< prior
Back to Month
Go to Thread
2021-05-21; 15:00:26 EDT
Member Since
2012-07-26
Posts: 198
For what it is worth, LOW tire pressure on the trailer will also affect the sway. Yeah, been there. Cary.See the original archive post
On Fri, May 21, 2021, 2:41 PM ROGER PIHLAJA <roger_pihlaja at msn.com> wrote: > Slim, > > As I recall, Fandango is a newer R-22 with IMF mainsail and a much fancier > interior. Your boat and trailer probably weighs more than 3100 lbs when > rigged for trailering with full tanks and the outboard mounted on the > transom. 3600 lbs wouldn’t surprise me; but, I would get it weighed to be > certain. Then, I would use the > 10% of the gross trailer weight criteria > for the minimum tongue weight. If it’s stable on the highway; then, you > have enough tongue weight and might be able to back off a little. But, > having the trailer go into a death sway on the expressway is terrifying! > So, be careful. On my boat/trailer combination, the worst case scenarios > are strong crosswinds &/or the shockwave from a passing truck. The trailer > might be nominally stable only to fail an “insult test” and go into a bad > wobble. My wife won’t allow me to have that kind of excitement! If the > present tongue weight isn’t causing some other issue, like something > rubbing or dragging on the ground, what’s the incentive for reducing the > tongue weight? > > Roger Pihlaja > S/V Dynamic Equilibrium > > Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for > Windows 10 > > From: Steven Alm<mailto:stevenalm at gmail.com> > Sent: Friday, May 21, 2021 12:50 PM > To: The Rhodes 22 Email List<mailto:rhodes22-list at rhodes22.org> > Subject: Re: [Rhodes22-list] Axle location > > This discussion has made me curious, and after seeing Todd's drawing I went > out and measured and yes, my front axle is 6" in front of what his drawing > shows, and my rear axle is 36" behind that. But Roger, you now have me > wondering if my tongue weight is too much. I haven't taken the bathroom > scale to it — and I will — but if it's more than approx. 310 lbs, wouldn't > I be able to achieve that by loading the boat a little farther back? That > would be easy to do and I could be pretty exact by positioning the bow stop > slightly rearward when I load. Thanks. > > Slim > Fandango > > On Fri, May 21, 2021 at 10:26 AM Graham Stewart <gstewart8 at cogeco.ca> > wrote: > > > Perfect. Thanks Roger. That is much simpler than what I had imagined. I > > appreciate your patience as now that I see it, it should have been > obvious > > to me. > > > > My boat has always had a full marine toilet and holding tank. When I got > > my boat about 26 years ago the holding tank was immediately behind the > > V-birth and there was no water tank on the boat nor was there any obvious > > place where one had been even though there was a deck fill. After my > > rebuild I replaced the old metal, and leaking, holding tank with a > smaller > > poly tank in the same place as the previous tank had been but I also had > > room for my battery. Because I just day sail in recent years my holding > > tank is empty all of the time - so no weight there to speak of. > > > > For water I am using a removable jerry can that stays below the sink > > midship on the starboard side. Again, there is rarely any water in it. > When > > I need water I just take the can up to my house and fill what I need. I > > have a deck fill installed but it is easier to just fill the tank given > > that my boat is docked in front of my house. > > > > Where is your water tank located? > > > > Graham Stewart > > Agile, Rodes 22, 1976 > > Kingston Ontario > > > > > > > > > > > > > > > > -----Original Message----- > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf > > Of ROGER PIHLAJA > > Sent: Friday, May 21, 2021 8:03 AM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Axle location > > > > Graham, > > > > You will need a bathroom scale that reads up to 350 lbs and 2 hydraulic > > bottle jacks. First load up the boat as you will have it for trailering > it > > down the road. In my case, that includes a full tank of fuel, empty > > porta-potti, full water tank, and of course, the outboard mounted on the > > transom. I assume you have a tongue jack? If not, you will need a jack > > stand or something to support the end of the tongue on top of the scale. > > Start by putting the tongue jack on top of the scale and get a tongue > > weight measurement. The rule of thumb for tongue weight is about 10% of > > the gross trailer weight in order to have stability. Figure your boat > and > > single axle trailer weighs about 3100 lbs. So, you need about 310 lbs of > > tongue weight. Now, jack the trailer frame up from the same spot on both > > sides. I would start immediately behind the tires. Get the trailer’s > > frame at approximately the same level as when it was supported by the > > tires. Note that you will probably have to remove the tires to get it > low > > enough. Now, measure the tongue weight as before. It should be greater > > than before. Keep moving the jack points aft until you find a spot on > the > > frame that gives you about 310 lbs of tongue weight. That’s where your > > single axle needs to be moved to. > > > > By the way, your R-22 is the same year as mine. The early R-22’s had > > porta-potti’s, not marine toilets and holding tanks. Where is your water > > tank located? > > > > Roger Pihlaja > > S/V Dynamic Equilibrium > > > > > > > > Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for > > Windows 10 > > > > From: Graham Stewart<mailto:gstewart8 at cogeco.ca> > > Sent: Thursday, May 20, 2021 9:59 PM > > To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> > > Subject: Re: [Rhodes22-list] Axle location > > > > Thanks to all for their suggestions. It seems that the best solution for > > me would be to have the axle moved back. I don't trailer enough to > justify > > the second axle and the other option to add weight to the tongue seem to > me > > to be a workaround rather than a fix and moving the boat forward is both > > very difficult and damaging to the hull. The area immediately aft of the > > V-birth hold my holding tank and battery, not my water tank, so > obviously > > I am not going to keep my holding tank full permanently. > > > > The big question for me now is to determine exactly how far aft I will > > have the axle moved. If anyone can suggest how I might determine that > > distance I would be grateful to hear your suggestions. > > > > Graham Stewart > > Agile, Rodes 22, 1976 > > Kingston Ontario > > > > > > > > > > > > > > -----Original Message----- > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf > > Of ROGER PIHLAJA > > Sent: Thursday, May 20, 2021 5:20 PM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Axle location > > > > Graham, > > > > Assuming you have a 15 gallon water tank mounted at the aft end of the > > V-berths, filling it would add ~125 lbs. This additional weight would be > > located at about the front end of the bunks on the trailer. Because the > > weight is not located right on the end of the tongue, you will not see > the > > full 125 lbs as additional tongue weight. On S/V Dynamic Equilibrium and > > my Lil Dude trailer, filling the water tank adds about 48 lbs of tongue > > weight. The rest of the 125 lbs is loaded onto the trailer wheels > because > > of the location of the water tank. If the tongue weight situation on > your > > trailer is causing marginal stability; this extra 48 lbs may help. It > > certainly won’t hurt. > > > > Roger Pihlaja > > S/V Dynamic Equilibrium > > > > Sent from my iPhone > > > > > On May 20, 2021, at 4:59 PM, Rick Lange <sloopblueheron at gmail.com> > > wrote: > > > > > > ?Graham, > > > > > > Fill your water tank. > > > > > > Regards, > > > > > > Rick Lange > > > > > > > > >> On Thu, May 20, 2021 at 4:54 PM ROGER PIHLAJA <roger_pihlaja at msn.com> > > wrote: > > >> > > >> Graham, > > >> > > >> Whatever the reference point or the measurement, the fact that your > > tongue > > >> weight is too low tells you everything you need to know. If you don’t > > want > > >> to just live with it, your options are: move the single axle backward > on > > >> the trailer, add a 2nd axle behind the 1st, move the boat forward on > the > > >> trailer, or add weight to the tongue. > > >> > > >> Roger Pihlaja > > >> S/V Dynamic Equilibrium > > >> > > >> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for > > >> Windows 10 > > >> > > >> From: Graham Stewart<mailto:gstewart8 at cogeco.ca> > > >> Sent: Thursday, May 20, 2021 12:50 PM > > >> To: 'The Rhodes 22 Email List'<mailto:rhodes22-list at rhodes22.org> > > >> Subject: Re: [Rhodes22-list] Axle locattion > > >> > > >> Sorry for the confusion. Because all of the other dimensions matched > the > > >> drawing I used the distance from the axle to the back because it was > the > > >> easiest measurement forgetting that others might have a different > > >> structure. > > >> > > >> The distance between the center of the axle and the point where the > > >> extension enters the trailer is 165" while that distance on the > drawing > > is > > >> 172" > > >> > > >> Graham Stewart > > >> gstewart8 at cogeco.ca > > >> > > >> > > >> > > >> > > >> > > >> > > >> -----Original Message----- > > >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > > Behalf > > >> Of > > >> Lowe, Rob > > >> Sent: Thursday, May 20, 2021 12:33 PM > > >> To: The Rhodes 22 Email List > > >> Subject: Re: [Rhodes22-list] Axle locattion > > >> > > >> I agree with Todd that the reference point should be the center of the > > ball > > >> socket. That's where the tongue weight is measure and where the > towing > > >> force is applied. - Rob > > >> > > >> > > >> ________________________________ > > >> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > > Todd > > >> Tavares <tavares0947 at gmail.com> > > >> Sent: Thursday, May 20, 2021 11:11 AM > > >> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > >> Subject: Re: [Rhodes22-list] Axle locattion > > >> > > >> By looking at these old drawings, I guess the datum point/benchmark > > really > > >> should have been the center of the ball socket, which would have > better > > >> standardized the tongue weight (and balance). That would have to > assume > > the > > >> coupler and extension lengths were somewhat uniform. > > >> > > >> Measuring the axle position from the rear of the trailer frame or the > > rear > > >> bunk support is not the best reference. > > >> Also, the angles of the bunks are a little off (I was never good at > > trig). > > >> Thankfully my carpenter's calculator has a rise over run function. The > > >> angles for the bunks are closer to 22.5° in the rear and 37° in the > > front > > >> (from horizontal). > > >> > > >> I seemed to remember there was approximately a 6" difference in axle > > >> positions between owners' trailers, but most reported the more > rearward > > >> dimension so I changed the drawing. There may be early drawings of the > > >> trailer in the archives before I edited the drawing which show the > > forward > > >> measurements..but I do not know. > > >> > > >> Todd T. > > >> > > >>> On Thu, May 20, 2021, 10:46 AM Cary Tolbert <retiredtoby at gmail.com> > > wrote: > > >>> > > >>> Graham, my boat is an '86 and the trailer that came with the boat is > a > > >>> Triad.. Therefore I must assume the trailer is an 86 as well. I just > > >>> measured from the end of the trailer to the center of the axle and it > > is > > >> , > > >>> DRUM ROLL . . . . . . . . . 75 1/2 inch. Sorry to add to the > > confusion.. > > >>> My front end measurements may also be off. I had the extension bar > > >> replaced > > >>> and last year added a braking system which added to the length of the > > >>> extension with a brake actuator. Mike is the second generation in > the > > >>> trailer company and I am sure the trailer has evolved over the years. > > >> You > > >>> know that Stan is always tinkering with something. I think my trailer > > was > > >>> manufactured in Connecticut . The newer trailers are made in NC. > > >>> > > >>> Best of luck > > >>> Cary > > >>> > > >>> On Thu, May 20, 2021 at 9:33 AM Graham Stewart <gstewart8 at cogeco.ca> > > >>> wrote: > > >>> > > >>>> I just measured the location of my axle and compared it to the > > drawings > > >>>> prepared by Todd and found that my axle is 7" forward of what the > > >>> drawings > > >>>> specify. That strikes me as a pretty significant difference. I am > > >>> wondering > > >>>> if the others who have found it impossible to get their boats far > > >> enough > > >>>> forward might also measure the distance between the back of their > > >> trailer > > >>>> to the center of the axle to see if this is the reason for the > > >>> difficulty. > > >>>> The drawing stipulates that this distance should be 70" but mine is > > >> 77". > > >>>> > > >>>> Does anyone know whether this dimension changed at some time between > > >>> older > > >>>> and newer iterations of the boat? > > >>>> > > >>>> > > >>>> Graham Stewart > > >>>> Agile, Rodes 22, 1976 > > >>>> Kingston Ontario > > >>>> > > >>>> > > >>>> > > >>> > > >> > > >> > > > > > > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 