< prior
Back to Month
Go to Thread
2023-10-26; 17:25:11 EDT
Member Since
2008-12-25
Posts: 1035
The worst experience was 150 yd out from a breakwall protecting the marina entrance I was headed toward in 20 Kt wind. When my windward upper shroud chainplate let go, I KISS anchored because I was also out of gas.. I managed to call for a tow anchored only 25 yd from the rocks. Regards, Rick LangeSee the original archive post
On Thu, Oct 26, 2023 at 4:34 PM ROGER PIHLAJA <roger_pihlaja at msn.com> wrote: > OK Rick, > > I’ve given the reasons why it’s desirable to anchor using a carabiner and > the bow eye. These are based upon sound physics and they will improve the > anchor holding or shrink the swing radius EVERY SINGLE TIME! If you want > to reject it because you might trip and fall overboard, that’s your > prerogative. How often do you have to set the anchor in heavy weather? > Don’t you think these are the very conditions wherein better anchor holding > is highly desirable? Good luck > > Roger Pihlaja > S/V Dynamic Equilibrium > Sent from my iPhone > > > On Oct 26, 2023, at 4:08 PM, Rick Lange <sloopblueheron at gmail.com> > wrote: > > > > Roger, > > > > The boat hook and carabiner are unnecessary complications. And > > complications threaten safety. > > > > Regards, > > > > Rick Lange > > > > > >> On Thu, Oct 26, 2023 at 3:14 PM ROGER PIHLAJA <roger_pihlaja at msn.com> > wrote: > >> > >> Rick, > >> > >> Assuming you have a boat hook on board, you only need to thread the > anchor > >> rode thru the carabiner once. After that, you use the boat hook to > handle > >> the anchor rode. It’s no worse than any other time you need to be on > the > >> bow handling the anchor. > >> > >> Roger Pihlaja > >> S/V Dynamic Equilibrium > >> > >> Sent from my iPhone > >> > >>> On Oct 26, 2023, at 2:36 PM, Rick Lange <sloopblueheron at gmail.com> > >> wrote: > >>> > >>> Hi Roger, > >>> > >>> The problem with running or tying the anchor rode to the bow eye is > that > >>> you can't safely sit in the bow pulpit and do that during heavy > weather. > >>> The best thing is to first run the rode through a bow chock, tie the > rode > >>> to the bow cleat, then drop the anchor from the bow rail. You can do > all > >>> that sitting securely in the pulpit with your legs hanging over the > edge > >> of > >>> the deck. > >>> > >>> Regards, > >>> > >>> Rick Lange > >>> > >>> > >>>> On Thu, Oct 26, 2023 at 12:26 PM ROGER PIHLAJA <roger_pihlaja at msn.com > > > >>>> wrote: > >>>> > >>>> Although I can't open the attachment, my R-22 has the same single bow > >>>> cleat you describe on your boat. There are many factors that affect > >> how a > >>>> boat lies to its anchor. Factors which have a much larger effect on > the > >>>> boat than the slight off-center position of the anchor rode include > wind > >>>> and current direction and strength, distribution and amount of > windage ( > >>>> i.e. Do you have your pop top enclosure &/or boom room up? ), and > >>>> underwater configuration ( i.e. Do you have the centerboard &/or > rudder > >> up > >>>> or down? ). There should be a pair of line chocks mounted port and > >>>> starboard on the toe rails up on the bow. On my boat, these line > chocks > >>>> are mounted on top of the toe rail about halfway in-between the > >> stanchions > >>>> on the bow pulpit. You should run the anchor rode from the cleat thru > >> one > >>>> or the other of these line chocks. Routing the anchor rode thru these > >> line > >>>> chocks will not only bring the effective point of attachment closer to > >> the > >>>> boat's centerline on the bow, it will also help to eliminate chafing > on > >> the > >>>> anchor rode and the boat. If your boat doesn't have these bow line > >> chocks; > >>>> then you should add them ASAP. they also help eliminate chafe from > dock > >>>> lines. > >>>> > >>>> One thing you should also consider doing is routing the anchor rode > >> thru a > >>>> locking rock-climbing carabineer. Then, attach the carabineer to the > >>>> trailering bow eye and run the anchor rode thru one of the bow line > >> chocks, > >>>> and the bow cleat. Now, the effective anchor rode attachment point is > >>>> about 2 ft closer to the water. This does good things for your anchor > >>>> scope ratio. An example will serve to illustrate my point: > >>>> > >>>> Suppose you want to anchor in 10 ft of water depth. If you route your > >>>> anchor rode thru the bow chock, which is about 3 ft above the water, > you > >>>> have to add 10 + 3 = 13 ft. To achieve a 7:1 scope ratio you would > >> have to > >>>> let out 13 X 7 = 91 ft of anchor rode. If you route your anchor rode > >> thru > >>>> the bow eye with a carabineer, you will have reduced the attachment > >> point's > >>>> height above the water to about 1 ft and 10 + 1 = 11 ft. Now, to > >> achieve > >>>> the same 7:1 scope ratio, you only have to let out 11 X 7 = 77 ft of > >> anchor > >>>> rode. This is a significant reduction in your swing radius. In a > >> crowded > >>>> anchorage, this is a useful trick, with no reduction in safety. Or, > you > >>>> can let out the original 91 ft of anchor rode and achieve 91 / 11 = > 8.27 > >>>> scope ratio. With the same 91 ft swing radius, this larger scope > ratio > >>>> makes your anchor less likely to drag. > >>>> > >>>> This is SOP anchoring technique aboard S/V Dynamic Equilibrium. > >>>> > >>>> Roger Pihlaja > >>>> S/V Dynamic Equilibrium > >>>> > >>>> ________________________________ > >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > >>>> Mitch Mitchell <mitchpadl at gmail.com> > >>>> Sent: Thursday, October 26, 2023 10:37 AM > >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > >>>> Subject: [Rhodes22-list] Anchoring > >>>> > >>>> A non-text attachment was scrubbed... > >>>> Name: Anchor.heic > >>>> Type: image/heic > >>>> Size: 22840 bytes > >>>> Desc: not available > >>>> URL: < > >>>> > >> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20231026/8ba83f88/attachment.bin > >>>> < > >>>> > >> > http://rhodes22.org/pipermail/rhodes22-list/attachments/20231026/8ba83f88/attachment.bin > >>>>>> > >>>> -------------- next part -------------- > >>>> Hoping to get some suggestions for anchoring. My boat just has a > single > >>>> cleat centered on the bow and I’m trying to figure out the best way to > >> run > >>>> the anchor line. Should I go between the two center pulpit stanchions? > >> If I > >>>> do that it would be rubbing against the forestay which doesn’t seem > >> good. > >>>> Should I run it around the second set of pulpit stanchions? That puts > >> the > >>>> pull to the side which would make the boat go from side to side. I’ve > >> read > >>>> where other people have added all kinds of anchor rollers, chocks etc. > >> but > >>>> I am not interested in doing that. Thanks! I’ve included an image of > the > >>>> bow. > >>>> > >> >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 