< prior
Back to Month
Go to Thread
2014-03-07; 09:34:03 EST
Member Since
2003-09-15
Posts: 1076
a lot of misinformation here but am too busy to infringe on your fun - just want to remind all that no one is talking about the combination Keel/Diamondboard boats and that you old timers can get the same pivoting benefits effect by simply sailing with your prior style board being kept raked slightly aft. . . . . or you can buy a fixed keel boat and bite your tongue. ssSee the original archive post
On 3/7/14, 8:51 AM, Ric Stott wrote: > Hmm! > I'm very grateful for this thread and this communication. > I see this as an inherent and dangerous weakness in the boat. > I was sailing in a keel boat once long ago. We were on our way to a > race in Fisher's Island sound. > It was foggy and before GPS, we proudly knew where we were, but not > to the nearest yard. > There are some tall rocks close to the edge of the channel in > otherwise very deep water. > There was a 2 ft chop on a 2 foot swell from offshore and it was > low tide. > The wind had dropped off and we were moving only a knot or two, > bobbing in the bumps. > Cocky and content, alert and on watch, we were cruising along with the > chute up. > Suddenly, the boat dropped off a wave on the keel came down on a rock. > We hit so hard I bit my tung bloody from the impact. The mast and > rigging twanged like it broke. We quickly checked the bilge fearing > the worse, but to everyones surprise - no leaks. > An underwater inspection revealed a big dent on the bottom of the lead > keel. > If that happened in a Rhodes 22, it would have driven the CB right > through the cap and flooded the boat. > No wonder Stan builds in floatation. > > There must be a solution here. > What holds the garden hose in place, anybody know? > > Ric > Dadventure > > > On Mar 6, 2014, at 9:58 PM, cjlowe at sssnet.com wrote: > >> I have a different take on some of these issues, don't know if I'm >> right, >> probably just a different take. I think I remember someone on the list >> saying the pcv pieces slide on each side of the cb pin and act as a >> sacrificial bushing , so the stainless steel pivot pin doesn't eat >> out the >> fiberglass in the side and bottom of the grove. Hope I didn't dream >> that, >> because I spent a lot of time making them bushings, mine didn't have >> them. >> I'm not sure trying to limit the cb's vertical movement is the best >> idea. I'm thinking anything you put in the channels has a chance of >> falling out and jambing the cb travel. Anything hard screwed in the >> channels has a good chance of tearing big holes in the cb trunk and >> taking out both sides of the cb cap. If you think fixing the cb cap >> was >> a pain, ask Lou how much fun it is to do repairs inside the >> centerboard >> trunk. >> I'm thinking the best bet is to not anchor/moor in shallow water, >> don't >> motor backward in shallow water, and NEVER EVER splash the boat unless >> the cb pendant is cleated with the cb in the UP position. Any other >> ides >> on this are more than welcome. >> >> Jerry >> >> >> >>> I have changed the title of this exchange as it appear the topic has >>> morphed >>> from the matter of the mast post base to the question of how the >>> centreboard >>> is attached and how this might result in damage to the cap if the >>> centreboard is not held in the up position when launching. >>> >>> My centreboard pivot pin rides in two vertical channels in the >>> housing >>> that >>> are about 5" long. Those grooves are very clear in the second photo >>> that >>> Rob >>> Lowe just posted. As I saw it, the channels would allow the pin to be >>> dropped down to the proper position without the need to insert the >>> pin >>> from >>> the outside of the housing. It now occurs to me that this design >>> might >>> also have been intended to allow the pivot pin to rise up inside the >>> housing >>> should the centreboard hit something. Makes sense although perhaps >>> not if >>> this would allow the centreboard to damage the cap. >>> >>> In my case two length of .5 inch rigid PVC pipe were placed in each >>> channel >>> above the pin. It appears that these pipes were intended to prevent >>> the >>> pin >>> from rising up. As I mentioned earlier, I was pretty sure that the >>> cap had >>> never been removed and assumed, therefore, that the pieces of pipe >>> were >>> part >>> of the original design. Now I am beginning to wonder if this was >>> some kind >>> of retrofit by a previous owner who, perhaps, was responding to >>> damage >>> caused when the centreboard was pushed into the cap. >>> >>> I am inclined to leave the pieces of pipe out when I reinstall the >>> centreboard or perhaps search for something that might act as a shock >>> absorber but still allow the board to raise up if it hits a solid >>> object. >>> Perhaps shorter lengths of flexible plastic tubing would work. >>> >>> Has anyone else found a similar arrangement in the pivot pin channel? >>> Any thoughts? >>> >>> Graham >>> >>> >>> -----Original Message----- >>> From: rhodes22-list-bounces at rhodes22.org >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Lowe, Rob >>> Sent: March-06-14 3:13 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] Searching the archives and settled >>> step >now >>> mast step cb leak >>> >>> It seems like there are various versions of CB and the lift >>> systems. Here >>> are some photos that someone (I forgot who, sorry!) posted of their >>> CB >>> taken >>> apart. - rob >>> >>> http://www.rhodes22.org/pipermail/rhodes22-list/attch/200507/14/Getaway1.jpg >>> http://www.rhodes22.org/pipermail/rhodes22-list/attch/200507/14/Getaway2.jpg >>> >>> >>> >>> -----Original Message----- >>> From: rhodes22-list-bounces at rhodes22.org >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Ric Stott >>> Sent: Thursday, March 06, 2014 2:00 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] Searching the archives and settled >>> step >now >>> mast step cb leak >>> >>> Thanks Graham >>> It might have been cracked when they loaded it onto a trailer to >>> launch >>> last >>> spring and delivered it to me. >>> It was a transport trailer. >>> Sam replied that the pendant had to be cleated when trailered, or >>> it would >>> cause a crack. >>> I'd like to understand the mechanics of that reply. >>> Is the top or aft edge of the CB that close to the cap, and what >>> component >>> would allow it to move vertically, a hinge pin? >>> Is there a CB diagram anywhere? >>> I think it was leaking, but very little until later in the season >>> then >>> - after a storm, it got much worse. >>> The boat may have been on the bottom or bounced on the bottom at a >>> very >>> low >>> tide. >>> I'll take it apart when it warms up. >>> Pendant - Braided nylon is very stretchy - is that what we want? >>> Ric >>> >>> On Mar 6, 2014, at 1:24 PM, Graham Stewart wrote: >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go >>> to >>> http://www.rhodes22.org/list >>> __________________________________________________ >>> >>> >>> --- >>> This email is free from viruses and malware because avast! Antivirus >>> protection is active. >>> http://www.avast.com >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go >>> to http://www.rhodes22.org/list >>> __________________________________________________ >>> >> >> __________________________________________________ >> To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and >> archives go to http://www.rhodes22.org/list >> __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 