< prior
Back to Month
Go to Thread
2020-09-15; 15:20:57 EDT
Member Since
2020-03-29
Posts: 139
I am glad to read this exchange as I am hoping to get to Stan’s next month and bring home a winter project. I haven’t done any highway towing for a long time. The last thing I need is swaying at those speeds. Thanks all. Scott A. Sent from my iPhoneSee the original archive post
> On Sep 15, 2020, at 9:48 AM, ROGER PIHLAJA <roger_pihlaja at msn.com> wrote: > > ?Graham, > > I just measured my tongue weight at 343 lbs using a digital bathroom scale under the tongue jack. > > Remember, if you build some sort of bracket for your outboard on the tongue and stow it up there, you will get a much greater increase on tongue weight vs. just removing the motor from the transom. Just this one change would get you pretty close to where you should be. > > Roger Pihlaja > S/V Dynamic Equilibrium > > Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 > > From: Graham Stewart<mailto:gstewart8 at cogeco.ca> > Sent: Tuesday, September 15, 2020 9:41 AM > To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Almost perfect as can be - trailer > > Roger: > I am going to remove the motor and check the tongue weight again to see what > the difference is. I am thinking that the standard old Rhodes 22, motor and > trailer would weigh about 3200 lbs so the tongue weight should be at least > 320 lbs - which seems like a lot to me. > > If anyone knows their tongue weight it might be helpful to me and others if > they post it to da list. > > Graham Stewart > gstewart8 at cogeco.ca > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of > ROGER PIHLAJA > Sent: Tuesday, September 15, 2020 8:54 AM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Almost perfect as can be - trailer > > Graham, > > Given everything you've tried that didn't work, I am left with suggesting > your bunks need to be moved forward. It doesn't need to be much, probably > only a couple of inches. By any chance, could you move the bunk supports > from the aft side of the trailer crossmembers to the front side? If the > bunk supports are already on the front side of the crossmembers; then, you > will have to fabricate spacers and use longer grade 8 bolts to move the > bunks forward. The general rule of thumb is that you should have => 10% of > the trailer weight on the tongue for high speed stability. Your trailer is > way short of that. My wife won't let me have the excitement of having the > boat & trailer start to wag the tow vehicle on the expressway! > > Some other solutions would be to remove weight from the stern, like removing > the outboard and stowing it on the tongue. You could always tow with a full > water tank &/or move everything from the lazarette compartment to the > V-berth. But, all these solutions add time and royal PITA factor to rigging > and unrigging. > > Roger Pihlaja > S/V Dynamic Equilibrium > > Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows > 10 > > From: Graham Stewart<mailto:gstewart8 at cogeco.ca> > Sent: Monday, September 14, 2020 10:29 PM > To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Almost perfect as can be - trailer > > Now that I compare the picture of my boat with that of Optopian it seems > that it is just as far forward so maybe it isn't as bad as I thought. > > Graham Stewart > Agile, Rodes 22, 1976 > Kingston Ontario > > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of > Graham Stewart > Sent: Monday, September 14, 2020 9:45 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Almost perfect as can be - trailer > > I am one of those who has never been able to get my boat sufficiently > forward on the trailer. When I winch in the boat at the launch ramp the bow > eye goes under the bow brace even when it is fully retracted. As a result I > can't pull the boat in all the way. > > After leaving the ramp on to level ground of the boat the bow moves up > putting enormous pressure on the front of the boat. If I relieve the strain > on the winch the bow of the boat moves up and back. I took a picture of the > winch and brace after retrieving the boat today and attach it here. I also > weighed the tongue with the motor still on the transom. I think it should be > heavier that 140 lbs. > > Any suggestions would be welcome. > > Graham Stewart > Agile, Rodes 22, 1976 > Kingston Ontario > > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of > Lowe, Rob > Sent: Monday, September 14, 2020 11:43 AM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Almost perfect as can be - trailer > > Tom, > First off, sorry about your mishaps. I've done the same thing sort of. > Set the keel down on the guide bunks and broke one. > > Your need to get the support welded. Make sure they weld it at the same > angle as it was. I think they angle out a bit and the guy who welded mine > made it vertical, which meant the keel no long would fit between the boards. > I ended up replacing the 2 inch boards with 1 inch boards so the keel would > fit. > > Now to get the boat centered, I 'think' it was Stan that shared this wisdom. > Leave your centerboard down when retrieving. The centerboard will help > guide the boat into position on the trailer. Once centered and winched in , > PULL THE BOARD BACK UP. Does anyone else do it this way? It sure works for > me. > > Rob > > -----Original Message----- > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of Tom > Van Heule > Sent: Sunday, September 13, 2020 12:31 PM > To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > Subject: [Rhodes22-list] Almost perfect as can be - trailer > > Today I went to the up a launch lane to practice retrieval and launching our > boat Octopian. In the morning I had about negative 80lbs tounge weight, the > aft port window centered above the axle. Rudder and 8hp 4 stroke on the > back. Mast down on the crutch and attached to the bow pulpit. Single axle. > > Now see where the aft port is related to the axle. > We have about 120lbs of tounge weight now! Pulled remarkedly better. > > You may ask yourself.... Why almost perfect then? > We cracked one of the keel alignment bunks :( > > Let's share our tips for getting her just right in the bunks? I don't see a > lot of retrieval or launching threads on the archive. > > I found that winching her tight before de-floating, with the stem crotch > full retracted worked perfect. > Just make sure you give her time to settle in the bunk, it's not a tractor > pull... > > Hope everyone had a great weekend. > Tom > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: IMG_20200913_112144.jpg > Type: image/jpeg > Size: 3275134 bytes > Desc: not available > URL: > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20200913/b91b4f47/a > ttachment.jpg> > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: IMG_20200913_112058.jpg > Type: image/jpeg > Size: 4169607 bytes > Desc: not available > URL: > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20200913/b91b4f47/a > ttachment-0001.jpg> > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Position of boat on trailer.jpg > Type: image/jpeg > Size: 208192 bytes > Desc: not available > URL: > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20200914/44af9374/a > ttachment.jpg> > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Tongue weight with motor on transom.jpg > Type: image/jpeg > Size: 285648 bytes > Desc: not available > URL: > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20200914/44af9374/a > ttachment-0001.jpg> >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 