< prior
Back to Month
Go to Thread
2021-05-18; 14:28:23 EDT
Member Since
2020-07-08
Posts: 278
Tom, I hear your frustrations. Keep in mind there are almost limitless engines that could be mounted... I guess that the trailer was designed with some/none weight on the transom. I had no issues last year when I got the boat far enough forward. And never any issues with the rudder and motor taken off. We did 75-85mph with no transom weight from OR to WI. I shoot for 300lbs of tounge.. I think my boat is "big boned" lolSee the original archive post
On Tue, May 18, 2021, 1:23 PM THOMAS POLISE via Rhodes22-list < rhodes22-list at rhodes22.org> wrote: > Im wondering why an expensive ( i recently paid around $4500 for this) > “custom” trailer by Triad isn’t designed to work properly. I was told by > Mike from Triad that everything is fine and that I shouldn’t be towing with > engine on rear of boat. I have a 9.9 Yamaha and there is no way I’m easily > moving that around. I was really disappointed with his response. > > > On May 18, 2021, at 1:50 PM, Graham Stewart <gstewart8 at cogeco.ca> wrote: > > > > ?Re: PBR's comment: That is the same problem I have. When I come up the > ramp the stern lowers and seems to put enormous pressure on the front of > the bunks. My boat now has permanent "dents" in the hull where the front > braces for the bunks are located. Stan says these older boats had very thn > scantlings and that later boats built by him are much less suseptable to > deforming. I have wondered about rigging something like tie down straps > attached to the stern rings ans some place forward on the trailer where I > might winch the boat forward those last few inches without using the bow > efy and having a downward pressure on the bow. Has anyone done something > like this? > > > > > > Graham Stewart > > Agile, Rodes 22, 1976 > > Kingston Ontario > > > > > > > > > > > > > > > > -----Original Message----- > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf Of PBR > > Sent: Tuesday, May 18, 2021 8:15 AM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Trailer > > > > I definitely want to hear the answer to Graham's question so standing by > > for that just adding my two cents. > > > > I have the same problem getting far enough forward. As said previously > the > > stern floats freely then when you pull the trailer forward that rocks the > > bow up but also back away from the stop. I have found this is highly > > dependent on how steep the ramp is. Steeper ramp means more problems. > > Also, the carpet on my bunks is too sticky, once the boat lays down on > it I > > can't pull it forward with the winch without fear of pulling out the bow > > eye. > > > >> On Tue, May 18, 2021 at 1:05 AM Graham Stewart <gstewart8 at cogeco.ca> > wrote: > >> > >> I am wondering what all is involved in adding another axel. Is it just a > >> matter of placing a secod axel behind the current one or do both axels > need > >> to be moved to achieve a proper balance? > >> > >> Graham Stewart > >> Agile, Rodes 22, 1976 > >> Kingston Ontario > >> > >> > >> > >> > >> > >> -----Original Message----- > >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf > >> Of Steven Alm > >> Sent: Monday, May 17, 2021 8:15 AM > >> To: The Rhodes 22 Email List > >> Subject: Re: [Rhodes22-list] Trailer > >> > >> Thomas, when I first bought my boat a quarter century ago and towed it > for > >> the first time, as soon as I hit 45mph the boat started fishtailing > wildly > >> and jerking the vehicle like crazy. Scary as h*ll! I took the motor off > and > >> lashed it to the trailer tongue and also loaded other gear as far > forward > >> as possible. That helped. But also, when the boat was in the yard (not > >> connected to the vehicle) if I climbed the boarding ladder the tongue > would > >> lift up. I’m only 165 lbs! After a couple years of this and many > attempts > >> to load the boat farther up on the trailer I finally popped for a second > >> axle to be added to the trailer. I added electric breaks too. Best > >> thousand bucks I ever spent! It now tracks like a dream without removing > >> the motor, shifting gear or anything else. It also gives me peace of > mind > >> knowing that if I blow a tire or burn a bearing I can safely pull > over. I > >> know some R22s tow just fine on single axle rigs but mine did not and > >> others, like you have had the same problem. Not all trailers are created > >> equal. If you plan to do much trailering I highly recommend this fix. > >> > >> Steve “Slim” Alm > >> S/V Fandango > >>> On Sat, May 1, 2021 at 12:17 AM <cjlowe at sssnet.com> wrote: > >>> > >>> Yes, I can see how I could have worded it better. You want the stopper > " > >>> arm" pushed all the way toward the tow vehicle . > >>> > >>> > >>> Jerry Lowe > >>> > >>> > >>> > >>> > >>> Just to clarify, when you say the bow stopper has to be all the way > back > >>>> you mean it should be retracted towards the front of the trailer—is > >> that > >>>> correct? > >>>> > >>>> Michael McKay > >>>> > >>>> Sent from my iPhone > >>>> > >>>>> On Apr 30, 2021, at 6:41 AM, Mitch Mitchell <mitchpadl at gmail.com> > >>> wrote: > >>>>> > >>>>> ?Makes sense. Thanks! > >>>>> > >>>>> > >>>>>> On Fri, Apr 30, 2021 at 2:16 AM <cjlowe at sssnet.com> wrote: > >>>>>> > >>>>>> Mitch, > >>>>>> The bow stopper has to be all the way back so the bow eye doesn't > >> hit > >>>>>> the stopper when pulling out of the water. As you start to pull the > >>>>>> trailer out of water, the boat is resting on the tip of forward end > >> of > >>>>>> the bunks and the aft end of the boat floats a foot or more above > the > >>>>>> back end of bunks. As the boat comes out, it rocks back and the bow > >> of > >>>>>> the boat raises about a foot, if you don't have the stop all the way > >>>>>> back, you will rip off the bow eye pad, or worse. > >>>>>> I like to have the bow eye pad about two inches forward of the bow > >> for > >>>>>> travel. The boat will rock almost that much in transit and there is > >> no > >>>>>> sense in beating up the bow by putting them tight together. > >>>>>> > >>>>>> Jerry Lowe > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> If that’s the case what would be the purpose of an adjustable bow > >>>>>>> stopper? > >>>>>>> > >>>>>>> Sent from my iPhone > >>>>>>> > >>>>>>>> On Apr 28, 2021, at 10:50 PM, Peter Nyberg < > peter at sunnybeeches.com > >>> > >>>>>>>> wrote: > >>>>>>>> > >>>>>>>> ?I’ll disagree a bit here. I never move my ‘bow bumper’. > >>>>>>>> I’ll put my bow as close to it as I can manage while the boat is > >>>>>>>> still > >>>>>>>> in the water. As Charles said, when the boat and trailer are > >> pulled > >>>>>>>> out > >>>>>>>> of the water, the space between the ‘bow bumper’ and the boat > >>>>>>>> will > >>>>>>>> increase. This is inevitable, and not necessarily a problem. > >> Moving > >>>>>>>> the ‘bow bumper’ closer to the boat at this point just increases > >>>>>>>> the > >>>>>>>> likelihood of damage to the boat in transit. > >>>>>>>> > >>>>>>>> Peter Nyberg > >>>>>>>> Coventry, CT > >>>>>>>> s/v Silverheels (1988/2016) > >>>>>>>> > >>>>>>>>> On Apr 28, 2021, at 10:29 PM, Charles Nieman > >>>>>>>>> <blue66corvette at hotmail.com> wrote: > >>>>>>>>> > >>>>>>>>> Thomas > >>>>>>>>> You float the boat, slide the bow bumper as far forward as > >> possible, > >>>>>>>>> tighten the boat as far to the front as possible. When you drive > >> out > >>>>>>>>> of > >>>>>>>>> the water, the boat will shift to the stern, so the key is to > keep > >>>>>>>>> it > >>>>>>>>> as close to the front as possible. After you get it out of the > >>>>>>>>> water, > >>>>>>>>> then you slide the bow bumper back to the boat to reduce bounce. > >>>>>>>>> It’s > >>>>>>>>> tricky, and I’ve had to retry a few times but it can be done. > >>>>>>>>> > >>>>>>>>> Sent from my iPhone > >>>>>>>>> > >>>>>>>>> Charles > >>>>>>>>> > >>>>>>>> > >>>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>> > >>> > >>> > >>> > >> > >> > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 