > > > Hi Mitch, > > > > I'm not an expert on sealants but I think butyl tape would work for > > resealing the ports. What I am sure of is you should NEVER use a > > silicone-based sealant on a boat. Silicone makes a chemical bond with any > > surface it touches. Once you have silicone on a surface, nothing else > will > > bond to it - not even more silicone. When you think you've removed > silicone > > from a surface there is still residue you can't see. You have to apply a > > chemical called a "digester" to chemically break down and remove the > > silicone residue. I was recently repairing a skylight on my Nimble 30 and > > had to do the job all over because the sealant I used failed to bond. I > > didn't realize silicone had been used previously. > > > > Mark > > -- > > Boston, MA > > > > 2000 R22 *Luna Mia* > > 1987 Nimble 30 *For Sale* > > 1982 Com-Pac 16 *For Sale* > > > > On Tue, Aug 18, 2020 at 10:28 AM Mitch Mitchell <mitchpadl at gmail.com> > > wrote: > > > > > I have also discovered water in the bilge whenever the boat is in the > > rain > > > and not covered. I have traced it to a window, the vhf connector and > > water > > > also shows up in the lazarette. I know that there have been a number of > > > threads on this before but wondering if there is a consensus on the > best > > > way to seal the small windows? I'm thinking butyl tape but not sure. > I've > > > also had the bilge seem dry but if I lift the bow up water magically > > > appears and if I dry it and then lower the bow (on trailer) then once > > again > > > more water appears as it must be seeping in from other areas. Any input > > > would be great. Thanks, Mitch > > > > > > On Mon, Aug 17, 2020 at 11:36 AM Michael Corley < > michael.4591 at gmail.com> > > > wrote: > > > > > > > I agree with Graham. "I think I have determined that water leaks in > my > > > > boat are a function of how my boat happens to be feeling at any > > > particular > > > > time." > > > > The little bit of water I get in my bilge comes mainly after > > rainstorms. > > > > No evidence of leaks . . . of course it could be the 21 year old > > ports > > > > and hatches need resetting/replacement. > > > > > > > > Mike > > > > S/V Ranger > > > > 99 Rhodes > > > > > > > > On Sun, Aug 16, 2020 at 10:40 PM Nancy <njcassie at optonline.net> > wrote: > > > > > > > > > Had a good rain today and will investigate in the morning. Feel > like > > a > > > > > detective > > > > > > > > > > Sent from my iPhone > > > > > > > > > > > On Aug 16, 2020, at 10:18 PM, Tex Hill <Tejas.Hill at outlook.com> > > > wrote: > > > > > > > > > > > > ?You are probably right, I have had similar experience.(: > > > > > > Tex > > > > > > > > > > > > Sent from my iPad > > > > > > > > > > > >> On Aug 16, 2020, at 9:05 PM, Graham Stewart < > gstewart8 at cogeco.ca> > > > > > wrote: > > > > > >> > > > > > >> ?Two seasons ago I had a variety of leaks in two windows, the > > > > > companion way, the vent and the lazarette. Any rain at all and the > > > water > > > > > would flow in. On the otherhand if I ried to locate the leak using > a > > > hose > > > > > and pouring copious amounts of water everywhere that seemed > suspect, > > no > > > > > water entered the boat. Last year, because of the highwater in lake > > > > Ontario > > > > > I was not able to launch and the boat remaind under cover. I > > committed > > > > > myself to track down and repair the leaks this year. I strung paper > > > towel > > > > > everywhere I thought was suspect and waited for a good rain to > > identify > > > > the > > > > > leaks based on the telltale signs left on the paper towel. We have > > had > > > a > > > > > number of torrential downpours this year and so far not a drop of > > water > > > > in > > > > > the boat. > > > > > >> > > > > > >> I think I have determined that water leaks in my boat are a > > function > > > > of > > > > > how my boat happens to be feeling at any particular time. > > > > > >> > > > > > >> Graham Stewart > > > > > >> Agile, Rodes 22, 1976 > > > > > >> Kingston Ontario > > > > > >> > > > > > >> > > > > > >> -----Original Message----- > > > > > >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] > > On > > > > > Behalf Of Tex Hill > > > > > >> Sent: Sunday, August 16, 2020 3:53 PM > > > > > >> To: The Rhodes 22 Email List > > > > > >> Subject: Re: [Rhodes22-list] Bilge > > > > > >> > > > > > >> My daughter had a subtle leak that was hard to see how water > got > > > > into > > > > > the bilge. They finally traced it to one of the ports, removed the > > > port, > > > > > caulked It . Problem solved. > > > > > >> Tex Hill > > > > > >> > > > > > >> Sent from my iPad > > > > > >> > > > > > >>>> On Aug 15, 2020, at 8:39 PM, Nancy <njcassie at optonline.net> > > > wrote: > > > > > >>> > > > > > >>> ?Thanks > > > > > >>> > > > > > >>> Sent from my iPhone > > > > > >>> > > > > > >>>>> On Aug 15, 2020, at 9:04 PM, Peter Nyberg < > > > peter at sunnybeeches.com> > > > > > wrote: > > > > > >>>> > > > > > >>>> ?It’s likely that something got soaked and water is continuing > > to > > > > > seep out slowly into the bilge. I’d keep an eye on it, but I doubt > > > it’s > > > > > anything to worry about. > > > > > >>>> > > > > > >>>> —Peter > > > > > >>>> > > > > > >>>>>> On Aug 15, 2020, at 7:58 PM, Nancy <njcassie at optonline.net> > > > > wrote: > > > > > >>>>> > > > > > >>>>> We had a lot of water in the bilge after the tropical storm. > > > Pumped > > > > > it all out. We seem to have 1/2” clear water in the bilge now. Eve. > > If > > > we > > > > > pump to dryness, it comes back clear, small amount. Thoughts? > > > > > >>>>> Thanks in advance. > > > > > >>>>> Nancy C > > > > > >>>>> Sent from my iPhone > > > > > >>>> > > > > > >>> > > > > > >> > > > > > > > > > > > > > > > > > > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 