< prior
Back to Month
Go to Thread
2020-09-11; 17:52:27 EDT
Member Since
2019-06-04
Posts: 463
Mark, thanks for the tip and link regarding the cutting oil. Jesse Shumaker S/V ZephyrSee the original archive post
On Fri, Sep 11, 2020 at 8:06 AM Mark Whipple <mark at whipplefamily.com> wrote: > A drill press allows you to keep a consistent angle and speed while > carefully controlling the downward pressure. There's also less of a > tendency for the drill bit to "walk," but I'd still use a punch to create a > set point for the drill bit. I'd also suggest using cutting oil (fluid) > when drilling any metal other than maybe aluminum or lead. > > https://www.amazon.com/s?k=cutting+oil > > > > On Fri, Sep 11, 2020 at 8:42 AM Jesse Shumaker < > jesse.laten.shumaker at gmail.com> wrote: > > > Thanks for the tips. I may give the step bit a try. > > > > On Thu, Sep 10, 2020 at 9:44 PM Graham Stewart <gstewart8 at cogeco.ca> > > wrote: > > > > > I like to use a step bit to gradually drill a larger hole in metal > > without > > > having to change bits. > > > > > > Graham Stewart > > > Agile, Rodes 22, 1976 > > > Kingston Ontario > > > > > > > > > -----Original Message----- > > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > > Behalf > > > Of Peter Nyberg > > > Sent: Thursday, September 10, 2020 8:59 PM > > > To: The Rhodes 22 Email List > > > Subject: Re: [Rhodes22-list] Pop Top Connection > > > > > > Starting with smaller holes and gradually expanding to larger holes is > > the > > > approach I usually take. I don’t know that it actually matters. > > > > > > Using a drill press may help to positions holes more accurately, other > > > than that, I haven’t noticed that it matters much over using a hand > > drill. > > > > > > —Peter > > > > > > > On Sep 10, 2020, at 6:48 PM, Jesse Shumaker < > > > jesse.laten.shumaker at gmail.com> wrote: > > > > > > > > I can confirm what Peter mentioned since I recently ordered mast > > > organizer > > > > model DH288 > > > > < > > > > > > https://www.dwyermast.com/items.asp?cat1ID=40&cat1Name=Hardware&familyID=19&familyName=Halyard+Organizer+Plates > > > > > > > > in > > > > preparation for fall projects. I attached a photo of the one that I > > > > received in the mail. Sorry for the poor lighting in the photo. It > > > occurs > > > > to me that I'll need to drill holes to fit the existing pattern on > the > > > > tabernacle. It appears I may want to use a drill press and > > > progressively > > > > larger bits for that given the strength of the material described in > > > > Roger's earlier post in this thread. > > > > > > > > Jesse Shumaker > > > > S/V Zephyr > > > > > > > > > > > > > > > > On Thu, Sep 10, 2020 at 10:56 AM Peter Nyberg < > peter at sunnybeeches.com> > > > > wrote: > > > > > > > >> I avoided having to cut off the tab by mounting the organizer > > backwards, > > > >> with the tab on the forward side. I don’t use the tab, but it’s not > > in > > > the > > > >> way there. > > > >> > > > >> The halyard organizer, for those who might be interested, came from > > > Dwyer ( > > > >> www.dwyermast.com). I just took a look at their current selection > of > > > >> organizers, and none appear to have a tab with a hole for mounting a > > > block > > > >> at the centerline; only port and starboard. > > > >> > > > >> Peter Nyberg > > > >> Coventry, CT > > > >> s/v Silverheels (1988/2016) > > > >> > > > >>> On Sep 10, 2020, at 10:40 AM, ROGER PIHLAJA <roger_pihlaja at msn.com > > > > > >> wrote: > > > >>> > > > >>> Graham, > > > >>> > > > >>> I actually have a modified version of Peter Nyberg’s mast step > > > >> organizer. I simply cut off the tab on the aft side so it wouldn’t > > > >> interfere with the pop top slider. Unfortunately, the 300 series > > > stainless > > > >> alloys have a strong tendency to work harden when they are cold > > > worked. It > > > >> takes a good metal cutting band saw with plenty of coolant to cut > thru > > > the > > > >> work hardened bent tab. Then, a bench grinder and fine emory cloth > > will > > > >> clean up the cut and round off the sharp edges. Having the anchor > > > points > > > >> on the port, starboard, and front sides of the mast is very handy. > > > >>> > > > >>> Roger Pihlaja > > > >>> S/V Dynamic Equilibrium > > > >>> > > > >>> Sent from my iPhone > > > >>> > > > >>>> On Sep 10, 2020, at 10:21 AM, Graham Stewart <gstewart8 at cogeco.ca > > > > > >> wrote: > > > >>>> > > > >>>> ?Roger: Thanks for the thorough response. It all makes sense. I > > wonder > > > >> why I didn't have that ring installed on my boat. A second option I > am > > > >> considering is to install a mast step organizer such as the one that > > > Peter > > > >> Nyberg installed on his boat. I don't have a Cunningham on my boat. > I > > > would > > > >> be interested in seeing what others have installed if anyone has > > > pictures. > > > >>>> > > > >>>> Graham Stewart > > > >>>> Agile, Rodes 22, 1976 > > > >>>> Kingston Ontario > > > >>>> > > > >>>> > > > >>>> -----Original Message----- > > > >>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] > On > > > >> Behalf Of ROGER PIHLAJA > > > >>>> Sent: Thursday, September 10, 2020 8:15 AM > > > >>>> To: The Rhodes 22 Email List > > > >>>> Subject: Re: [Rhodes22-list] Pop Top Connection > > > >>>> > > > >>>> Graham, > > > >>>> > > > >>>> Although, at first glance, the present pop top slider design may > > look > > > >> sort of crude, it’s actually pretty elegant. Remember, there are 2 > > > pieces > > > >> of tackle that have their lower anchor points on the pop top slider, > > the > > > >> boom vang and the Cunningham. The snap shackle for the Cunningham > > > actually > > > >> attaches to the eye strap and the snap shackle for the boom vang > > > actually > > > >> attaches to the ring. This way, the force from the Cunningham, > which > > is > > > >> vertical directly up the mast, is kept as close as possible to the > > mast. > > > >> The force from the Cunningham on the two machine screws attaching > the > > > eye > > > >> strap to the pop top slider is almost entirely shear, which is the > > most > > > >> mechanically efficient way to load a threaded connection. In > > addition, > > > by > > > >> attaching the Cunningham to the eye strap vs. the ring, the clam > cleat > > > on > > > >> the block automatically faces aft, thus facilitating ease of use > from > > > the > > > >> cockpit. Similarly, attaching the snap shackle for the boom vang > onto > > > the > > > >> ring vs. the eye strap, automatically positions the clam cleat > > downward > > > and > > > >> moves it aft slightly, both of which help prevent the two pieces of > > > tackle > > > >> from getting fouled up on each other and makes the boom vang easier > to > > > use > > > >> from the cockpit. > > > >>>> > > > >>>> If the ring were simply welded onto the pop top slider, I think it > > > >> might interfere with the pop top raising and lowering process. i.e. > > > When > > > >> the pop top is raised, the 1st step is to raise the aft end of the > pop > > > top > > > >> up on its support arms until the spring loaded detents lock into > > > position. > > > >> In this position, the front corner of the pop top might interfere > > with a > > > >> fixed welded ring on the pop top slider. The present design, with > its > > > eye > > > >> strap and ring, automatically folds down out of the way. Even with > > the > > > >> present pop top slider design, it’s not the eye strap and ring > that’s > > in > > > >> the way if you attempt to raise the pop top with the boom vang and > > > >> Cunningham in place, it’s the two pieces of tackle and all the > > > associated > > > >> line. Similarly, it’s not the eye strap and ring that tend to chip > up > > > the > > > >> front corner of the pop top, it’s the lower blocks and snap shackles > > on > > > the > > > >> Cunningham and boom vang that do the damage when they start flopping > > > >> around. A welded fixed ring wouldn’t change that. > > > >>>> > > > >>>> Finally, if the ring is welded onto the pop top slider; then, that > > > will > > > >> be a critical weld. There will be a lot of force on it. I hope you > > > are, > > > >> or have access to, a certified welder. > > > >>>> > > > >>>> Even after all these years, it’s fun to critically exam Stan’s > ideas > > > >> and designs that were so multifunctional. He was way ahead of us > all > > in > > > >> anticipating and solving problems. My boat is in its 44th season > and > > > it’s > > > >> been sailed hard. The pop top slider hasn’t given a bit of trouble. > > > >>>> > > > >>>> Roger Pihlaja > > > >>>> S/V Dynamic Equilibrium > > > >>>> > > > >>>> > > > >>>> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> > for > > > >> Windows 10 > > > >>>> > > > >>>> From: Graham Stewart<mailto:gstewart8 at cogeco.ca> > > > >>>> Sent: Wednesday, September 9, 2020 10:32 PM > > > >>>> To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> > > > >>>> Subject: Re: [Rhodes22-list] Pop Top Connection > > > >>>> > > > >>>> Roger: > > > >>>> I am thinking that it might be worth getting the ring welded to > the > > > >> plate at about a 30 degree an angle rather than having it flop > around > > in > > > >> the strap eye. Do you see a reason why that might not work? > > > >>>> > > > >>>> Graham Stewart > > > >>>> gstewart8 at cogeco.ca > > > >>>> > > > >>>> > > > >>>> -----Original Message----- > > > >>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] > On > > > >> Behalf Of ROGER PIHLAJA > > > >>>> Sent: Wednesday, September 9, 2020 5:24 PM > > > >>>> To: The Rhodes 22 Email List > > > >>>> Subject: Re: [Rhodes22-list] Pop Top Connection > > > >>>> > > > >>>> Graham, > > > >>>> > > > >>>> The slider is held in its various positions by a hair pin clip > that > > > >> inserts thru holes drilled thru the mast track. I always keep the > > hair > > > pin > > > >> clip in place to hold the slider down no matter whether I have > tension > > > on > > > >> the boom vang &/or Cunningham or not. S/V Dynamic Equilibrium came > > > rigged > > > >> with the boom vang and Cunningham downhaul when I purchased her. I > > > don’t > > > >> know if a previous owner drilled and tapped the pop top slider for > the > > > eye > > > >> strap. Or, maybe back in 1976, Stan might have offered a > “performance > > > >> mainsail package” that included a boom vang and Cunningham. There > is > > > also > > > >> an eye strap drilled and tapped into the underside of the boom for > the > > > top > > > >> anchor point on the boom vang. It all looks pretty professional if > > they > > > >> are homemade and they both serve their mainsail shaping functions > > > >> perfectly. Both the boom vang and Cunningham must be removed to > raise > > > the > > > >> pop top. With snap shackles, installing and removing them is not a > > big > > > >> deal. A word of caution, all this hardware on the leading edge of > the > > > pop > > > >> top can chip the fiberglass if they get to banging around. I solved > > > this > > > >> problem by epoxying 10 gage SS sheet metal to the sides and the top > of > > > the > > > >> pop top near the pointy end where it attaches to the pop top slider. > > > >>>> > > > >>>> Roger Pihlaja > > > >>>> S/V Dynamic Equilibrium > > > >>>> > > > >>>> Sent from my iPhone > > > >>>> > > > >>>>> On Sep 9, 2020, at 4:13 PM, Graham Stewart <gstewart8 at cogeco.ca> > > > >> wrote: > > > >>>>> > > > >>>>> ?Roger: > > > >>>>> My 76 has the same bracket except that it does not have the ring > or > > > eye > > > >>>>> strap. I wonder if that was added by a previous owner. Do you > have > > a > > > >> track > > > >>>>> stop to keep the pop top down when the boom vang or Cunningham is > > in > > > >> use? If > > > >>>>> it works well I might copy that. > > > >>>>> > > > >>>>> Graham Stewart > > > >>>>> Agile, Rodes 22, 1976 > > > >>>>> Kingston Ontario > > > >>>>> > > > >>>>> > > > >>>>> -----Original Message----- > > > >>>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] > On > > > >> Behalf Of > > > >>>>> ROGER PIHLAJA > > > >>>>> Sent: Wednesday, September 9, 2020 1:32 PM > > > >>>>> To: John Carlson; The Rhodes 22 Email List > > > >>>>> Subject: Re: [Rhodes22-list] Pop Top Connection > > > >>>>> > > > >>>>> Hi All, > > > >>>>> > > > >>>>> I've attached a picture of the pop top slider connection on my > > older > > > >> (1976) > > > >>>>> standard (i.e. non IMF) mainsail Rhodes 22. As you can see, > it's a > > > >> simple > > > >>>>> weldment. The bent sheet metal slides up and down in the mast > > slot. > > > >> The > > > >>>>> bolt attaches to a pair of brackets on the leading edge of the > pop > > > >> top. The > > > >>>>> ring is the lower anchor point for the boom vang and Cunningham > > > >> downhaul > > > >>>>> tackle. > > > >>>>> > > > >>>>> [cid:image003.jpg at 01D686AD.A5678F20] > > > >>>>> > > > >>>>> Roger Pihlaja > > > >>>>> S/V Dynamic Equilibrium > > > >>>>> > > > >>>>> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> > for > > > >> Windows > > > >>>>> 10 > > > >>>>> > > > >>>>> From: John Carlson via Rhodes22-list<mailto: > > > rhodes22-list at rhodes22.org > > > >>> > > > >>>>> Sent: Wednesday, September 9, 2020 10:36 AM > > > >>>>> To: The Rhodes 22 Email List<mailto:rhodes22-list at rhodes22.org> > > > >>>>> Subject: Re: [Rhodes22-list] Pop top connection > > > >>>>> > > > >>>>> The front of mine is quite rough as well. I have a picture, but > it > > > >> looks a > > > >>>>> lot like yours (and I use a Mac). > > > >>>>> > > > >>>>> > > > >>>>> -- > > > >>>>> John. > > > >>>>> 2004/12 Rhodes 22 > > > >>>>> Waco, TX > > > >>>>> > > > >>>>> > > > >>>>> > > > >>>>>>>>> On Sep 9, 2020, at 9:26 AM, Mark Whipple < > > mark at whipplefamily.com > > > > > > > >> wrote: > > > >>>>>> New question: I'm looking at the piece that connects my pop-top > to > > > the > > > >>>>>> mast, and it looks unfinished on the forward end, like it may > have > > > >> been > > > >>>>>> broken at some point. I realize there are many small differences > > > >> between > > > >>>>>> our boats but do yours look like this? (Sorry for the blue tape > in > > > >> the way > > > >>>>>> - I removed it but then forgot to take another picture.) > > > >>>>>> Mark > > > >>>>>> -- > > > >>>>>> Boston, MA > > > >>>>>> 2000 R22 *Luna Mia* > > > >>>>>> 1987 Nimble 30 *For Sale* > > > >>>>>> 1982 Com-Pac 16 *For Sale* > > > >>>>>> -------------- next part -------------- > > > >>>>>> A non-text attachment was scrubbed... > > > >>>>>> Name: luna mia popup connection.jpg > > > >>>>>> Type: image/jpeg > > > >>>>>> Size: 24318 bytes > > > >>>>>> Desc: not available > > > >>>>>> URL: > > > >>>>> < > > > >> > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200909/b8bc1259/a > > > >>>>> ttachment.jpg> > > > >>>>> > > > >>>>> -------------- next part -------------- > > > >>>>> A non-text attachment was scrubbed... > > > >>>>> Name: 5D89362A40A344E489D4186D51FBAF96.jpg > > > >>>>> Type: image/jpeg > > > >>>>> Size: 153447 bytes > > > >>>>> Desc: 5D89362A40A344E489D4186D51FBAF96.jpg > > > >>>>> URL: > > > >>>>> < > > > >> > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200909/b8512c08/a > > > >>>>> ttachment.jpg> > > > >>>> > > > >>>> > > > >> > > > >> > > > > -------------- next part -------------- > > > > A non-text attachment was scrubbed... > > > > Name: DH288.JPG > > > > Type: image/jpeg > > > > Size: 73235 bytes > > > > Desc: not available > > > > URL: < > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20200910/70648fa1/attachment.jpe > > > > > > > > > > > > > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 