The Rhodes 22 Discussion Group R22 Discussion Group

The Rhodes 22 Discussion Group


< prior

Back to Month

Go to Thread

Member Picture

ROGER PIHLAJA



How to improve Rhodes 22 upwind performance?

2022-03-22; 08:38:42 EDT

Member Since

2002-08-01

Posts: 1438

Mike,

OK, I took a look at the picture you sent and pondered your words.  As you said in your post, in the picture, the genoa is sheeted in too hard and is backwinding the mainsail.  With a 130% genoa, the genoa sheeting car position should be all the way to the front of the track.  It’s a little hard to tell from the picture; but, it looks like you might have the genoa sheeting car a little bit too far back on the track.

My Rhodes 22 has a 150% genoa.  Trying to sail with it furled up to 130% is difficult for me.  At 130%, the proper genoa sheeting car position is actually somewhere in between the forward most position on the cockpit gunnel mounted tracks and the aft most position of the side deck mounted tracks.  These tracks are mounted inboard on the side decks right up against the base of the doghouse.  It’s better for me to furl the genoa a little more, say down to 110-120%, and then just shift to the side deck mounted tracks.  The side deck mounted tracks are a factory option.  Check with Stan.

Another possibility would be a barber hauler setup to get proper genoa sail trim when you don’t have inboard sheeting car positions.  I have no experience with these.  Check the sailing literature.

Do you have a set of genoa telltales with windows mounted 8-12 inches aft of the genoa’s luff?  My genoa has 3 of these windows and they are very helpful for determining proper genoa sail trim.  You want to keep adjusting the genoa sheeting car position until the 3 sets of telltales are all streaming aft and they all break or stop streaming at the same time when you luff up or bear off the wind.  Once you’ve determined that genoa sheeting car position; then, you can quit worrying about it because your rig is giving you all it’s got at that % of the genoa unfurled.  Some people actually mark these genoa sheeting car positions so they can reproduce the settings as they furl and unfurl the genoa.

But, here is what’s confusing me:

At 130%, your boat has a smaller than “normal” genoa.  Most Rhodes 22’s were delivered with a 150% or even a 175% genoa.  So, with a “small” genoa, why does your boat have lee helm?  Is there any chance your IMF mainsail is not fully unfurled?  Does the outhaul pull the foot out nearly to the end of the boom?  If you look inside the slot on the back of the mast, is there any mainsail still rolled up in there?

In the picture, I can’t see enough of the mainsail to make any definitive comments about its state of trim.  The point of maximum draft looks like it might be a little too far aft and too shallow for the light wind conditions.  If true, this sort of mainsail shape will hamper your ability to point upwind and make the “groove” narrower for the helmsman.  The “groove” is the range of “acceptable” wind angles of attack between luffing the sails and stalling the sails.  A narrow “groove” makes the helmsman’s job more difficult because it’s harder to stay within a narrow range vs a broader range.  But, with no battens, backwinding from the genoa, the worn out condition of the sail, and the limited view in the picture, it’s hard to say for sure.  Maybe that’s just the best your IMF mainsail can do.

Does your mainsail have a leech tensioning cord built into it?  Overtightening the leech cord can cause the leech to curl.  You want to tension the leech cord just enough to stop the leech from fluttering and no more.

Other than that, I’m running out of suggestions.

Roger Pihlaja
S/V Dynamic Equilibrium

Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows

See the original archive post
×

Message to Webmaster:

To use your email application to send a messsage to the webmaster rather than this form, .



×

Post to the Rhodes 22 Email List:



×

Sending Post:

Your post is being sent... waiting