< prior
Back to Month
Go to Thread
2021-10-20; 13:31:25 EDT
Member Since
2013-07-01
Posts: 436
Thanks Todd I’m usually by myself also. I love the idea of the electric winch with a remote - let us know how that goes. So far I have not had sideways leaning issues that couldn’t be controlled easily from the crane as the mast is on the way up or down - even in some pretty heavy wind. I will be lowering the mast this Saturday while on the mooring so that when I motor over to the ramp at dusk, I can haul-it and go - Shhhh! - long silly story about municipal permits, trailers and tow vehicles. Ric Richard F. Stott, AIA, LEED AP ric at stottarchitecture.com O -631-283-1777 C- 516-965-3164See the original archive post
> On Oct 20, 2021, at 11:05 AM, Todd Tavares <tavares0947 at gmail.com> wrote: > > Ric, > > It must be that the front lower stays attached with the chain extensions > are to keep the mast from leaning beam wise?? > > I have a self-made system and attach the forward lowers to the crane pole, > and have wondered the same thing. > > I use baby stays attached to eyelets on the mast below the spreader > brackets to keep the mast in line. This method was outlined in one of the > early GB instructions. My system utilizes the trailer winch cable attached > to the crane pole. The baby stay lines run under the cabintop handrail aft > of the center mount fitting then forward and tied off to the trailer tower > next to the winch with a tautline hitch. I can easily adjust the tension in > flight, and if the mast tries to lean sideways while cranking, I can just > put a bit of pressure down on the opposite baby stay and bring the mast > back/keep it in line. > > I have purchased a small at electric winch at Harbor Freight that I will > try next spring > It has a remote fob so I can stand on the foredeck and control the mast by > and foresail/furler without having to stay at the winch. It should make the > process much easier single handed...hopefully. > > Todd T > > On Wed, Oct 20, 2021, 10:01 AM Ric Stott <ric at stottarchitecture.com> wrote: > >> GM List >> Since I owned the boat in 2013, I have used friends and family for my mast >> crane. >> Manipulating it without a crane is not as difficult with a continental rig >> because it’w lighter without the main sail attached. >> Now - I have a home made crane that I bought in NJ, and used without any >> guidance. >> I used it the first time at the end of 2020 to lower the mast. >> Intuitively - I hooked the froward-lowers to the crane and left the >> aft-lowers connected to the chainplates. >> Worked like a charm! >> I made the same connections to raise the mast this spring - again - no >> problem. >> I don’t understand the logic of connecting the aft-lowers to the crane and >> the need for extenders for the forward-lowers. >> Can someone fill me in? >> Ric >> Dadventure >> HBNY >> >> Richard F. Stott, AIA, LEED AP >> ric at stottarchitecture.com >> O -631-283-1777 >> C- 516-965-3164 >> >> >> >>> On Oct 19, 2021, at 10:02 PM, Wilson Cook via Rhodes22-list < >> rhodes22-list at rhodes22.org> wrote: >>> >>> The previous owner told me the chains on the list needed to be one link >> short. But I could not for the life of me get the pin in the headstay >> chainplate. Lowered it put in second link-closer but no cigar. Lowered >> again-put in third link and was able to crank it down far enough. If crank >> handle was parallel to deck instead perpendicular would have had another >> turn. >>> >>> As I mentioned earlier I think something was binding at the masthead >> because when it popped the headstay was looser. >>> >>> Sent from my iPhone >>> >>>> On Oct 19, 2021, at 12:18 AM, rhodes22-list-request at rhodes22.org wrote: >>>> >>>> Send Rhodes22-list mailing list submissions to >>>> rhodes22-list at rhodes22.org >>>> >>>> To subscribe or unsubscribe via the World Wide Web, visit >>>> http://rhodes22.org/mailman/listinfo/rhodes22-list >>>> or, via email, send a message with subject or body 'help' to >>>> rhodes22-list-request at rhodes22.org >>>> >>>> You can reach the person managing the list at >>>> rhodes22-list-owner at rhodes22.org >>>> >>>> When replying, please edit your Subject line so it is more specific >>>> than "Re: Contents of Rhodes22-list digest..." >>>> >>>> >>>> Today's Topics: >>>> >>>> 1. Re: Live from Annapolis this morning (Tom Van Heule) >>>> 2. Help (Chris Geankoplis) >>>> 3. Re: Stan at the show (Chris Geankoplis) >>>> 4. Re: Stan at the show (Mark Wynn) >>>> 5. Re: Stan at the show (Chris Geankoplis) >>>> 6. Re: I?m a Rhodie (Chris Geankoplis) >>>> 7. Re: Help (Michael Corley) >>>> 8. Re: I?m a Rhodie (Stephen Staum) >>>> 9. Re: Help (Chris Geankoplis) >>>> 10. Re: Bimini Car attachment (C. Robert Lester) >>>> 11. First time (Wilson Cook) >>>> 12. Re: First time (Lowe, Rob) >>>> 13. Re: First time (Peter Nyberg) >>>> 14. Re: First time (ROGER PIHLAJA) >>>> 15. Re: First time (Wilson Cook) >>>> 16. Re: First time (Jesse Shumaker) >>>> 17. Re: First time (Peter Nyberg) >>>> 18. Re: First time (Lowe, Rob) >>>> 19. Rudder cheek plate (Matt Wilson) >>>> 20. Re: Rudder cheek plate (Todd Tavares) >>>> 21. Re: Rudder cheek plate (Matt Wilson) >>>> 22. Re: Rudder cheek plate (Michael D. Weisner) >>>> >>>> >>>> ---------------------------------------------------------------------- >>>> >>>> Message: 1 >>>> Date: Fri, 15 Oct 2021 18:34:40 -0500 >>>> From: Tom Van Heule <tom.vanheule at intrinsicprograms.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Live from Annapolis this morning >>>> Message-ID: >>>> <CAEqJHY5LLMDyswRbCr9-Z=tE7xwKOZJ383pegVar2dtuJE99YQ at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> And all of us!!! >>>> >>>>> On Fri, Oct 15, 2021, 2:48 PM Graham Parker <gramille at tds.net> wrote: >>>>> >>>>> Please say hi to Stan from Vermont Graham! >>>>> G >>>>> Sv.00Sailin >>>>> >>>>> Sent from my iPhone >>>>> >>>>>> On Oct 15, 2021, at 12:09 PM, Chris Geankoplis < >>>>> chrisgeankoplis at gmail.com> wrote: >>>>>> >>>>>> ?Charles, >>>>>> I wasn't going to go to the show because General Boats was >> not >>>>>> listed. But now I see that you are there! I'm on my way down and >> should >>>>>> be there in an hour and a half or less! Looking forward to seeing you >>>>>> guys. I'm in the states only a few days before returning to Greece so >>>>> this >>>>>> is a great way to spend some time. >>>>>> Chris Geankoplis >>>>>> >>>>>> >>>>>> >>>>>>> On Fri, Oct 15, 2021 at 10:31 AM Charles Gabriel < >>>>> charles.gabriel at gmail.com> >>>>>>> wrote: >>>>>>> >>>>>>> The folks from the Youtube channel "Acorn To Arabella" held a >>>>>>> live feed from the show this morning, and near the end they just >>>>>>> happened to walk by the General Boats exhibit. You can watch >>>>>>> it here: >>>>>>> https://youtu.be/498a2IpwfAc?t=3972 >>>>>>> >>>>> >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 2 >>>> Date: Fri, 15 Oct 2021 23:07:58 -0400 >>>> From: Chris Geankoplis <chrisgeankoplis at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: [Rhodes22-list] Help >>>> Message-ID: >>>> <CADNTwiWZ_AjEddR_w_m3z33OCEci-QnysCQFQtABYJiCZBRV9w at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Just wanted to put it out. If anyone isn?t tied up and is able to attend >>>> the boat show, might I suggest spending a few hours at the show and >> perhaps >>>> some time with Stan. I think there was someone who was supposed to help >> but >>>> didn?t show. Doing the show single handed at 95 is more than he can >> handle >>>> by himself. I?ve got to return to Greece otherwise I?d do it myself. >>>> Anyway, if you can spare a few hours Saturday or Sunday that would be >>>> great. >>>> Chris Geankoplis >>>> ENOSIS >>>> >>>> ------------------------------ >>>> >>>> Message: 3 >>>> Date: Fri, 15 Oct 2021 23:16:50 -0400 >>>> From: Chris Geankoplis <chrisgeankoplis at gmail.com> >>>> To: Rod Ellner <rodellner at mac.com>, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Stan at the show >>>> Message-ID: >>>> <CADNTwiVARD1HbFctbEjU28g6c9j4MaJgMrgQO1=Zx0pFu0Jucg at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Ah, the journal will eventually get posted. I ran head on into >>>> Greek/Turkish bureaucracy so convoluted that I had to fly back to the >> US to >>>> get it fixed. Headed to Greece now. Let you all how it turns out or if I >>>> need bail money. >>>> >>>> Chris Geankoplis >>>> ENOSIS >>>> >>>> On Fri, Oct 15, 2021 at 7:06 PM Rod Ellner via Rhodes22-list < >>>> rhodes22-list at rhodes22.org> wrote: >>>> >>>>> Chris. Thanks for stopping by Annapolis. We need to hear your Rhode >>>>> Rhodes story >>>>> >>>>> Welcome home! >>>>> >>>>> Rod and Mary >>>>> >>>>> Sent from my iPhone >>>>> >>>>>> On Oct 15, 2021, at 3:54 PM, Chris Geankoplis < >> chrisgeankoplis at gmail.com> >>>>> wrote: >>>>>> >>>>>> ?Bill Wickman and I stopped by to see Stan. I would encourage any >>>>> owners to >>>>>> drop by maybe ?testify? to interested buyers. I think Stan could use a >>>>> bit >>>>>> of company. Working a show like this is a challenge for someone half >> my >>>>>> age. >>>>>> >>>>>> Chris Geankoplis >>>>>> Enosis >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 4 >>>> Date: Sat, 16 Oct 2021 10:51:03 +0000 (UTC) >>>> From: Mark Wynn <markwynn at verizon.net> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org>, Rod Ellner >>>> <rodellner at mac.com> >>>> Subject: Re: [Rhodes22-list] Stan at the show >>>> Message-ID: <1408987542.1546022.1634381463595 at mail.yahoo.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Good luck with the Greeks and Turks. Let us know if we should send a >> cake with hack saw blade included.?Mark WynnSailing ?Windchimes?? on >> Magothy River, MD >>>> >>>> >>>> Sent from the all new AOL app for iOS >>>> >>>> >>>> On Friday, October 15, 2021, 11:17 PM, Chris Geankoplis < >> chrisgeankoplis at gmail.com> wrote: >>>> >>>> Ah, the journal will eventually get posted. I ran head on into >>>> Greek/Turkish bureaucracy so convoluted that I had to fly back to the >> US to >>>> get it fixed. Headed to Greece now. Let you all how it turns out or if I >>>> need bail money. >>>> >>>> Chris Geankoplis >>>> ENOSIS >>>> >>>> On Fri, Oct 15, 2021 at 7:06 PM Rod Ellner via Rhodes22-list < >>>> rhodes22-list at rhodes22.org> wrote: >>>> >>>>> Chris.? Thanks for stopping by Annapolis.? We need to hear your Rhode >>>>> Rhodes story >>>>> >>>>> Welcome home! >>>>> >>>>> Rod and Mary >>>>> >>>>> Sent from my iPhone >>>>> >>>>>> On Oct 15, 2021, at 3:54 PM, Chris Geankoplis < >> chrisgeankoplis at gmail.com> >>>>> wrote: >>>>>> >>>>>> ?Bill Wickman and? I stopped by to see Stan. I would encourage any >>>>> owners to >>>>>> drop by maybe ?testify? to interested buyers. I think Stan could use a >>>>> bit >>>>>> of company. Working a show like this is a challenge for someone half >> my >>>>>> age. >>>>>> >>>>>> Chris Geankoplis >>>>>> Enosis >>>>> >>>> >>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 5 >>>> Date: Sat, 16 Oct 2021 08:32:29 -0400 >>>> From: Chris Geankoplis <chrisgeankoplis at gmail.com> >>>> To: Mark Wynn <markwynn at verizon.net>, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Stan at the show >>>> Message-ID: >>>> <CADNTwiWGTu=nX-HOe-kYOaeu4quHdQVJzoM6+Tiodcg70i0_bA at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Thanks for the thought Mark. Hope you get a chance to see Stan. Just >> got an >>>> email from my Turkish ?agent?. Looks like the solution can be ? >> arranged?. >>>> I?m not going to ask. Have you guys been out on the boat? >>>> Chris Geankoplis >>>> Enosis >>>> >>>> On Sat, Oct 16, 2021 at 6:51 AM Mark Wynn via Rhodes22-list < >>>> rhodes22-list at rhodes22.org> wrote: >>>> >>>>> Good luck with the Greeks and Turks. Let us know if we should send a >> cake >>>>> with hack saw blade included. Mark WynnSailing ?Windchimes? on Magothy >>>>> River, MD >>>>> >>>>> >>>>> Sent from the all new AOL app for iOS >>>>> >>>>> >>>>> On Friday, October 15, 2021, 11:17 PM, Chris Geankoplis < >>>>> chrisgeankoplis at gmail.com> wrote: >>>>> >>>>> Ah, the journal will eventually get posted. I ran head on into >>>>> Greek/Turkish bureaucracy so convoluted that I had to fly back to the >> US to >>>>> get it fixed. Headed to Greece now. Let you all how it turns out or if >> I >>>>> need bail money. >>>>> >>>>> Chris Geankoplis >>>>> ENOSIS >>>>> >>>>> On Fri, Oct 15, 2021 at 7:06 PM Rod Ellner via Rhodes22-list < >>>>> rhodes22-list at rhodes22.org> wrote: >>>>> >>>>>> Chris. Thanks for stopping by Annapolis. We need to hear your Rhode >>>>>> Rhodes story >>>>>> >>>>>> Welcome home! >>>>>> >>>>>> Rod and Mary >>>>>> >>>>>> Sent from my iPhone >>>>>> >>>>>>> On Oct 15, 2021, at 3:54 PM, Chris Geankoplis < >>>>> chrisgeankoplis at gmail.com> >>>>>> wrote: >>>>>>> >>>>>>> ?Bill Wickman and I stopped by to see Stan. I would encourage any >>>>>> owners to >>>>>>> drop by maybe ?testify? to interested buyers. I think Stan could use >> a >>>>>> bit >>>>>>> of company. Working a show like this is a challenge for someone half >> my >>>>>>> age. >>>>>>> >>>>>>> Chris Geankoplis >>>>>>> Enosis >>>>>> >>>>> >>>>> >>>>> >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 6 >>>> Date: Sat, 16 Oct 2021 08:37:57 -0400 >>>> From: Chris Geankoplis <chrisgeankoplis at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org>, Wilson Cook >>>> <reefnsail123 at yahoo.com> >>>> Subject: Re: [Rhodes22-list] I?m a Rhodie >>>> Message-ID: >>>> <CADNTwiWF8vEFs0cJ2H_vmyPn_BbT6evCfU+wp8J4aJ6tFaBs0Q at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Welcome Wilson! You are now a member of a group of passionate, devoted >>>> (hmm sounds a bit like a cult- might be) group of men and women who >> take >>>> great joy in sailing and helping others enjoy their Rhodes. >>>> Chris Geankoplis >>>> Enosis >>>> >>>> On Fri, Oct 15, 2021 at 1:21 PM Wilson Cook via Rhodes22-list < >>>> rhodes22-list at rhodes22.org> wrote: >>>> >>>>> It?s official. My Rhodes 22 2002/2009(refurbished) is in my driveway! >>>>> This mailing list seems like a tremendous resource. Is there some >> index or >>>>> search function to be able to look up previously asked questions? >>>>> >>>>> Sent from my iPhone >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 7 >>>> Date: Sat, 16 Oct 2021 10:12:29 -0400 >>>> From: Michael Corley <michael.4591 at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Help >>>> Message-ID: >>>> <CACSd1j+k0qTKqABordYLNz45z2HHNUga9z94EiQa=SD73T63fg at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> I will be there Sunday and Monday and help haul things back to Edenton. >>>> >>>> -Mike Corley >>>> s/v Ranger >>>> Hampton Roads >>>> >>>> On Fri, Oct 15, 2021 at 11:08 PM Chris Geankoplis < >> chrisgeankoplis at gmail.com> >>>> wrote: >>>> >>>>> Just wanted to put it out. If anyone isn?t tied up and is able to >> attend >>>>> the boat show, might I suggest spending a few hours at the show and >> perhaps >>>>> some time with Stan. I think there was someone who was supposed to >> help but >>>>> didn?t show. Doing the show single handed at 95 is more than he can >> handle >>>>> by himself. I?ve got to return to Greece otherwise I?d do it myself. >>>>> Anyway, if you can spare a few hours Saturday or Sunday that would be >>>>> great. >>>>> Chris Geankoplis >>>>> ENOSIS >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 8 >>>> Date: Sat, 16 Oct 2021 10:14:36 -0400 >>>> From: Stephen Staum <snstaum at gmail.com> >>>> To: Wilson Cook <reefnsail123 at yahoo.com>, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] I?m a Rhodie >>>> Message-ID: >>>> <CAOo_Fjcj7xQMuEEmxES8CRsp0bHH0tB6d8_+87Txp+rS4XMs1Q at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Wilson, >>>> >>>> Welcome to 'da list. Let us know if you need any help or advice. >>>> >>>> >>>> *Thanks and Stay Well,* >>>> >>>> *Stephen Staum* >>>> *s/v Pinafore (my 3rd Rhodes 22)* >>>> >>>> *Needham, MA* >>>> >>>> >>>> >>>> On Fri, Oct 15, 2021 at 1:21 PM Wilson Cook via Rhodes22-list < >>>> rhodes22-list at rhodes22.org> wrote: >>>> >>>>> It?s official. My Rhodes 22 2002/2009(refurbished) is in my driveway! >>>>> This mailing list seems like a tremendous resource. Is there some >> index or >>>>> search function to be able to look up previously asked questions? >>>>> >>>>> Sent from my iPhone >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 9 >>>> Date: Sat, 16 Oct 2021 10:48:58 -0400 >>>> From: Chris Geankoplis <chrisgeankoplis at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Help >>>> Message-ID: >>>> <CADNTwiV2t-Ef4DcqnjiXmn6mc3pgF+sQu1nxSWJuho-mSwJdzQ at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> That is great Mike. We all appreciate your helping Stan! >>>> Chris Geankoplis >>>> Enosis >>>> >>>> On Sat, Oct 16, 2021 at 10:12 AM Michael Corley <michael.4591 at gmail.com >>> >>>> wrote: >>>> >>>>> I will be there Sunday and Monday and help haul things back to Edenton. >>>>> >>>>> -Mike Corley >>>>> s/v Ranger >>>>> Hampton Roads >>>>> >>>>> On Fri, Oct 15, 2021 at 11:08 PM Chris Geankoplis < >>>>> chrisgeankoplis at gmail.com> >>>>> wrote: >>>>> >>>>>> Just wanted to put it out. If anyone isn?t tied up and is able to >> attend >>>>>> the boat show, might I suggest spending a few hours at the show and >>>>> perhaps >>>>>> some time with Stan. I think there was someone who was supposed to >> help >>>>> but >>>>>> didn?t show. Doing the show single handed at 95 is more than he can >>>>> handle >>>>>> by himself. I?ve got to return to Greece otherwise I?d do it myself. >>>>>> Anyway, if you can spare a few hours Saturday or Sunday that would be >>>>>> great. >>>>>> Chris Geankoplis >>>>>> ENOSIS >>>>>> >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 10 >>>> Date: Sat, 16 Oct 2021 19:11:05 +0000 >>>> From: "C. Robert Lester" <C.Robert.Lester at dartmouth.edu> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Bimini Car attachment >>>> Message-ID: >>>> < >> BN9PR03MB61567E7B2DA124E065DBBFEDAEBA9 at BN9PR03MB6156.namprd03.prod.outlook.com >>> >>>> >>>> Content-Type: text/plain; charset="us-ascii" >>>> >>>> Found it! >>>> >>>> >> https://www.catalinadirect.com/shop-by-boat/catalina-27/canvas-covers/biminis/bimini-genoa-track-cars/ >>>> >>>> Thanks all for the feedback an pics. >>>> Bob >>>> >>>> >>>> -----Original Message----- >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of >> Todd Tavares >>>> Sent: Monday, October 4, 2021 8:46 AM >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Bimini Car attachment >>>> >>>> Bob, >>>> >>>> I'm not sure what you are asking for. >>>> A bimini car rides on the genoa track (usually). >>>> >>>> As far as the traveller car, there have been several different styles >> of traveller used over the years. Some are specific custom cars and others >> are available commercially. >>>> >>>> >>>> If you are looking for the traveller car that rides on a 1" round bar, >> original probably after 1984, it is available from rig rite. >>>> >>>> >> https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.rigrite.com%2FTravellers%2FNF_Travellers%2FRound%2520Bar%2520Travellers.php&data=04%7C01%7Cc.robert.lester%40dartmouth.edu%7Ca5fd7dcf75fc4b6555e508d98734fdec%7C995b093648d640e5a31ebf689ec9446f%7C0%7C0%7C637689484519658672%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=sKNpdcuORflc9uCgB2PgoSHMd9%2Fat1HFmajlMfbHo1A%3D&reserved=0 >>>> >>>> >>>> >>>> >>>> >>>> >>>>> On Mon, Oct 4, 2021, 12:06 AM C. Robert Lester < >> C.Robert.Lester at dartmouth.edu> wrote: >>>>> >>>>> Hello all, >>>>> Would some of you share a pic with me...I'm interested in what the >>>>> bimini car on the traveler looks like. >>>>> I'm currently trying to mate the parts I have together. >>>>> Thank you, >>>>> Bob >>>>> ('84 ORION) >>>>> >>>>> >>>>> >>>>> >>>>> >>>> -------------- next part -------------- >>>> A non-text attachment was scrubbed... >>>> Name: Screenshot_20211004-084153_Chrome.jpg >>>> Type: image/jpeg >>>> Size: 299502 bytes >>>> Desc: not available >>>> URL: < >> https://nam12.safelinks.protection.outlook.com/?url=http%3A%2F%2Frhodes22.org%2Fpipermail%2Frhodes22-list%2Fattachments%2F20211004%2F505a4da7%2Fattachment.jpg&data=04%7C01%7Cc.robert.lester%40dartmouth.edu%7Ca5fd7dcf75fc4b6555e508d98734fdec%7C995b093648d640e5a31ebf689ec9446f%7C0%7C0%7C637689484519668621%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=RXikcOHKHzQe1loq7WoFXrhKRQNp4BiSRe0T7cZ1VE4%3D&reserved=0 >>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 11 >>>> Date: Mon, 18 Oct 2021 07:57:46 -0400 >>>> From: Wilson Cook <reefnsail123 at yahoo.com> >>>> To: rhodes22-list at rhodes22.org >>>> Subject: [Rhodes22-list] First time >>>> Message-ID: <E09B1CB6-8F54-4FED-ADC1-D1841E6B752E at yahoo.com> >>>> Content-Type: text/plain; charset=utf-8 >>>> >>>> So I erected my mast for the first time yesterday. I hope there is a >> short learning curve. Took a while but I was single handed Biggest >> challenge was the headstay. Took everything I had after shortening chains >> twice. Once it was finally up and I was tensioning backstays something >> ?popped? at the masthead and then forestay was looser. >>>> >>>> Related question- there is a block and tackle across the backstays but >> there is no cleat? >>>> >>>> Sent from my iPhone >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 12 >>>> Date: Mon, 18 Oct 2021 12:17:30 +0000 >>>> From: "Lowe, Rob" <rlowe at vt.edu> >>>> To: "rhodes22-list at rhodes22.org" <rhodes22-list at rhodes22.org>, Wilson >>>> Cook <reefnsail123 at yahoo.com> >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: >>>> < >> DM6PR05MB6985FAA050B2F85FC2E6F600C1BC9 at DM6PR05MB6985.namprd05.prod.outlook.com >>> >>>> >>>> Content-Type: text/plain; charset="windows-1252" >>>> >>>> Wilson, >>>> The cleat for the backstay adjustment is on the starboard side, next to >> the chainplate. - rob >>>> >>>> ________________________________ >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of >> Wilson Cook via Rhodes22-list <rhodes22-list at rhodes22.org> >>>> Sent: Monday, October 18, 2021 7:57 AM >>>> To: rhodes22-list at rhodes22.org <rhodes22-list at rhodes22.org> >>>> Subject: [Rhodes22-list] First time >>>> >>>> So I erected my mast for the first time yesterday. I hope there is a >> short learning curve. Took a while but I was single handed Biggest >> challenge was the headstay. Took everything I had after shortening chains >> twice. Once it was finally up and I was tensioning backstays something >> ?popped? at the masthead and then forestay was looser. >>>> >>>> Related question- there is a block and tackle across the backstays but >> there is no cleat? >>>> >>>> Sent from my iPhone >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 13 >>>> Date: Mon, 18 Oct 2021 06:11:05 -0700 >>>> From: Peter Nyberg <peter at sunnybeeches.com> >>>> To: rhodes22-list at rhodes22.org >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: <E1mcSPx-000V1H-Cu at s152.servername.online> >>>> Content-Type: text/plain; charset="UTF-8" >>>> >>>> ?or it might be on the port side. >>>> >>>> Which side the tensioner get cleated to depends on how the blocks on >> the back stays are configured. Mine are set for port side cleaning, but >> General Boats put cleats on both sides, just in case. >>>> >>>> Peter Nyberg >>>> Coventry, CT >>>> s/v Silverheels (1988/2016] >>>> >>>> >>>>> On 2021-10-18, at 08:17:30 EDT, Lowe, Rob wrote: >>>>> >>>>> Wilson, >>>>> The cleat for the backstay adjustment is on the starboard side, next >> to the >>>>> chainplate. - rob >>>>> >>>>> >>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 14 >>>> Date: Mon, 18 Oct 2021 15:36:06 +0000 >>>> From: ROGER PIHLAJA <roger_pihlaja at msn.com> >>>> To: Wilson Cook <reefnsail123 at yahoo.com>, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: >>>> < >> CH2PR02MB6920B2DEB50D42D434B525BE80BC9 at CH2PR02MB6920.namprd02.prod.outlook.com >>> >>>> >>>> Content-Type: text/plain; charset="windows-1252" >>>> >>>> Hi Wilson, >>>> >>>> It helps to make a checklist and follow it. Do you have the GBI mast >> stepping system? I am not strong enough to step/unstep the mast without >> this mechanical aid. Stepping/unstopping the mast is faster if you have >> some helpers. You save the rigging/unrigging time to setup the GBI mast >> stepping system. But, if you are alone, the GBI mast stepping system makes >> it a safe, foolproof operation. >>>> >>>> The attached picture shows the OEM standard cleat for the backstay >> adjuster. This cleat is located on the transom in the starboard aft >> corner. Also shown in the picture is my improved ?Go Faster? backstay >> adjuster. The backstay tension is the primary way to adjust forestay sag. >> Forestay sag affects genoa sailshape. You want to be able to adjust it >> quickly and reproducibly. Here are the components of my backstay adjuster: >>>> >>>> >>>> 1. Harken 146 Single Big Bullet Block With Shackle >>>> 2. Harken 144 Swivel Base With 150 Cam-Matic Cam Cleat & Stand-Up >> Spring >>>> 3. 10-24UNC X 1-1/2 Inch 18/8 Stainless Steel Flat Head Phillips >> Machine Screws, Fenders Washers, & Nylock Nuts ? 4 Reqd >>>> >>>> Instead of cleating the backstay adjuster off on the OEM standard >> horned cleat on the transom, rig it thru the Harken block and cam cleat. >> Now, using a black magic marker, mark off every 6 inches on the backstay >> control line starting from when the backstay adjuster just starts to take >> up the slack in the forestay. Now, you can reproducibly adjust the tension >> in the backstay with just a flick of the wrist and a pull on the control >> line to the appropriate mark. Note, the required backstay tension to >> eliminate forestay sag in heavy air is quite high. I don?t like to leave >> the backstay tension that high when I leave the boat (think banana boat!). >> So, I slack off the backstay adjuster when I?m not actually sailing. Note, >> the Harken swivel base enables the helmsman to reach and adjust the >> backstay tension from any position in the cockpit. >>>> >>>> This discussion actually belongs in the ?Go Faster? &/or ?Furling >> Headsail Replacement? threads because it is another go faster upgrade >> associated with the genoa. >>>> >>>> Roger Pihlaja >>>> S/V Dynamic Equilibrium >>>> >>>> [cid:image002.jpg at 01D7C414.553B7930] >>>> >>>> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for >> Windows >>>> >>>> From: Wilson Cook via Rhodes22-list<mailto:rhodes22-list at rhodes22.org> >>>> Sent: Monday, October 18, 2021 7:57 AM >>>> To: rhodes22-list at rhodes22.org<mailto:rhodes22-list at rhodes22.org> >>>> Subject: [Rhodes22-list] First time >>>> >>>> So I erected my mast for the first time yesterday. I hope there is a >> short learning curve. Took a while but I was single handed Biggest >> challenge was the headstay. Took everything I had after shortening chains >> twice. Once it was finally up and I was tensioning backstays something >> ?popped? at the masthead and then forestay was looser. >>>> >>>> Related question- there is a block and tackle across the backstays but >> there is no cleat? >>>> >>>> Sent from my iPhone >>>> >>>> -------------- next part -------------- >>>> A non-text attachment was scrubbed... >>>> Name: 919EB46A00C54B95B151B34D35E652BB.jpg >>>> Type: image/jpeg >>>> Size: 192766 bytes >>>> Desc: 919EB46A00C54B95B151B34D35E652BB.jpg >>>> URL: < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20211018/7f5499a9/attachment.jpg >>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 15 >>>> Date: Mon, 18 Oct 2021 13:07:21 -0400 >>>> From: Wilson Cook <reefnsail123 at yahoo.com> >>>> To: ROGER PIHLAJA <roger_pihlaja at msn.com> >>>> Cc: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: <830884C5-A7FA-4F95-82DA-E07A302138A7 at yahoo.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Yes I have the mast hoist. I can?t imagine it would be possible >> certainly alone without it. I?m at work but I do have a vague memory of a >> cleat over there that I thought was odd. Now I know. >>>> >>>> This is a great resource. Thank you >>>> >>>> Sent from my iPhone >>>> >>>>> On Oct 18, 2021, at 11:36 AM, ROGER PIHLAJA <roger_pihlaja at msn.com> >> wrote: >>>>> >>>>> ? >>>>> Hi Wilson, >>>>> >>>>> It helps to make a checklist and follow it. Do you have the GBI mast >> stepping system? I am not strong enough to step/unstep the mast without >> this mechanical aid. Stepping/unstopping the mast is faster if you have >> some helpers. You save the rigging/unrigging time to setup the GBI mast >> stepping system. But, if you are alone, the GBI mast stepping system makes >> it a safe, foolproof operation. >>>>> >>>>> The attached picture shows the OEM standard cleat for the backstay >> adjuster. This cleat is located on the transom in the starboard aft >> corner. Also shown in the picture is my improved ?Go Faster? backstay >> adjuster. The backstay tension is the primary way to adjust forestay sag. >> Forestay sag affects genoa sailshape. You want to be able to adjust it >> quickly and reproducibly. Here are the components of my backstay adjuster: >>>>> >>>>> Harken 146 Single Big Bullet Block With Shackle >>>>> Harken 144 Swivel Base With 150 Cam-Matic Cam Cleat & Stand-Up Spring >>>>> 10-24UNC X 1-1/2 Inch 18/8 Stainless Steel Flat Head Phillips Machine >> Screws, Fenders Washers, & Nylock Nuts ? 4 Reqd >>>>> >>>>> Instead of cleating the backstay adjuster off on the OEM standard >> horned cleat on the transom, rig it thru the Harken block and cam cleat. >> Now, using a black magic marker, mark off every 6 inches on the backstay >> control line starting from when the backstay adjuster just starts to take >> up the slack in the forestay. Now, you can reproducibly adjust the tension >> in the backstay with just a flick of the wrist and a pull on the control >> line to the appropriate mark. Note, the required backstay tension to >> eliminate forestay sag in heavy air is quite high. I don?t like to leave >> the backstay tension that high when I leave the boat (think banana boat!). >> So, I slack off the backstay adjuster when I?m not actually sailing. Note, >> the Harken swivel base enables the helmsman to reach and adjust the >> backstay tension from any position in the cockpit. >>>>> >>>>> This discussion actually belongs in the ?Go Faster? &/or ?Furling >> Headsail Replacement? threads because it is another go faster upgrade >> associated with the genoa. >>>>> >>>>> Roger Pihlaja >>>>> S/V Dynamic Equilibrium >>>>> >>>>> <919EB46A00C54B95B151B34D35E652BB.jpg> >>>>> >>>>> Sent from Mail for Windows >>>>> >>>>> From: Wilson Cook via Rhodes22-list >>>>> Sent: Monday, October 18, 2021 7:57 AM >>>>> To: rhodes22-list at rhodes22.org >>>>> Subject: [Rhodes22-list] First time >>>>> >>>>> So I erected my mast for the first time yesterday. I hope there is a >> short learning curve. Took a while but I was single handed Biggest >> challenge was the headstay. Took everything I had after shortening chains >> twice. Once it was finally up and I was tensioning backstays something >> ?popped? at the masthead and then forestay was looser. >>>>> >>>>> Related question- there is a block and tackle across the backstays but >> there is no cleat? >>>>> >>>>> Sent from my iPhone >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 16 >>>> Date: Mon, 18 Oct 2021 14:19:34 -0500 >>>> From: Jesse Shumaker <jesse.laten.shumaker at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: >>>> <CAMc-3fpPOvWvYRvkEdewDpXGfHo94czkHRr-3y4Nc_5NffyP4w at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Roger, great idea on the easily adjustable backstay adjuster! >>>> >>>> Wilson, there are a number of posts with checklists for mast raising / >>>> lowering using the GB system that people have created over time. Let us >>>> know if you are looking for that and have any trouble finding examples. >>>> >>>> Jesse Shumaker >>>> S/V Zephyr >>>> >>>> On Mon, Oct 18, 2021 at 10:36 AM ROGER PIHLAJA <roger_pihlaja at msn.com> >>>> wrote: >>>> >>>>> Hi Wilson, >>>>> >>>>> It helps to make a checklist and follow it. Do you have the GBI mast >>>>> stepping system? I am not strong enough to step/unstep the mast >> without >>>>> this mechanical aid. Stepping/unstopping the mast is faster if you >> have >>>>> some helpers. You save the rigging/unrigging time to setup the GBI >> mast >>>>> stepping system. But, if you are alone, the GBI mast stepping system >> makes >>>>> it a safe, foolproof operation. >>>>> >>>>> The attached picture shows the OEM standard cleat for the backstay >>>>> adjuster. This cleat is located on the transom in the starboard aft >>>>> corner. Also shown in the picture is my improved ?Go Faster? backstay >>>>> adjuster. The backstay tension is the primary way to adjust forestay >> sag. >>>>> Forestay sag affects genoa sailshape. You want to be able to adjust it >>>>> quickly and reproducibly. Here are the components of my backstay >> adjuster: >>>>> >>>>> >>>>> 1. Harken 146 Single Big Bullet Block With Shackle >>>>> 2. Harken 144 Swivel Base With 150 Cam-Matic Cam Cleat & Stand-Up >> Spring >>>>> 3. 10-24UNC X 1-1/2 Inch 18/8 Stainless Steel Flat Head Phillips >>>>> Machine Screws, Fenders Washers, & Nylock Nuts ? 4 Reqd >>>>> >>>>> Instead of cleating the backstay adjuster off on the OEM standard >> horned >>>>> cleat on the transom, rig it thru the Harken block and cam cleat. Now, >>>>> using a black magic marker, mark off every 6 inches on the backstay >> control >>>>> line starting from when the backstay adjuster just starts to take up >> the >>>>> slack in the forestay. Now, you can reproducibly adjust the tension >> in the >>>>> backstay with just a flick of the wrist and a pull on the control >> line to >>>>> the appropriate mark. Note, the required backstay tension to eliminate >>>>> forestay sag in heavy air is quite high. I don?t like to leave the >>>>> backstay tension that high when I leave the boat (think banana >> boat!). So, >>>>> I slack off the backstay adjuster when I?m not actually sailing. >> Note, the >>>>> Harken swivel base enables the helmsman to reach and adjust the >> backstay >>>>> tension from any position in the cockpit. >>>>> >>>>> This discussion actually belongs in the ?Go Faster? &/or ?Furling >> Headsail >>>>> Replacement? threads because it is another go faster upgrade associated >>>>> with the genoa. >>>>> >>>>> Roger Pihlaja >>>>> S/V Dynamic Equilibrium >>>>> >>>>> [cid:image002.jpg at 01D7C414.553B7930] >>>>> >>>>> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for >> Windows >>>>> >>>>> From: Wilson Cook via Rhodes22-list<mailto:rhodes22-list at rhodes22.org> >>>>> Sent: Monday, October 18, 2021 7:57 AM >>>>> To: rhodes22-list at rhodes22.org<mailto:rhodes22-list at rhodes22.org> >>>>> Subject: [Rhodes22-list] First time >>>>> >>>>> So I erected my mast for the first time yesterday. I hope there is a >> short >>>>> learning curve. Took a while but I was single handed Biggest >> challenge was >>>>> the headstay. Took everything I had after shortening chains twice. >> Once it >>>>> was finally up and I was tensioning backstays something ?popped? at the >>>>> masthead and then forestay was looser. >>>>> >>>>> Related question- there is a block and tackle across the backstays but >>>>> there is no cleat? >>>>> >>>>> Sent from my iPhone >>>>> >>>>> -------------- next part -------------- >>>>> A non-text attachment was scrubbed... >>>>> Name: 919EB46A00C54B95B151B34D35E652BB.jpg >>>>> Type: image/jpeg >>>>> Size: 192766 bytes >>>>> Desc: 919EB46A00C54B95B151B34D35E652BB.jpg >>>>> URL: < >>>>> >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20211018/7f5499a9/attachment.jpg >>>>>> >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 17 >>>> Date: Mon, 18 Oct 2021 13:25:23 -0700 >>>> From: Peter Nyberg <peter at sunnybeeches.com> >>>> To: rhodes22-list at rhodes22.org >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: <E1mcZCF-003QBi-IT at s152.servername.online> >>>> Content-Type: text/plain; charset="UTF-8" >>>> >>>> Wilson, >>>> >>>> I've been puzzled all day about your problem with your forestay. I >> assume the 'challenge' you mention was getting the forestay connected to >> its chainplate at the bow. What had me scratching my head was your mention >> of shortening the chains. Shortening the chains shouldn't have any effect >> on being able to get the top of the mast far enough forward to make the >> forestay connection, unless... >>>> >>>> By any chance, do you have the chains connected to the mast crane? >>>> >>>> Peter Nyberg >>>> Coventry, CT >>>> s/v Silverheels (1988/2016) >>>> >>>>> On 2021-10-18, at 07:57:46 EDT, Wilson Cook wrote: >>>>> >>>>> So I erected my mast for the first time yesterday. I hope there is a >> short >>>>> learning curve. Took a while but I was single handed Biggest >> challenge was the >>>>> headstay. Took everything I had after shortening chains twice. Once it >> was >>>>> finally up and I was tensioning backstays something ?popped? at the >> masthead and >>>>> then forestay was looser. >>>>> >>>>> Related question- there is a block and tackle across the backstays but >> there is >>>>> no cleat? >>>>> >>>>> Sent from my iPhone >>>>> >>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 18 >>>> Date: Mon, 18 Oct 2021 20:34:17 +0000 >>>> From: "Lowe, Rob" <rlowe at vt.edu> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] First time >>>> Message-ID: >>>> < >> DM6PR05MB698545815394C03865A1E249C1BC9 at DM6PR05MB6985.namprd05.prod.outlook.com >>> >>>> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Photos always help too. Take a photo (jpeg preferred) and send it to us >> as an attachment. Having the backstay adjustment slack will also give you >> some leeway with the forestay. Once it's connected, you can tighten the >> backstays. >>>> >>>> Rob >>>> >>>> -----Original Message----- >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of >> Peter Nyberg >>>> Sent: Monday, October 18, 2021 4:25 PM >>>> To: rhodes22-list at rhodes22.org >>>> Subject: Re: [Rhodes22-list] First time >>>> >>>> Wilson, >>>> >>>> I've been puzzled all day about your problem with your forestay. I >> assume the 'challenge' you mention was getting the forestay connected to >> its chainplate at the bow. What had me scratching my head was your mention >> of shortening the chains. Shortening the chains shouldn't have any effect >> on being able to get the top of the mast far enough forward to make the >> forestay connection, unless... >>>> >>>> By any chance, do you have the chains connected to the mast crane? >>>> >>>> Peter Nyberg >>>> Coventry, CT >>>> s/v Silverheels (1988/2016) >>>> >>>>> On 2021-10-18, at 07:57:46 EDT, Wilson Cook wrote: >>>>> >>>>> So I erected my mast for the first time yesterday. I hope there is a >>>>> short learning curve. Took a while but I was single handed Biggest >>>>> challenge was the headstay. Took everything I had after shortening >>>>> chains twice. Once it was finally up and I was tensioning backstays >>>>> something ?popped? at the masthead and then forestay was looser. >>>>> >>>>> Related question- there is a block and tackle across the backstays but >>>>> there is no cleat? >>>>> >>>>> Sent from my iPhone >>>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 19 >>>> Date: Mon, 18 Oct 2021 20:24:40 -0500 >>>> From: Matt Wilson <mwhornblower at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: [Rhodes22-list] Rudder cheek plate >>>> Message-ID: >>>> <CANbEFCtCM051H5gy1GRH-HobkHn+ke+XnsV8C73EEmZdx=9PAg at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Hi everyone, >>>> >>>> I have a cracked port side rudder check plate and am wondering what is >> the >>>> best way to repair or replace it? I have a 1990 Rhodes. I am not a >> member >>>> of the GB parts club. Any help would be appreciated. Hoping to take >> care >>>> of this in the early off season ;) >>>> >>>> Matt Wilson >>>> Hornblower 2 >>>> >>>> ------------------------------ >>>> >>>> Message: 20 >>>> Date: Mon, 18 Oct 2021 21:30:39 -0400 >>>> From: Todd Tavares <tavares0947 at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Rudder cheek plate >>>> Message-ID: >>>> <CAB-twMP0BBZvGh7rJCWBUj_upHpqp-NNrT5uSohkip1oG8K=BA at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Matt, >>>> >>>> I would suggest buying some black UHMWPE and fabricating two new cheek >>>> plates yourself. >>>> You could also try to find a plastics production shop to fabricate a >> set. >>>> Try Norva plastics in Norfolk Virginia. If you send them the good one >> they >>>> may make you two new ones. They've done work for me in KingStarboard >>>> several years ago. >>>> >>>> http://norvaplastics.com/ >>>> >>>> Todd T. >>>> >>>>> On Mon, Oct 18, 2021, 9:24 PM Matt Wilson <mwhornblower at gmail.com> >> wrote: >>>>> >>>>> Hi everyone, >>>>> >>>>> I have a cracked port side rudder check plate and am wondering what is >> the >>>>> best way to repair or replace it? I have a 1990 Rhodes. I am not a >> member >>>>> of the GB parts club. Any help would be appreciated. Hoping to take >> care >>>>> of this in the early off season ;) >>>>> >>>>> Matt Wilson >>>>> Hornblower 2 >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 21 >>>> Date: Mon, 18 Oct 2021 20:48:01 -0500 >>>> From: Matt Wilson <mwhornblower at gmail.com> >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Rudder cheek plate >>>> Message-ID: >>>> <CANbEFCviibdgn9JPFBpMoUinzCNqh3KSYHQkJfZUPuLN9MwmDg at mail.gmail.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Are there different strengths or if I get the same thickness it should >>>> suffice? Thanks Todd! >>>> >>>>> On Mon, Oct 18, 2021 at 8:30 PM Todd Tavares <tavares0947 at gmail.com> >> wrote: >>>>> >>>>> Matt, >>>>> >>>>> I would suggest buying some black UHMWPE and fabricating two new cheek >>>>> plates yourself. >>>>> You could also try to find a plastics production shop to fabricate a >> set. >>>>> Try Norva plastics in Norfolk Virginia. If you send them the good one >> they >>>>> may make you two new ones. They've done work for me in KingStarboard >>>>> several years ago. >>>>> >>>>> http://norvaplastics.com/ >>>>> >>>>> Todd T. >>>>> >>>>>> On Mon, Oct 18, 2021, 9:24 PM Matt Wilson <mwhornblower at gmail.com> >> wrote: >>>>>> >>>>>> Hi everyone, >>>>>> >>>>>> I have a cracked port side rudder check plate and am wondering what is >>>>> the >>>>>> best way to repair or replace it? I have a 1990 Rhodes. I am not a >>>>> member >>>>>> of the GB parts club. Any help would be appreciated. Hoping to take >>>>> care >>>>>> of this in the early off season ;) >>>>>> >>>>>> Matt Wilson >>>>>> Hornblower 2 >>>>>> >>>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 22 >>>> Date: Tue, 19 Oct 2021 00:18:10 -0400 >>>> From: "Michael D. Weisner" <mweisner at ebsmed.com> >>>> To: "'The Rhodes 22 Email List'" <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Rudder cheek plate >>>> Message-ID: <003b01d7c4a0$5405b2b0$fc111810$@ebsmed.com> >>>> Content-Type: text/plain; charset="utf-8" >>>> >>>> Matt, >>>> >>>> If you make a pair, be sure that you specify that you need both sides >> and that they are mirror images with respect to the edge bevels. >>>> >>>> Mike >>>> s/v Wind Lass ('91) >>>> Nissequogue River, NY >>>> >>>> >>>> -----Original Message----- >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of >> Todd Tavares >>>> Sent: Monday, October 18, 2021 9:31 PM >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> >>>> Subject: Re: [Rhodes22-list] Rudder cheek plate >>>> >>>> Matt, >>>> >>>> I would suggest buying some black UHMWPE and fabricating two new cheek >> plates yourself. >>>> You could also try to find a plastics production shop to fabricate a >> set. >>>> Try Norva plastics in Norfolk Virginia. If you send them the good one >> they may make you two new ones. They've done work for me in KingStarboard >> several years ago. >>>> >>>> http://norvaplastics.com/ >>>> >>>> Todd T. >>>> >>>>> On Mon, Oct 18, 2021, 9:24 PM Matt Wilson <mwhornblower at gmail.com> >> wrote: >>>>> >>>>> Hi everyone, >>>>> >>>>> I have a cracked port side rudder check plate and am wondering what is >>>>> the best way to repair or replace it? I have a 1990 Rhodes. I am not >>>>> a member of the GB parts club. Any help would be appreciated. Hoping >>>>> to take care of this in the early off season ;) >>>>> >>>>> Matt Wilson >>>>> Hornblower 2 >>>>> >>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Subject: Digest Footer >>>> >>>> _______________________________________________ >>>> Rhodes22-list mailing list >>>> Rhodes22-list at rhodes22.org >>>> http://rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> >>>> ------------------------------ >>>> >>>> End of Rhodes22-list Digest, Vol 4389, Issue 1 >>>> ********************************************** >>> >> >>
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 