< prior
Back to Month
Go to Thread
2020-11-03; 21:21:06 EST
Member Since
2018-08-24
Posts: 42
Congratulations on the victory over 5200 Takes patience but it worksSee the original archive post
On Tue, Nov 3, 2020 at 6:36 PM, Tom Van Heule < tom.vanheule at intrinsicprograms.com> wrote: > I have that same 5way Jesse. > > Nice work, thanks for the update and pics. > Look forward to seeing you in MKE next year?! > > On Tue, Nov 3, 2020, 3:54 PM Jesse Shumaker < > jesse.laten.shumaker at gmail.com> > wrote: > > > Regardless of your disposition, there's one victory we can all celebrate > > today: my struggle against the adhesive (presumably 5200) securing the > > tabernacle has been overcome without any damage. I applied plenty > > of Marine Formula DeBond, waited patiently and then made iterative use > of a > > combination of knives, a wood wedge, and gentle taps with a rubber > mallet. > > I would scrape out adhesive around the edges, spray more DeBond, go do > > something else for a few minutes (I've got several other boat projects > > underway), tap the wedges/knives in a bit further and repeat the process. > > After about 45 minutes, I heard a gentle pop as the adhesive released. > > This was followed by another popping sound as I opened a frosty beverage > to > > celebrate. I still have to remove the thin layer of remaining adhesive > > residue but at least the tabernacle is free from the cabin top. I really > > appreciate all the helpful advice. Thanks! > > > > Jesse Shumaker > > S/V Zephyr > > > > On Wed, Oct 28, 2020 at 5:32 AM Jesse Shumaker < > > jesse.laten.shumaker at gmail.com> wrote: > > > > > Thanks for all the quick responses, links to articles and details of > your > > > experiences removing "the devil's glue." It really helps to have the > > > collective knowledge and research of the group! > > > > > > I ordered some Marine Formula DeBond and a razor blade scraper knife. > I > > > also made a wooden wedge and have a rubber mallet ready for some *very > > *gentle > > > taps after patiently waiting for the adhesive remover to go to work. > The > > > DeBond should get here on Friday so this will be a weekend project. > > Until > > > then, I have other boat projects underway to keep me busy when I'm not > at > > > work. > > > > > > I'll be sure to follow up this weekend and let you know the (hopefully > > not > > > gripping) conclusion. > > > > > > Jesse Shumaker > > > S/V Zephyr > > > > > > On Tue, Oct 27, 2020 at 4:42 PM David Talbot <talbotdavid50 at gmail.com> > > > wrote: > > > > > >> OK I am adding to this as I JUST got through managing a 5200-attached > > >> hatch > > >> on forward deck > > >> STRONGLY recommend you not use mallet or cutting as this can damage > the > > >> deck. > > >> DEBOND (can get via Amazon)works well and is safer > > >> Spray a good layer of the debond under one side of the tabernacle and > > wait > > >> a few minutes, then lightly tap wooden wedges into the gap. patience > > >> essential here. Spray more in and advance a little bit at a time. It > > will > > >> work, just do not force it or you will split the fiberglass. Will > need a > > >> sharp chisel to clean off the gel coat > > >> Agree that Practical Sailor article very helpful as well > > >> > > >> On Tue, Oct 27, 2020 at 3:20 PM, Michael D. Weisner < > > mweisner at ebsmed.com> > > >> wrote: > > >> > > >> > I wonder how 3M 5200 compares to adult barnacle attachment secretion > > >> which > > >> > is nearly impossible to break. > > >> > > > >> > Maybe Debond would work on barnacles! > > >> > > > >> > Mike > > >> > s/v Wind Lass ('91) > > >> > Nissequogue River, NY > > >> > > > >> > -----Original Message----- > > >> > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf > Of > > >> > Graham Stewart > > >> > Sent: Tuesday, October 27, 2020 3:07 PM > > >> > To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org> > > >> > Subject: Re: [Rhodes22-list] removing tabernacle > > >> > > > >> > Mark: I wouldn't even use it for the hull-deck joint. In fact I had > to > > >> > break the seal to remove the foredeck on my boat. I may be the only > > >> person > > >> > to ever do that but still I don't think anything is permanent. 5200 > > and > > >> > similar are incredible adhesives but if you are primarily interested > > in > > >> a > > >> > sealant where high adhesive qualities are not the highest priority > and > > >> if > > >> > there is any possibility that you might want to break the bond in > the > > >> > future, I would always seek an alternative. 3M 4200 is a very strong > > >> > adhesive but is easier to remove. > > >> > > > >> > Graham Stewart > > >> > Agile, Rodes 22, 1976 > > >> > Kingston Ontario > > >> > > > >> > > > >> > -----Original Message----- > > >> > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > > >> Behalf > > >> > Of Mark Whipple > > >> > Sent: Tuesday, October 27, 2020 10:28 AM > > >> > To: The Rhodes 22 Email List > > >> > Subject: Re: [Rhodes22-list] removing tabernacle > > >> > > > >> > I've read that if you take a strong, thin wire like piano wire you > can > > >> > slowly cut through the 5200 (AKA Devil's Glue). Don't know if > heating > > it > > >> > would help. I've never needed to try this so if you do let us know > how > > >> it > > >> > goes. > > >> > > > >> > About the only legit use I've heard of for 5200 is a hull-to-deck > > joint. > > >> > That's something that you hope you'll never have to disassemble. > > >> > > > >> > Good luck, > > >> > > > >> > Mark > > >> > > > >> > Boston, MA > > >> > > > >> > 2000 R22 *Luna Mia* > > >> > 1987 Nimble 30 *For Sale* > > >> > 1982 Com-Pac 16 *For Sale* > > >> > > > >> > On Tue, Oct 27, 2020 at 10:03 AM Graham Stewart < > gstewart8 at cogeco.ca> > > >> > wrote: > > >> > > > >> > > Where something is adhering to fiberglass with 5200 I think a > > >> > > sufficient whack to break the bond is likely to remove the gel > coat > > >> > > before the bond breaks. A whack might work for a metal to metal > bond > > >> > > but I would still be very careful especially for something like > cast > > >> > aluminum. > > >> > > > > >> > > Graham Stewart > > >> > > Agile, Rodes 22, 1976 > > >> > > Kingston Ontario > > >> > > > > >> > > > > >> > > -----Original Message----- > > >> > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] > On > > >> > > Behalf Of Ric Stott > > >> > > Sent: Tuesday, October 27, 2020 8:09 AM > > >> > > To: The Rhodes 22 Email List > > >> > > Subject: Re: [Rhodes22-list] removing tabernacle > > >> > > > > >> > > Careful wack with Rubber mallet!! > > >> > > Ric > > >> > > Dadventure > > >> > > > > >> > > Sent from my iPhone > > >> > > > > >> > > > On Oct 26, 2020, at 11:43 PM, Chris Geankoplis < > > >> > > chrisgeankoplis at gmail.com> wrote: > > >> > > > > > >> > > > ?Hey Jesse, > > >> > > > Sounds like PL5200. Strongest stuff in the world. Just about > > >> > > > impossible > > >> > > to > > >> > > > remove. You might make a hack saw frame but with the blade at 90 > > >> > > > degrees > > >> > > to > > >> > > > a normal one. Slowly cut between the cabin roof and tabernacle. > At > > >> > > > some point you can apply a rotational motion and should get it > > off. > > >> > > > You will Have an ugly scarred area. Research to see if they have > > >> > > > come up with a solvent for 5200. If so, use that rather than the > > >> > > > butchery method. Good luck. > > >> > > > > > >> > > > Chris Geankoplis > > >> > > > Enosis. > > >> > > > > > >> > > >> On Mon, 26 Oct 2020 at 21:51, Jesse Shumaker < > > >> > > jesse.laten.shumaker at gmail.com> > > >> > > >> wrote: > > >> > > >> > > >> > > >> Hi, I'm attempting to remove the mast tabernacle in order to > > >> > > >> install the Dwyer Halyard Organizer plate (part DH288). The > > three > > >> > > >> screws came out easily, but the tabernacle is still attached > very > > >> > > >> strongly with an adhesive. I don't know what adhesive was > used. > > >> > > >> The adhesive is colored white. I tried heating up the plate > > with a > > >> > > >> soldering iron and tried to squeeze in a razor but have been > > unable > > >> > to break the seal. > > >> > > >> > > >> > > >> I would appreciate any tips from the group on how to free the > > >> > > >> tabernacle from the cabin top. Thanks in advance for any > advice! > > >> > > >> > > >> > > >> Jesse Shumaker > > >> > > >> S/V Zephyr > > >> > > >> > > >> > > > > >> > > > > >> > > > >> > > > >> > > > > > -------------- next part -------------- > > A non-text attachment was scrubbed... > > Name: TabernacleRemovalBefore.JPG > > Type: image/jpeg > > Size: 48098 bytes > > Desc: not available > > URL: < > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20201103/222dac6e/attachment.jpe > > > > > -------------- next part -------------- > > A non-text attachment was scrubbed... > > Name: TabernacleRemovalAfter.JPG > > Type: image/jpeg > > Size: 38648 bytes > > Desc: not available > > URL: < > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20201103/222dac6e/attachment-0001.jpe > > > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 