< prior
Back to Month
Go to Thread
2021-05-18; 14:40:37 EDT
Member Since
2004-10-28
Posts: 1565
Actually, 6 gals is about 36 lbs as gas is about 6 pounds per gallon.See the original archive post
On Tue, May 18, 2021 at 2:24 PM Tom Van Heule < tom.vanheule at intrinsicprograms.com> wrote: > Thanks Reuben. Great write up/recount. > To add fwiw... 6gal of gas is also about 45lbs. I'd prefer the gas be > opposite the engine for the balance. (8hp 4.strike.is about 89lbs?) > > I personally like low maintenance, a lot. > I am finding myself more energy/pollutant conscious as time goes on. I > still grill steaks. > > Fair winds , all, > > On Mon, May 17, 2021, 3:09 PM Reuben Mezrich <reuben.mezrich at gmail.com> > wrote: > > > I apologize for the delay in responding to this thread, but I’ve been > > traveling (finally took advantage of being vaccinated and it's the first > > time we’ve seen the grandkids in over a year) > > > > As Stan indicated, I had an electric outboard installed on the Rhodes 22 > > that he rebuilt for me and which was delivered on Dec 22 to me in > Sarasota > > by the team of Nick and Chris Geankoplis. > > > > I chose the ePropulsion Navy 3 engine, the E80 battery, a 20 amp charger, > > and a top mounted remote control (which Stan mounted on the port coming). > > The E80 battery (which weighs 100 lbs) was placed in the space normally > > occupied by the 15 gallon water tank and a smaller 5 gallon water tank > > shoehorned in next to the battery and its charger. This put the battery > low > > and amidships for good weight distribution. The engine, which weighs > about > > 54 lbs was mounted on the usual electric motor mount. > > > > I chose the ePropulsion over a Torqueedo because it had better specs at a > > lower cost for a more or less equivalent system. > > > > The ePropulsion Navy 3 is a 3kwatt engine, equivalent to a 6hp gas > engine. > > It weighs 54 lbs and I chose the short shaft version because the distance > > from the propeller hub to the transom clamp is the same as that distance > on > > a long shaft gasoline outboard. The battery stores ~4.1kwatt-hours and > as I > > mentioned weights 100 lbs. The 20Amp charges will bully charge the > battery > > in ~6 hours. They do sell a 40amp charger that will fully charge in 3 > hours > > > > What follows are my thoughts after using the engine for about 4 months > > > > Pro’s > > > > There is little (actually so far no) maintenance. The unit has a > brushless > > DC motor mounted in the pod at the bottom of the shaft where the > propeller > > attaches so it is water cooled and there are no moving parts except the > > propeller. > > > > No fuel or oil is required. I keep the boat in a slip which has a 120 > volt > > outlet nearby and so simply plug it in after each sail. You have to > > remember to unplug it before leaving the slip for a sail. > > > > There is good weight distribution with a 54 lb engine at the transom and > a > > 100 lb battery low and amidships > > > > The engine will push the boat at hull speed -~6knots - at least in flat > > water without much wind. > > > > It seems to have reasonable range - about 5 hours at 4 knots. It will run > > longer at lower speeds or less at higher speed for an effective range of > > about 20 miles, about what you’d get with 3 gallons of gas on a gasoline > > outboard. But to be honest I have not actually tested the full range and > > I’m reporting what the computer in the remote throttle control reports I > > would get if I pushed it all the way. > > > > The remote throttle is a pleasure to use, nicely at hand and displays > speed > > and time/distance remaining at the current speed. > > > > > > Cons > > > > It is expensive compared to a gasoline outboard. My total coast was a bit > > under $5,000 and it would have been worse but Stan passed on to me what > the > > distributor charged him. > > > > > > The biggest problem is that service and support is non-existent. The > > company is based in China. There are no service personnel in the US. > There > > is no parts depot in the US. The East Coast distributor is Mack-Boring, > > whose main business is distributing and servicing Yanmar diesel engines. > I > > purchased my unit from Mastry, located in St. Petersburg, who also mostly > > deals in Yanmar engines but also handles ePropulsion and Torqueedo > > engines. The salespeople at both Mastry and Mack-Boring have been very > nice > > and tried to answer some of my questions, but they are not service people > > and have no resources in terms of parts or engineering support. A few > > cables were missing in my original delivery and it took a month to have > it > > shipped to me from China. I expect that as the ePropulsion equipment > > becomes more popular in this country they will start stocking parts in > the > > US and perhaps even open a service office, but that's really just a hope > on > > my part. > > > > There is no equivalent of a friction control to keep the engine from > > turning. When I’m using the Rhodes tiller to steer the boat I’d like the > > engine direction to be fixed (with the prop pointing aft) but there is no > > mechanism to do that. They do sell a “locking arm” which is sort of a > > U-bolt, about 10” long that extends from the starboard side of the engine > > mount and does lock the engine but unfortunately it interferes with the > > rudder and limits its range….its a very kludgy design. > > > > There is a tiller that can be attached to the engine but it can only > angle > > up ~70 degrees from the horizontal and with the engine lowered it would > > have to angle up nearly 90 degrees to clear the transom. I plan to fix a > > tiller mount to the top of the engine, sort of how Stan affixes his > rudder > > to outboard engine coupling, to give me better control of the engine > > direction..It would be particularly useful when trying to steer in > reverse. > > > > The propeller has only two blades and there are no options for a 3 or 4 > > blade propellor. From my meager understanding of propellers I would think > > that the efficiency of the engine could be improved by a better > propeller. > > > > The bottom line is that I don’t really think the company had sailboats in > > mind when they designed the engine. > > > > So...If I had it to do over again I don’t think I’d choose an electric > > outboard again. You can get a new 9.9hp gas outboard with electric start > > that weighs about 90 lbs for about $2,500 (e.g. Tohatsu). I would imagine > > the savings in the cost of the engine would pay for at least a few years > > worth of maintenance. > > > > Reuben Mezrich > > Pelican Cove in Sarasota > > Cell: 410-499-8922 > > > > > > On Fri, May 14, 2021 at 8:48 PM stan <stan at generalboats.com> wrote: > > > > > Hi Peter, You remember Doc Reuben from Sarasota who tried to hitch a > > > test sail with you. He ended up with an epropulsion outboard we > > > installed on his Rhodes. I never got a chance to try it. But by now he > > > knows the good and the bad. You have his email address in your > > > computer. Can't think of a better reviewer to send you to. When I > told > > > him the best doctors I have run across got an engineering degree first, > > > he raised me by saying he got three engineering degrees before going > for > > > his MD. There may be some fodder there for a fresh poem if you are > still > > > at it. > > > > > > stan > > > > > > > > > On 5/14/21 4:54 PM, peter klappert wrote: > > > > I'd be glad to hear from R22 skippers who use electric outboards. > > > > Recommendations (pro & con) would be welcome. > > > > > > > > I'm also selling my Mercury 9.9 BigFoot. Very low hours, but it > needs a > > > > minor repair & professional tune-up. I'm in Palmetto, FL, and > reachable > > > at > > > > 202-821-2679. > > > > > > > > Peter Klappert > > > > s/v Aeolia (2012) > > > > > > > > > > > > *>>>>>>>>> *[image: Sailboat on Messenger]* <<<<<<<<<* > > > > > > > > *Peter Klappert5012 Bay State Road Palmetto, FL 34221* > > > > > > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 