2021-05-03; 15:15:12 EDT
Member Since
2016-12-14
Posts: 257
Jim, I didn't bother reading all of the other replies. If your problem has been solved, then you can stop reading now. I replaced my Centerboard gasket, pendant and blocks a couple of years ago. The flooring comes up quite easlily but it's helpful to remove the settee at the same time. Depending on condition, plan on replacing the sub-floor. I found that it was not marine grade and there was considerable mold and rot. If you do replace, I'd advise getting a good soaking of wood preservative on it before replacing. I purchased a gasket from the GBI plant. Stan will sell you one for about $100. It is neoprene rubber. It will need to be cut and you have your old one for a template. The key here are the hole locations. There are over 50 and they MUST be correct to line up with the FG flange on the CB trunk so you don't end up with any buckling of the gasket. If you're not comfortable doing it yourself (which I wasn't) and you are in the southern Virginia-Carolina area, take your Rhodes to the plant and have them install the gasket. (Email Stan first: stan at generalboats.com for an appointment) They will do it correctly. If you're in the DC/Maryland/Virginia area, Voilier Yachts specializes in Rhodes. Contact Chris Cowie ccowie at voilieryachts.com (he's on the List). The pendant for the CB is fairly easy as well. In my case, I just had Voilier do it at the same time as they cut out the gasket. I installed the new gasket but found that somewhere along the line, and you will find this alot, a previous owner had skimped on the hardware. Plan now to purchase 316 grade stainless bolts, fender washers and lock nuts. Best source is McMaster-Carr www.mcmaster.com. You will need two fender washers for each bolt, one for either side of gasket/flange sandwich. These are a pain in the ass to install, especially if your joints don't work as good as they used to! I have big hands so getting underneath the flange to hold the lock nuts while starting the threads was the hard part. Do not tighten down real hard. Make them all good and snug but not full tight. The following is the article I wrote (which I try to do after each of my Rhodes projects). The photos would not transfer over so I cut and pasted the text. REPLACING CENTERBOARD GASKET AND PENDANT Needless to say, with the sole and sub-floor removed it was a good time to inspect the centerboard (CB) trunk. I had suspected the gasket as a source for much of the water and dampness in the bilge. Removing the CB Cover and Gasket is fairly easy. General Boats specification calls for a ¼” x 1-1/4” -20 316 Stainless Steel Hex Bolt, locknut and 2 fender washers for each of 50+ holes. A previous owner had omitted the 100 fender washers. The gasket showed considerable dry rot and a hole in the middle of the gasket about 1” from the forward end of the cap. (Seen in the circular shaped stain in the top right photo). There were rust stains around most of the screws, so they may not have been 316 Stainless. To my amazement, I found that the SS fasteners that West Marine sells are 8-18 grade. They are really unsuitable for the marine environment. For a few cents more, you can get 316 grade if you look for it. I replaced all of the hardware with ¼” x 1-1/4” 316 SS Machine bolts, fender washers and lock nuts purchased from McMaster-Carr on line. Upon removing the CB Cover. Remove the pendant tube and clamp. Lift the CB Cover and lay it upside down and take a photo of the pendant routing for reference when re-assembling. “Respite’s” CB is the original design (same shape as rudder) and originally was configured with the 4 block lift mechanism. It was changed at some point to a single mini-block on the CB routed directly from the forward bale in the raised portion of the CB Cover, through the block to the 1” rod in the aft of the cover and through the hole leading to the pendant tube to the cockpit. (See Sketch). Whoever did this conversion did a pretty sloppy job leaving two of the original mini blocks in a cluster at the bale where the pendant is tied off. The pendant was in good shape but configuration of the pulley system had been changed, most likely during “recycling” by General Boat. One of the original two mini blocks on the trailing edge of the CB had been eliminated and both of the two blocks in the trunk cap had been eliminated (although they were still present) I obtained a replacement gasket through Chris Cowie, a Rhodie at VoilierYachts in White Plains, MD. I took my CB cap to them so they could get the bolt holes properly aligned in the right pattern. Once I had the new gasket, re-assembly of the gasket and CB Cover was the reverse. I tightened the hex screws good and snug taking care not to over tighten. Once you launch for the first time, check for leaks and torque the bolts as necessary, but always allow for future tightening. I’m in my third season (2021) and it hasn’t leaked a drop! This is a good time to paint your bilge. I did so with Petit Bilge Paint. Be sure to completely clean, scrub and rub down the bilge with the solvent recommended by Petit. I used two coats allowing to dry according to the instructions. I hope this will help you. The Rhodes is a great boat and there are many, many great sources of information. You should contact Stan Spitzer at GBI and inquire about the Owner's Co-Op Program: http://www.usedrhodes.com/owners-coop.html . He gets prickley if you didn't buy the boat from him, so you'll need to be in the program to get "factory support". Good luck. PS: It is helpful to List readers if members include a signature with Name, Location, Vessel Name and year(s). ----- Joe Dempsey s/v Respite Rhodes 22 1989/2005 Deltaville,VA -- Sent from: http://rhodes-22.1065344.n5.nabble.com/See the original archive post