< prior
Back to Month
Go to Thread
2024-06-29; 18:01:52 EDT
Member Since
2024-06-18
Posts: 58
I just got a bf100 for my boat! Glad to see that somebody else has a similar engine. Being 4 stroke (and not prone to seizing while idle) plus the 60w rectifier sold me!See the original archive post
On Sat, Jun 29, 2024 at 5:14 PM PBR <pbryanriley at gmail.com> wrote: > Roger, > Success. It seems it was a stuck float that started me down this path. > Did not find anything clogging it but cleaning it up appeared to fix > things. Got it running and the smoking quickly cleared up too. Now the > only issue is after working perfectly last trip when I was compression > testing, this time the electric start is dead. Appears to be a stuck relay > which is a part not available anywhere. Starts easy enough by pulling > the rope for now. I'll check with a honda stealer for that part I guess. > Thanks for your wise advice. > Patrick > > > On Wed, Jun 12, 2024 at 11:29 AM ROGER PIHLAJA <roger_pihlaja at msn.com> > wrote: > > > Patrick, > > > > I’m sorry, I tend to skip obvious steps. Yes, you have to remove the > > throttle linkage and carb to get to the float bowl. > > > > Roger Pihlaja > > S/V Dynamic Equilibrium > > 1978. Sanford, MI > > Sent from my iPhone > > > > > On Jun 12, 2024, at 11:04 AM, PBR <pbryanriley at gmail.com> wrote: > > > > > > Thanks Roger, > > > Can't access the float bowl screws without removing the carb but.It > looks > > > like only two bolts to pull the carb off. So i will attempt to clean > > up > > > and unstick the needle next time I get back to boats in a couple of > > weeks. > > > Patrick > > > > > > > > >> On Thu, Jun 6, 2024 at 6:53 PM ROGER PIHLAJA <roger_pihlaja at msn.com> > > wrote: > > >> > > >> Patrick, > > >> > > >> Assuming the problem is a sticky needle &/or float, you can clean it > out > > >> with minimal disassembly: > > >> > > >> Remove the float bowl and fuel line from the carburetor. Gently move > > the > > >> float. It should move several mm with little resistance. > > >> > > >> Spray carb cleaner into the fuel line inlet. You should see carb > > cleaner > > >> dripping out of the needle valve. > > >> > > >> Remove the float and needle valve. Be careful not to lose the needle > > >> valve seat seal. Inspect the male part of the needle valve. Clean > off > > any > > >> residual deposits with carb cleaner. Spray carb cleaner up into the > > needle > > >> valve seat passage. You should see carb cleaner dripping out of the > > fuel > > >> line inlet. > > >> > > >> Reassemble the carb and reconnect the fuel line. > > >> > > >> Since you suspect the oil is fuel diluted, I recommend changing the > oil. > > >> > > >> A compression test of 110 psi isn’t great. But, the engine should > still > > >> run. > > >> > > >> Roger Pihlaja > > >> S/V Dynamic Equilibrium > > >> 1978. Sanford, MI > > >> > > >> Sent from my iPhone > > >> > > >>>> On Jun 6, 2024, at 1:06 PM, PBR <pbryanriley at gmail.com> wrote: > > >>> > > >>> Roger, et. al., > > >>> > > >>> Finally had a chance to troubleshoot this issue that began as oil > > >> dripping > > >>> from carb intake and smoking some. > > >>> I can't find any sign of a breather that might be clogged, everything > > >> under > > >>> the hood is pristine clean. > > >>> > > >>> Oil was definitely overfilled. I drained out about a pint and it > still > > >>> shows nearly full. Golden color difficult to see but by rolling the > > >>> dipstick on a paper towel you could see the top level. What I > drained > > >> out > > >>> also seems to have a viscosity lower than I would expect of pure oil > > and > > >> my > > >>> wife said it smelled of gas. So, stuck float is or was a most likely > > >>> culprit. > > >>> > > >>> I checked compression and got 110 psi on both cylinders. squirted in > > some > > >>> oil but could not get it to change. Seems low but could be my 40 > year > > >> old > > >>> tester and me trying to get a good push seal. So, my rings are > > probably > > >>> not an issue. > > >>> > > >>> So, what next with a sticky float.? I don't want to take the carb > apart > > >>> with my skill level and lack of a clean shop to work in. It may be > > fixed > > >>> already and I was just seeing the after effect of overfilled oil. I > > have > > >>> the motor on a dolly so I can tip it on it side, tap on stuff etc.. > I > > >>> might just try to see if it runs OK before putting in clean oil in > case > > >> it > > >>> is still stuck. > > >>> > > >>> Patrick > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> > > >>>> On Wed, Apr 3, 2024 at 8:48 AM ROGER PIHLAJA <roger_pihlaja at msn.com > > > > >> wrote: > > >>>> > > >>>> Hi Patrick, > > >>>> > > >>>> I would check the oil level 1st. On a 2 cylinder engine, I would > pull > > >>>> both spark plugs when checking the compression. That way, the > starter > > >> will > > >>>> spin the engine faster and both cylinders will see the same test > RPM. > > >>>> > > >>>> Roger Pihlaja > > >>>> S/V Dynamic Equilibrium > > >>>> 1978 Sanford, MI > > >>>> ________________________________ > > >>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf > of > > >> PBR > > >>>> <pbryanriley at gmail.com> > > >>>> Sent: Wednesday, April 3, 2024 8:36 AM > > >>>> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > >>>> Subject: Re: [Rhodes22-list] Honda BF9.9 Oil from carb > > >>>> > > >>>> Thanks Roger, > > >>>> I will try all of these suggestions. I'll keep you all posted but > it > > >> might > > >>>> take me a while to find the time. I do use just ethanol free gas > and > > my > > >>>> modus operandi has been to run the gas out, but I admit during this > > time > > >>>> when I have been just starting and running the motor periodically I > > >>>> probably have skipped that a few times. I have a compression tester > > >> with > > >>>> the rubber insert. Came with a tune up kit I picked up about 35 > > years > > >> ago > > >>>> so probably american made and still working... To do this I am > > >> guessing I > > >>>> would hook up the battery and crank the motor while holding the > tester > > >> in > > >>>> place? both plugs out or one in one out. (I seem to remember with 8 > > cyl > > >>>> engines my pals just did one at a time and started the engine). > > >>>> > > >>>> I do have an alternate motor ready to go on a Rhodes so if I get > some > > >>>> sailing opportunities I have no excuses not to get out there. > > >>>> > > >>>> Patrick > > >>>> > > >>>> > > >>>> On Tue, Apr 2, 2024 at 11:24 PM ROGER PIHLAJA < > roger_pihlaja at msn.com> > > >>>> wrote: > > >>>> > > >>>>> Hi Patrick, > > >>>>> > > >>>>> I’ve been thinking more about your issue with engine oil dripping > out > > >> the > > >>>>> carburetor. Check the engine oil level with the dip stick. If the > > oil > > >>>>> level is high; then, you may have an issue with the float level in > > the > > >>>>> carburetor. High fuel level in the float bowl would allow fuel to > > >>>>> contaminate the engine oil. Eventually, the diluted engine oil > level > > >>>> would > > >>>>> get high enough that oil would start backing up into the > carburetor, > > >>>>> resulting in your observed carb oil drip. A sticky float would be > > >>>>> consistent with an engine that sits a lot between runs. I always > > >>>>> disconnect the fuel line and run the engine until the carburetor > runs > > >>>> dry. > > >>>>> I think this explanation is more likely than stuck or worn piston > > >> rings. > > >>>>> > > >>>>> Roger Pihlaja > > >>>>> S/V Dynamic Equilibrium > > >>>>> 1978 Sanford, MI > > >>>>> Sent from my iPhone > > >>>>> > > >>>>>> On Apr 2, 2024, at 4:02 PM, ROGER PIHLAJA <Roger_Pihlaja at msn.com> > > >>>> wrote: > > >>>>>> > > >>>>>> Hi Patrick, > > >>>>>> > > >>>>>> I have a Honda BF9.9AXSA outboard motor, model year 2000. I use > it > > on > > >>>>> my Walker Bay RIB. If you have a compression tester, you can > quickly > > >>>>> determine the status of your piston rings and valves. The factory > > >>>>> compression spec is 156 +/- 14 psi when the engine is cold. If > your > > >>>>> compression meets spec in both cylinders; then, your piston rings > and > > >>>>> valves are OK. If the compression values are low; then, squirt > some > > >>>> engine > > >>>>> oil into the spark plug hole on each cylinder and retest the > > >> compression. > > >>>>> If the compression improves; then, you have worn/stuck piston > rings. > > >> If > > >>>>> the compression does not improve; then, you have valve leakage > > issues. > > >>>>> The only way to fix valve leakage is with a cylinder head rebuild. > > >>>>> However, since your engine still runs, if your problem is stuck > > piston > > >>>>> rings; then, you may be able to free them up. Drain out about ½ > the > > >>>>> crankcase oil and refill with a product like Slick 50 Synthetic Oil > > >>>>> Treatment. Squirt some Slick 50 into each spark plug hole, gently > > >> crank > > >>>> it > > >>>>> over a few revs, and then let it sit overnight. The next day, > start > > >> the > > >>>>> engine, and let it run at idle for 15-20 minutes. Then, shut it > down > > >> and > > >>>>> change the oil. Hopefully, this will free up the piston rings. I > > >> don't > > >>>>> have much faith in any fuel additive's ability to free up stuck > > piston > > >>>>> rings. > > >>>>>> > > >>>>>> My M/Y 2000 engine has a crankcase vent that dumps directly to the > > >>>>> atmosphere via a rubber hose on the port side. The crankcase > > breather > > >>>>> cover sits just in front of the timing belt sprocket on the top of > > the > > >>>>> engine. I've never had my breather cover off because I've never > > needed > > >>>> to > > >>>>> get in there. However, given that it vents to the atmosphere, I > > doubt > > >>>>> there is any sort of PCV valve that might get stuck or clogged. > > >>>> However, I > > >>>>> suppose it's possible the vent port itself &/or the hose might be > > >>>> clogged. > > >>>>> So, it might be worth a look underneath the breather cover just to > > >> verify > > >>>>> that the plumbing is free and clear. > > >>>>>> > > >>>>>> Try these suggestions and let's see what happens. Good Luck! > > >>>>>> > > >>>>>> Roger Pihlaja > > >>>>>> S/V Dynamic Equilibrium > > >>>>>> 1978 Sanford, MI > > >>>>>> > > >>>>>> > > >>>>>> > > >>>>>> ________________________________ > > >>>>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on > behalf > > of > > >>>>> Michael D. Weisner <mweisner at ebsmed.com> > > >>>>>> Sent: Tuesday, April 2, 2024 2:12 PM > > >>>>>> To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org> > > >>>>>> Subject: Re: [Rhodes22-list] Honda BF9.9 Oil from carb > > >>>>>> > > >>>>>> Patrick, > > >>>>>> > > >>>>>> I think that if you have a problem with "stuck" piston rings, you > > >> would > > >>>>> know it. I would suspect that there would be a loud noise and the > > >> engine > > >>>>> probably would not run at low speeds as it seized up. > > >>>>>> > > >>>>>> My guess is more a problem with the crankcase ventilation system. > > >>>>> Usually there is a PCV style one-way valve that sucks oil fumes out > > of > > >>>> the > > >>>>> crankcase, burning them by introducing into the air intake. Check > the > > >> air > > >>>>> filter which is usually part of the recirculation circuit as it can > > >>>> become > > >>>>> saturated with oil. > > >>>>>> > > >>>>>> Is the engine consuming oil? Have you checked the oil level using > > the > > >>>>> dipstick? The smoke and excess oil can be the result of worn (not > > >> stuck) > > >>>>> piston rings or valves that are allowing the oil to pass into the > > >>>>> combustion path. > > >>>>>> > > >>>>>> Mike > > >>>>>> s/v Wind Lass ('91) > > >>>>>> Nissequogue River, NY > > >>>>>> I’d rather be sailing :~) > > >>>>>> > > >>>>>> -----Original Message----- > > >>>>>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> On > Behalf > > Of > > >>>>> PBR > > >>>>>> Sent: Tuesday, April 2, 2024 1:52 PM > > >>>>>> To: rhodes22-list at rhodes22.org > > >>>>>> Subject: [Rhodes22-list] Honda BF9.9 Oil from carb > > >>>>>> > > >>>>>> Hello all. > > >>>>>> > > >>>>>> I have a Honda 9.9 2 cyl. that has been mostly sitting for a few > > >>>> years. > > >>>>>> It sat on the boat in Kitty Hawk (humid environment) for one > winter > > >>>>> untouched (2018). Since then I have not used it on the water but > > >> always > > >>>>> expecting that I might anytime soon I did not winterize but > dutifully > > >>>>> started it every couple of months throughout the winters and ran > it a > > >> bit > > >>>>> with the water hose. Always started easy and ran good. Some smoke > > at > > >>>>> first but not enough to concern me. This time as I was about to > put > > >> the > > >>>>> thing in to use I put a bucket (trash can ) around it and ran it > > again. > > >>>>>> Started easy , runs good, again some smoking, enough to get me > > curious > > >>>>> but not constant at all speeds. > > >>>>>> > > >>>>>> Looking under the cowling I see oil dripping from the carb intake > > >>>> (clean > > >>>>> golden oil). Still running fine.I am hoping there may be a *vent > > clog* > > >>>> or > > >>>>> something rather than just frozen rings. Any thoughts? *Stuck > > >> valve?* ( > > >>>>> but runs pretty good) > > >>>>>> > > >>>>>> This 1999 motor has VERY VERY low miles and looks brand new so I > > hate > > >>>> to > > >>>>> scrap it but given the date of manufacture the value is probably > less > > >>>> than > > >>>>> a marine repair will charge me to take a look. Hoping for a > miracle > > >>>>> solution. Twice I have removed mud dauber bee nests from under the > > >>>> cowling > > >>>>> so maybe I can find something suspicous. > > >>>>>> > > >>>>>> The trash can I ran it in did have some residual oil clinging to > the > > >>>>> sides but I don't know how much might be normal. > > >>>>>> > > >>>>>> My plan next trip in a couple of weeks is to look for clogs and > try > > >>>>> running again maybe with a high dose of sea foam or something. Not > > >> sure > > >>>> of > > >>>>> any miracle sauce that might help stuck rings. > > >>>>>> > > >>>>>> Patrick > > >>>>>> > > >>>>> > > >>>> > > >> > > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 