< prior
Back to Month
Go to Thread
2024-04-03; 08:48:51 EDT
Member Since
2002-08-01
Posts: 1438
Hi Patrick, I would check the oil level 1st. On a 2 cylinder engine, I would pull both spark plugs when checking the compression. That way, the starter will spin the engine faster and both cylinders will see the same test RPM. Roger Pihlaja S/V Dynamic Equilibrium 1978 Sanford, MISee the original archive post
________________________________ From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of PBR <pbryanriley at gmail.com> Sent: Wednesday, April 3, 2024 8:36 AM To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> Subject: Re: [Rhodes22-list] Honda BF9.9 Oil from carb Thanks Roger, I will try all of these suggestions. I'll keep you all posted but it might take me a while to find the time. I do use just ethanol free gas and my modus operandi has been to run the gas out, but I admit during this time when I have been just starting and running the motor periodically I probably have skipped that a few times. I have a compression tester with the rubber insert. Came with a tune up kit I picked up about 35 years ago so probably american made and still working... To do this I am guessing I would hook up the battery and crank the motor while holding the tester in place? both plugs out or one in one out. (I seem to remember with 8 cyl engines my pals just did one at a time and started the engine). I do have an alternate motor ready to go on a Rhodes so if I get some sailing opportunities I have no excuses not to get out there. Patrick On Tue, Apr 2, 2024 at 11:24 PM ROGER PIHLAJA <roger_pihlaja at msn.com> wrote: > Hi Patrick, > > I’ve been thinking more about your issue with engine oil dripping out the > carburetor. Check the engine oil level with the dip stick. If the oil > level is high; then, you may have an issue with the float level in the > carburetor. High fuel level in the float bowl would allow fuel to > contaminate the engine oil. Eventually, the diluted engine oil level would > get high enough that oil would start backing up into the carburetor, > resulting in your observed carb oil drip. A sticky float would be > consistent with an engine that sits a lot between runs. I always > disconnect the fuel line and run the engine until the carburetor runs dry. > I think this explanation is more likely than stuck or worn piston rings. > > Roger Pihlaja > S/V Dynamic Equilibrium > 1978 Sanford, MI > Sent from my iPhone > > > On Apr 2, 2024, at 4:02 PM, ROGER PIHLAJA <Roger_Pihlaja at msn.com> wrote: > > > > Hi Patrick, > > > > I have a Honda BF9.9AXSA outboard motor, model year 2000. I use it on > my Walker Bay RIB. If you have a compression tester, you can quickly > determine the status of your piston rings and valves. The factory > compression spec is 156 +/- 14 psi when the engine is cold. If your > compression meets spec in both cylinders; then, your piston rings and > valves are OK. If the compression values are low; then, squirt some engine > oil into the spark plug hole on each cylinder and retest the compression. > If the compression improves; then, you have worn/stuck piston rings. If > the compression does not improve; then, you have valve leakage issues. > The only way to fix valve leakage is with a cylinder head rebuild. > However, since your engine still runs, if your problem is stuck piston > rings; then, you may be able to free them up. Drain out about ½ the > crankcase oil and refill with a product like Slick 50 Synthetic Oil > Treatment. Squirt some Slick 50 into each spark plug hole, gently crank it > over a few revs, and then let it sit overnight. The next day, start the > engine, and let it run at idle for 15-20 minutes. Then, shut it down and > change the oil. Hopefully, this will free up the piston rings. I don't > have much faith in any fuel additive's ability to free up stuck piston > rings. > > > > My M/Y 2000 engine has a crankcase vent that dumps directly to the > atmosphere via a rubber hose on the port side. The crankcase breather > cover sits just in front of the timing belt sprocket on the top of the > engine. I've never had my breather cover off because I've never needed to > get in there. However, given that it vents to the atmosphere, I doubt > there is any sort of PCV valve that might get stuck or clogged. However, I > suppose it's possible the vent port itself &/or the hose might be clogged. > So, it might be worth a look underneath the breather cover just to verify > that the plumbing is free and clear. > > > > Try these suggestions and let's see what happens. Good Luck! > > > > Roger Pihlaja > > S/V Dynamic Equilibrium > > 1978 Sanford, MI > > > > > > > > ________________________________ > > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Michael D. Weisner <mweisner at ebsmed.com> > > Sent: Tuesday, April 2, 2024 2:12 PM > > To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org> > > Subject: Re: [Rhodes22-list] Honda BF9.9 Oil from carb > > > > Patrick, > > > > I think that if you have a problem with "stuck" piston rings, you would > know it. I would suspect that there would be a loud noise and the engine > probably would not run at low speeds as it seized up. > > > > My guess is more a problem with the crankcase ventilation system. > Usually there is a PCV style one-way valve that sucks oil fumes out of the > crankcase, burning them by introducing into the air intake. Check the air > filter which is usually part of the recirculation circuit as it can become > saturated with oil. > > > > Is the engine consuming oil? Have you checked the oil level using the > dipstick? The smoke and excess oil can be the result of worn (not stuck) > piston rings or valves that are allowing the oil to pass into the > combustion path. > > > > Mike > > s/v Wind Lass ('91) > > Nissequogue River, NY > > I’d rather be sailing :~) > > > > -----Original Message----- > > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On Behalf Of > PBR > > Sent: Tuesday, April 2, 2024 1:52 PM > > To: rhodes22-list at rhodes22.org > > Subject: [Rhodes22-list] Honda BF9.9 Oil from carb > > > > Hello all. > > > > I have a Honda 9.9 2 cyl. that has been mostly sitting for a few years. > > It sat on the boat in Kitty Hawk (humid environment) for one winter > untouched (2018). Since then I have not used it on the water but always > expecting that I might anytime soon I did not winterize but dutifully > started it every couple of months throughout the winters and ran it a bit > with the water hose. Always started easy and ran good. Some smoke at > first but not enough to concern me. This time as I was about to put the > thing in to use I put a bucket (trash can ) around it and ran it again. > > Started easy , runs good, again some smoking, enough to get me curious > but not constant at all speeds. > > > > Looking under the cowling I see oil dripping from the carb intake (clean > golden oil). Still running fine.I am hoping there may be a *vent clog* or > something rather than just frozen rings. Any thoughts? *Stuck valve?* ( > but runs pretty good) > > > > This 1999 motor has VERY VERY low miles and looks brand new so I hate to > scrap it but given the date of manufacture the value is probably less than > a marine repair will charge me to take a look. Hoping for a miracle > solution. Twice I have removed mud dauber bee nests from under the cowling > so maybe I can find something suspicous. > > > > The trash can I ran it in did have some residual oil clinging to the > sides but I don't know how much might be normal. > > > > My plan next trip in a couple of weeks is to look for clogs and try > running again maybe with a high dose of sea foam or something. Not sure of > any miracle sauce that might help stuck rings. > > > > Patrick > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 