< prior
Back to Month
Go to Thread
2022-06-27; 14:37:18 EDT
Member Since
2022-01-25
Posts: 59
Thank s for the tips and the reminder, that could not have been a lot of fun.See the original archive post
> On Jun 27, 2022, at 11:35 AM, Ric Stott <ric at stottarchitecture.com> wrote: > > Hi Rodney > Received our check today for the Delrin Traveler Bar Ends I sent you - many thanks. > Let me know how it works out - I must say - I love mine and use them every time my wife gets on the boat from the beach - I pull the pin and swing the traveller out of the way - or take it off. > If I use the swim ladder, I swing the traveller out of the way first as well. > It also swings out of the way while I’m operating the outboard, which I usually do with the rudder in the up position - whenever I'm backing up to the beach or in the shallows. > Rhodies remember - the Centerboard and Rudder are vulnerable to damage while backing up (intentionally or unintentionally). > Always fully raise the CB while backing up in shallow water, launching or tied up. > Ric > Dadventure > Hampton Bays, NY > PS > Here is a pic of what might happen when you launch with the Center Board control line unsecured which allows the CB to drop. > I successfully retrieved the boat in the fall of 2021, then relaunched to one the boat forward on the trailer, my helper had released the “redline like I asked him to, but he released the CB line instead of the jib fuller line (also red) and I didn’t realize it. As this happened the boat over forward on its own. I was thrilled. > I didn’t notice that the boat had sunk onto its trailer and filled with water to a few inches above the cabin sole until I pulled it back out and noticed water pouring out of the CB trunk. > What a mess.! I ordered a new CB cap from Stan and I made the repairs myself. > > > > Richard F. Stott, AIA, LEED AP > ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> > O -631-283-1777 > C- 516-965-3164 > > > >> On Jun 2, 2022, at 1:13 PM, Rodney Brown <rnelson204 at gmail.com <mailto:rnelson204 at gmail.com>> wrote: >> >> Ric, I’m very interested in your offer. When would be a good time talk >> live? I’d love to pick your brain on the whole set up. >> My cell is (405) 496-5533. >> Thanks again, >> Rodney >> >> On Thu, Jun 2, 2022 at 12:09 Ric Stott <ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com>>> wrote: >> >>> You're welcome to the drawing. The original file, which had additional >>> drawings and instructions was corrupted in the 6 or 7 years since I made >>> the design. I do have an extra set that I had made at the time. I don’t >>> think I”ll need them as the originals are in top shape after 6 years of use >>> - I would sell them for $100. >>> I’ll take a couple of photos later today or tomorrow and get those to you >>> as well. >>> Ric >>> Dadventure >>> Richard F. Stott, AIA, LEED AP >>> ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> >>> O -631-283-1777 >>> C- 516-965-3164 >>> >>> >>> >>>> On Jun 2, 2022, at 1:03 PM, Rodney Brown <rnelson204 at gmail.com <mailto:rnelson204 at gmail.com>> wrote: >>>> >>>> Ric thx for the diagram, it came through. Do you have a picture of the >>> the machines but installed on the boat. Im a super visual learner, drives >>> my wife crazy. >>>> Thanks for sharing your work 👍 >>>> >>>> Sent from my iPhone >>>> >>>>> On Jun 2, 2022, at 11:26, Ric Stott <ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com>> <mailto: >>> ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com>>>> wrote: >>>>> >>>>> Rodney >>>>> I found a drawing, but its not the drawing I was hoping to locate. I’ll >>> try to attach it here. IF it gets scrubbed, I’ll resend through my gmail >>> account. >>>>> Please let me know if the attachment makes it. >>>>> Once the two pieces were fabricated, I installed them onto the >>> split-backstay, then drilled a 1/4” hole through the assembly and used a >>> 1/4” ‘Fast-Pin’ t keep it in place. Its really easy to pull the fast-pin >>> and swing one side out of the way of the motor, or the stern ladder on the >>> other side. This makes it really convenient for boarding folks from astern >>> (the ladder) or working on the motor. >>>>> Best >>>>> Ric >>>>> Dadventure >>>>> >>>>> Richard F. Stott, AIA, LEED AP >>>>> ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com>> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com> <mailto:ric at stottarchitecture.com <mailto:ric at stottarchitecture.com>>> >>>>> O -631-283-1777 >>>>> C- 516-965-3164 >>>>> >>>>> >>>>> >>>>>> On Jun 2, 2022, at 10:09 AM, Rodney Brown <rnelson204 at gmail.com <mailto:rnelson204 at gmail.com> <mailto:rnelson204 at gmail.com <mailto:rnelson204 at gmail.com>> >>> <mailto:rnelson204 at gmail.com <mailto:rnelson204 at gmail.com> <mailto:rnelson204 at gmail.com <mailto:rnelson204 at gmail.com>>>> wrote: >>>>>> >>>>>> Ric, I’d love to see the drawings and pic of the set up installed if >>> you have time. >>>>>> Thanks >>>>>> Rodney >>>>>> >>>>>> Sent from my iPhone >>>>>> >>>>>>>> On Jun 2, 2022, at 06:32, Ric Stott <ric at stottarchitecture.com> >>> wrote: >>>>>>> >>>>>>> My traveler conversion does not move easily and the line tension >>> makes a big difference. Try easing the tension on the cam-cleat. This will >>> make movement easier but it will never be fast and never be the tool you >>> use to de-power quickly, the main sheet is best for that. What I like best >>> about Stan’s invention is the ability to pull the pins from the ends and >>> swing the traveler out of the way or take it off completely in seconds. I >>> designed the ends and had them fabricated out of Delrin at a local machine >>> shop. If anyone is interested I can probably dig out the drawing. >>>>>>> Ric >>>>>>> Dadventure. >>>>>>> >>>>>>> Sent from my iPhone >>>>>>> >>>>>>>> On Jun 1, 2022, at 9:27 PM, Melvyn Rothbard via Rhodes22-list < >>> rhodes22-list at rhodes22.org> wrote: >>>>>>>> >>>>>>>> I had the same issue as Peter. Once I loosened the lines a little >>> it worked much better >>>>>>>> Mel Rothbard >>>>>>>> >>>>>>>> Sent from Yahoo Mail on Android >>>>>>>> >>>>>>>> On Wed, Jun 1, 2022 at 9:18 PM, Peter Nyberg<peter at sunnybeeches.com> >>> wrote: Joe, >>>>>>>> >>>>>>>> I know on mine that if there's too much tension on the line, working >>> the traveller to port or starboard is more difficult. Other than that, I >>> can only suggest cleaning the line, and making sure that all the little >>> blocks turn freely. >>>>>>>> >>>>>>>> --Peter >>>>>>>> >>>>>>>>>> On 2022-06-01, at 20:51:14 EDT, jpd9668 wrote: >>>>>>>>> >>>>>>>>> Do those of you Rhodie's who have converted to the new traveller >>> have any >>>>>>>>> problems with it sticking? Mine has become very difficult to >>> operate. Any >>>>>>>>> maintenance suggestions?Joe DempseySV RespiteDeltaville, VASent via >>> the Samsung >>>>>>>>> Galaxy S22 5G, an AT&T 5G smartphone >>>>>>>>> >>>>>>>> >>>>>>>> >>>>> >>>>> -------------- next part -------------- >>>>> A non-text attachment was scrubbed... >>>>> Name: Traveler End Drawing2.pdf >>>>> Type: application/pdf >>>>> Size: 85813 bytes >>>>> Desc: not available >>>>> URL: < >>> http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf> >>> < >>> http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf> <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220602/4ada2a03/attachment.pdf>> > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: IMG_2665.jpeg > Type: image/jpeg > Size: 2801232 bytes > Desc: not available > URL: <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220627/6e2b9f29/attachment.jpeg <http://rhodes22.org/pipermail/rhodes22-list/attachments/20220627/6e2b9f29/attachment.jpeg>>
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 