< prior
Back to Month
Go to Thread
2021-03-26; 12:33:27 EDT
Member Since
2019-04-30
Posts: 151
Mike, you are a member of ROC entitled to pick what is left of my grey matter: / //"Is it normal?" /NO /"does it need lubrication"/ NO /"How much tension should be in the traveler line?" /Here is your answer. If you don't know how to adjust the slack i your continuous control line, email me if you do not get an earlier response. stan //See the original archive post
On 3/26/21 11:56 AM, Michael McKay wrote: > One last group of questions before we change the topic—I am new to my R22, > but I find my traveler very “stiff” and fairly hard to adjust without > considerable physical effort. Is that normal or does it need some > lubrication? How much tension should be in the traveler line? > > Thank you for the very informative discussion. > > On Fri, Mar 26, 2021 at 11:40 AM ROGER PIHLAJA <roger_pihlaja at msn.com> > wrote: > >> Rick, >> >> OK, here’s 2 books on sail trim >> >> Bill Gladstone, “North U TRIM”, 6th ed, (2007), North U, Madison, CT >> >> “The North U Fast Couse”, (1990), North U, Milford, CT >> >> Each of the above are textbooks as part of a North U sailing class and >> there are companion videos under the same titles. >> >> Here’s 2 more videos: >> >> Peter Bateman, “Sail Trimming Made Easy”, R129, Bennett Marine Video, >> Marina Del Ray, CA >> >> “The Shape Of Speed”, R329, Bennett Marine Video, Marina Del Ray, CA >> >> One thing you will note in all of these references is that the traveler is >> constantly adjusted to maintain the windward/leeward helm balance. The >> traveler is not a digital on/off device, it is constantly used for fine >> tuning while underway. With the traveler and the tiller both under the >> control of the helmsman, the Rhodes 22’s helm balance can be adjusted on >> the fly better than any other boat I’ve ever experienced. The GBI 29 >> Traveler has the additional advantage of having sufficient range of motion >> and responsiveness to be able to depower the rig in a gust and quickly get >> back on line after the gust has passed. If other boats could do it, they >> would! If your GBI-29 Traveler cannot do this; then, you are using it >> wrong. If you are busting your knuckles on your traveler then I can only >> imagine what unspeakable act you are attempting to commit! ? >> >> In general, racing dingies do not have as much range of traveler movement >> as our Rhodes 22’s. Since the range of movement is limited, you cannot use >> the traveler to depower the main. Some keelboats also do not have >> sufficient range of motion in the traveler. Some boats are limited by >> their traveler design, like the 2nd generation traveler on the Rhodes 22, >> which had poor ergonomics on the clam cleat placement, thus making it hard >> for the helmsman to operate without leaving his preferred hiking position >> on the windward gunnel. Some boats have sticky, poorly designed, &/or >> placed traveler tracks, thus making it impossible for the helmsman to >> constantly play with the traveler. Name the sailboats, other than the >> Rhodes 22, that you’ve sailed that combine sufficient range of traveler >> movement to be able to depower the rig, good ergonomics for the helmsman, >> fast response, and can be operated with one hand. Off the top of my head, >> I can’t think of any. Our boats are unique. >> >> The only Rhodes 22 I have access to is S/V Dynamic Equilibrium, a 1976 >> model. How about if I spot you 10 sec/nm? >> >> This thread is getting really long and very old. Can we please change the >> subject? >> >> Roger Pihlaja >> S/V Dynamic Equilibrium >> >> From: Graham Stewart<mailto:gstewart8 at cogeco.ca> >> Sent: Friday, March 26, 2021 10:37 AM >> To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> >> Subject: Re: [Rhodes22-list] [Rhodes22e-list] New Traveler Modifications - >> another alternative >> >> Rob: No, my boat did not have anything attached to the back stays that >> would >> attach to a traveler. I thought that those with the end cups were specially >> made. Otherwise, how were the cups attached? >> >> Graham Stewart >> gstewart8 at cogeco.ca >> >> >> >> >> >> >> >> -----Original Message----- >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >> Of >> Lowe, Rob >> Sent: Friday, March 26, 2021 10:25 AM >> To: 'Curtis Ruck'; 'The Rhodes 22 Email List' >> Subject: Re: [Rhodes22-list] [Rhodes22e-list] New Traveler Modifications - >> another alternative >> >> Graham, >> My first boat was a 1976 and had the traveler bar mounted between two 'bar >> end cups' that attached to the back stays. Is your boat not similarity >> equipped? I don't think there was anything special about the backstays. - >> Rob >> >> ________________________________ >> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of >> Graham >> Stewart <gstewart8 at cogeco.ca> >> Sent: Friday, March 26, 2021 10:11 AM >> To: 'Curtis Ruck' <ruckc at yahoo.com>; 'The Rhodes 22 Email List' >> <rhodes22-list at rhodes22.org> >> Subject: Re: [Rhodes22-list] [Rhodes22e-list] New Traveler Modifications - >> another alternative >> >> I have been interested in the traveler discussion. My boat (1976) didn't >> have a traveler when I got it and the mainsheet was simply attached to the >> table base in the cockpit. My backstays are not equipped to install a >> traveler and replacing the stays with new ones seemed cost prohibitive to >> me. Initially I installed a traveler between the lazerette and the cockpit >> seats. That worked well enough but made movement around the cockpit >> awkward. >> >> My latest version was to mount the traveler track to a 1" stainless steel >> tube and fasten that to my stern rail where it would seem to work in a >> manner similar to those attached to the back stays. The rail does not flex >> like the backstays would but I don't know if that is a good thing or not. >> While this system seems very strong to me I am no engineer or otherwise >> qualified to know. >> >> For those who are reluctant to pay the cost of both the backstay >> replacement >> plus the cost of the new traveler this arrangement might be worth >> considering. >> >> I like that the traveler being close to the stern rail means I don't have >> an >> additional barrier to reaching over the stern rail to lift the motor and >> that it is out of the way when sailing. I don't like the fact the it is >> awkward to reach the lee traveler line. Any thought on improvements or >> worries about this installation would be welcome. >> >> Graham Stewart >> Agile, Rodes 22, 1976 >> Kingston Ontario >> >> >> >> >> >> >> >> -----Original Message----- >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >> Of >> Curtis Ruck via Rhodes22-list >> Sent: Thursday, March 25, 2021 9:45 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] [Rhodes22e-list] New Traveler Modifications >> >> Hmm, i'll jump in and throw my two cents in, with my 1976 R22. >> >> When i'm racing in gusty 15+ knots... i am typically sitting on the side >> rails above the seat, with one hand on the tiller extension and my other >> fully gloved hand is holding the mainsheet uncleated, and i use that hand >> to either let slip the mainsheet in a strong gust, or i give and take a >> little with my hand holding the mainsheet from flying loose. I have a >> harken 3:1 windward sheeting traveler rail mounted on the back stays. I >> try to get the mainsheet as flat as possible. I would never use my >> traveler to try controlling the main for gusting, holding the uncleated >> mainsheet just feels natural, a little give, a little take, lets me feel >> like i'm riding with the wind, and it allows instant response. Though on >> long races my arms feel it. >> >> BTW, my traveler setup in the picture. I mounted the harken traveler rail >> on a 1" OD Fiberglass tube with stainless 316 mounts on each end that the >> backstays run through. Mounts are attached to the backstay with a small >> stainless tube slightly larger than the backstay diameter to reduce the >> friction wear on the backstays. I love the setup, but sometimes wish I had >> a fixed traveler rail that wasn't floating. >> >> [image: image.png] >> >> -- >> Curtis >> >> >> On Thu, Mar 25, 2021 at 8:38 PM Shawn Boles <shawn.sustain at gmail.com> >> wrote: >> >>> Oh boy, a match race! Much more enjoyable than the obscene, but >>> fascinating, America's Cup races I just watched. >>> >>> Cheers, >>> Shawn s/v Sweet Baboo (1986/2010) >>> >>> On Thu, Mar 25, 2021, 1:49 PM Rick Lange <sloopblueheron at gmail.com> >> wrote: >>>> Roger, >>>> >>>> I learned to sail and race by taking a college physical education class >>>> over 50 years ago. I've raced dinghies through keel boats, including >> the >>>> R22, and as skipper, have a few blue flags to show for it. >>>> >>>> I accept your challenge to match race R22's with the IMF and diamond >>> board. >>>> I challenge you to produce the videos you said are so common >>> demonstrating >>>> using the traveller on small sloops to dump wind during gusts >>>> that overpower while close hauled. >>>> >>>> Regards, >>>> >>>> Rick Lange >>>> >>>> >>>> On Thu, Mar 25, 2021 at 2:44 PM ROGER PIHLAJA <roger_pihlaja at msn.com> >>>> wrote: >>>> >>>>> Rick, >>>>> >>>>> We were having a discussion of mainsail trim and traveler use in >> heavy >>>> air >>>>> wherein the rig needs to be depowered in gusts and then quickly >> brought >>>>> back on line after the gust has passed. Mainsail shape for <= 10 >> knots >>>> is >>>>> considered light air and is a different subject. As you noted, the >>>> optimum >>>>> light air mainsail shape is achieved with a different traveler car >>>> position >>>>> and mainsheet tension vs heavy air. In light air, it is also much >> less >>>>> likely the rig will need to be depowered as per the original >>> discussion. >>>>> It is beyond the scope of my job description to give tutorials on >> sail >>>>> trim in all possible conditions. I suggest you take a class or go >>> racing. >>>>> Stan, >>>>> >>>>> I give up! I've tried to explain the merits of your GBI 29 Traveler >> to >>>>> the best of my ability. But, it's not working. If you want to jump >>> into >>>>> this discussion, go ahead. But, I'm done. >>>>> >>>>> Roger Pihlaja >>>>> S/V Dynamic Equilibrium >>>>> >>>>> >>>>> >> -------------- next part -------------- >> A non-text attachment was scrubbed... >> Name: image.png >> Type: image/png >> Size: 3456191 bytes >> Desc: not available >> URL: >> < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20210325/763bc9ee/a >> ttachment.png >> <http://rhodes22.org/pipermail/rhodes22-list/attachments/20210325/763bc9ee/attachment.png> >> -------------- next part -------------- >> A non-text attachment was scrubbed... >> Name: New traveller.jpg >> Type: image/jpeg >> Size: 128837 bytes >> Desc: not available >> URL: >> < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20210326/74da184f/a >> ttachment.jpg >> <http://rhodes22.org/pipermail/rhodes22-list/attachments/20210326/74da184f/attachment.jpg> >> -------------- next part -------------- >> A non-text attachment was scrubbed... >> Name: Taveller end hardware.jpg >> Type: image/jpeg >> Size: 106100 bytes >> Desc: not available >> URL: >> < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20210326/74da184f/a >> ttachment-0001.jpg >> <http://rhodes22.org/pipermail/rhodes22-list/attachments/20210326/74da184f/attachment-0001.jpg> >> -- > Michael McKay (mm.bizlist1 at gmail.com)
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 