< prior
Back to Month
Go to Thread
2021-07-27; 12:33:44 EDT
Member Since
2002-07-21
Posts: 2852
Would not AL plate work? Just a little thicker. Always see masts with SS and AL together so metals seem ok together. Alot simpler to work with. Am I incorrect?See the original archive post
On Tue, Jul 27, 2021, 11:00 AM mweisner <mweisner at ebsmed.com> wrote: > I use SHARP cobalt (Kobalt) bits in a drill press turning 1600 RPM, max, > WITH cutting oil. Go slowly, keep the drill at right angles to the material > and peck regularly (withdraw to clean flutes). If you really have trouble > with 316, buy 303/304 stainless and save $$ on the material and drills (use > HSS bits). 316 is recommended in marine environments for corrosion > resistance but if it is typically inside the cabin or lazarette it will > help.Mike > s/v Wind Lass ('91) > Nissequogue River, NYI'd rather be sailing ⛵ > -------- Original message --------From: Cary Tolbert < > retiredtoby at gmail.com> Date: 7/27/21 11:33 AM (GMT-05:00) To: The > Rhodes 22 Email List <rhodes22-list at rhodes22.org> Subject: Re: > [Rhodes22-list] Unbolted track Mike, 316 s/s is very difficult to drill. > What tools do you have to cut anddrill 1/4 inch of the 316 stainless > steel?Just curious. This info could give some of us hope.CaryS/V Whisper > '86On Tue, Jul 27, 2021 at 11:25 AM mweisner <mweisner at ebsmed.com> > wrote:> I typically use 1/4" thick 316 stainless steel sheets. The size > varies> depending on the load from 1" x 2" strips for small hardware to 12" > x 12"> sheet stock ($130 at McMaster) for the mast crane cleat. One easily > found> source is McMaster Carr (> > https://www.mcmaster.com/metals/stainless-steel/shape~sheet-and-bar/corrosion-resistant-316-stainless-steel-6/thickness~1-4/).> > An image of the link is attached at the end of the email.> Mike> s/v Wind > Lass ('91)> Nissequogue River, NYI'd rather be sailing ⛵Please consider > the> environment before printing this email.> -------- Original message > --------From: Jesse Shumaker <> jesse.laten.shumaker at gmail.com> Date: > 7/26/21 11:28 AM (GMT-05:00) To:> The Rhodes 22 Email List < > rhodes22-list at rhodes22.org> Subject: Re:> [Rhodes22-list] Unbolted track > Just curious for those that have added> backing plates in certain > scenarios,what material have you used for> this?I've used steel sheet metal > from Home Depot that I cut to size with> anangle grinder and painted with > Rustoleum primer and paint> beforeinstallation. I didn't find stainless > steel sheet metal at the> hardwarestore or home improvement stores. I > don't recall the> gauge/thickness thatI used. I also used fender washers > on top of the> backing plates. I'veadded backing plates for the bow cleat, > two chocks> that I installed towardsthe bow, a flip up midship cleat that I > installed,> as well as the throughbolts for the anchor roller mount... so > far so> good.Jesse ShumakerS/V ZephyrOn Mon, Jul 26, 2021 at 9:48 AM > Michael D.> Weisner <mweisner at ebsmed.com>wrote:> I agree with Stan.>> The > track was> designed to support the stresses of the jib car. The forces> > experienced in> such use are directed more fore and aft, for which the > track> is secured> properly. A track mounted cleat, whether for spring line > or> docking,> exerts significant forces upward and side to side, for which > the> track is> not well suited. Such applications will likely result in > damage to> the> track, as you have found. Lastly, the track may fail if > significant> force> is applied, simply due to its age, which is not a > necessarily a> design> flaw.>> By the way, I use the foredeck mounted > docking cleat as part of my> mast> crane system. I have through bolted and > spread the transmitted forces> using> a backing plate to accommodate the > nearly 500 lbs of vertical force> that is> applied by the winch at the > start and end of the mast erection> process.> This is quite different than > the original purpose of the deck> mounted> docking cleat which was designed > to sustain mostly lateral> (horizontal)> forces when docked or moored.>> > Please do not assume that any> fixture will withstand forces outside of > its> design parameters and> remember to account for changes due to age of > the> device and boat.>> Mike>> s/v Wind Lass ('91)> Nissequogue River, NY>> > -----Original Message----->> From: Rhodes22-list < > rhodes22-list-bounces at rhodes22.org> On Behalf Of>> THOMAS POLISE via > Rhodes22-list> Sent: Monday, July 26, 2021 10:28 AM> To:> Lewin < > lewin at mail.com>> Cc: stan <stan at generalboats.com>; The Rhodes 22> Email > List <> rhodes22-list at rhodes22.org>> Subject: Re: [Rhodes22-list]> > Unbolted track>> It was being used as a spring line when it broke track>> > >> On Jul 26, 2021, at 9:50 AM, Lewin <lewin at mail.com> wrote:> >> > If > a> track mounted cleat were only used for bow and stern spring lines> would > it> be less likely to fail?> >> > ------------------> > Bernard> >> >> > On > Jul> 25, 2021, at 9:27 PM, THOMAS POLISE via Rhodes22-list <>> > rhodes22-list at rhodes22.org> wrote:> >> > I only posted because there> > were previous posts about mounting cleats> on the track. I have no> > complaints about the boat and enjoy everything> about it. I know now, the> > hard way, not to mount cleats on the tracks and> wanted to make others> > aware. I will repair and continue on enjoying> everything about the boat.> > No disrespect was intended, Stan, and I will> continue to appreciate> > everything you did to create this incredible boat.> >> >> On Jul 25, 2021,> > at 6:47 PM, stan <stan at generalboats.com> wrote:> >>> >> > >> My O my, I> > am flattered when those Rhodies who praise the Rhodes> engineering get> > pleasure out of finding what they think is a flaw.> >>> >> In the Rhodes > 50> plus years, I have not heard of a single genoa track> pull off - when > used> for what it was designed to do; carry the load of the> giant 175 > genoa> sheets. That load is carried by a great number of machine> screws; > more> than sufficient to carry the shear loading placed on them. Of> > course Todd> did not mean they should be bolted on to the gel coat. But I> > think his> comment that "I've found more than a few questionable things> > which needed> to be properly "re"engineered." is gratuitously > disingenuous.> Personally> my over the hill engineering mind would think it > silly to mount> docking> cleats to genoa tracks. Even if those tracks had > long enough> machine screw> passing all the way through the outerside of > the hull and had> fender> washers and lock nuts on them, those shiftable > docking cleats would>> distort the thin edges of the genoa tracks making > the genoa cars a chore> or> even impossible to adjust.> >> If you want to > put on docking cleats,> mount them to the boat proper.> You want a spring > line cleat, don't use it> for a docking cleat. You want a> boat engineered > for docking? Have I got a> boat to sell you. No hands, no> straps, just > three little docking eyes. See> attachment. Guaranteed to hold> for any > winds. Just stop putting moving> docking cleats where they are not> invited > to go.> >>> >> stan> >>> >>>> >>>> On 7/25/21 12:00 PM, THOMAS POLISE via > Rhodes22-list wrote:> >>> I> found that there are no nuts or nut plates, > just curious if anyone> else> had a similar situation.> >>>> >>>>> On Jul > 25, 2021, at 11:47 AM, Todd> Tavares <tavares0947 at gmail.com>> wrote:> > >>>>>> >>>>> Those are machine> screws. There should be nuts underneath or > nut> >>>>> plates embedded in> the rail under the gelcoat.> >>>>>> >>>>> > But it wouldn't surprise me if> the machine screws were just> >>>>> > threaded into wood or even threaded> into epoxy. I've found more> >>>>> > than a few questionable things which> needed to be properly> > "re"engineered.> >>>>> Let us know what you find> once you dig into this > problem.> >>>>>> >>>>> Todd T.> >>>>>> >>>>>> On> Sun, Jul 25, 2021, 11:10 > AM Rick Lange <sloopblueheron at gmail.com>>> wrote:> >>>>>>> >>>>>> Hi > Thomas,> >>>>>>> >>>>>> Would you prefer gelcoat> damage?> >>>>>>> >>>>>> > Never mount a dockline holding cleat without a> backing plate.> >>>>>>> > >>>>>> Regards,> >>>>>>> >>>>>> Rick Lange> >>>>>>>> >>>>>>> >>>>>> On Sun, > Jul 25, 2021 at 11:02 AM THOMAS POLISE via> Rhodes22-list> >>>>>> < > rhodes22-list at rhodes22.org> wrote:> >>>>>>>> >>>>>> Anyone else notice > that the jib track is just put in without> >>>>>>> bolts. I added cleat to > track which was yanked out in high winds.> >>>>>>>> >>>>>> -------------- > next part -------------- A non-text attachment was>> >>>>>> scrubbed...> > >>>>>> Name: IMG_0041.jpg> >>>>>> Type: image/jpeg>> >>>>>> Size: 763976 > bytes> >>>>>> Desc: not available> >>>>>> URL: <>> >>>>>>> >>>>>> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20210725/c> > >>>>>> 07b3fde/attachment.jpg> >>> .> >>> >> > <6221802_20170501145922633_1_XLARGE> 3.jpg>> >>>> -------------- next part > --------------> A non-text attachment was scrubbed...> Name: > Screenshot_20210727-111606_Chrome.jpg> Type: image/jpeg> Size: 339078 > bytes> Desc: not available> URL: <> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20210727/ad515376/attachment.jpg> > >> > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: 20210718_194050.jpg > Type: image/jpeg > Size: 3134887 bytes > Desc: not available > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20210727/5a91ffa8/attachment.jpg > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 