< prior
Back to Month
Go to Thread
2014-07-12; 08:47:35 EDT
Member Since
2014-05-06
Posts: 3821
My heart goes out to you Graham. As I write this, I am sitting on my boat sipping fresh perc'd organic coffee having spent another glorious night sleeping on a mooring @ Salem Willows Yacht Club in Salem, MA. We had a lovely sail here on Wednesday and will head home to SYC today. May you sail again soon. Stephen Staum s/v Carol Lee 2 Needham, MA Sent from my iPhoneSee the original archive post
On Jul 11, 2014, at 10:25 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > I have been putting my boat lift to good use the last week. I am stripping > the bottom paint, which is a miserable job under any circumstance but being > able to do so while sitting on a bar stool makes is immeasurably more > comfortable. I used copious amounts of "safe" paint remover (West Marine) > and a carbon blade scraper (Sandvic) to get most of the paint off. Regular > steel bladed paint scrapers are almost useless. I still have to go at it > with sandpaper to remove the last 10%. > > The paint remover will dry faster than it will soften the paint in 80 degree > weather. When it dries it stops working and you then have to remove the hard > paint remover. The best solution I found was to coat the bottom in sections > of about 4' and then cover it with plastic film. Heavy film (6 mil) falls > off with its own weight while 2 mil stuff stays in place. With the plastic > you can leave it to work for well over 24 hours. I had to do this at least 3 > times to get to the point where I will sand. It is a totally dirty, > stinking, exhausting job. My arms were dropping off after the first hour - > and there were at least 20 hours after that to really make me miserable. > > In removing the paint I have found lots of blisters which I assume are > osmotic blisters. Most a quite small and none have any fluid or space behind > them. In some areas the gelcoat has dozens of mini blisters within a patch > of about 6 square inches. Has anyone seen this? I expect that the > blistering is worse than it looks as the boat has been out of the water for > over three years. Has anyone tackled this problem with their boat? > > After I grind out the blisters and fix with epoxy I intend to put on > multiple epoxy barrier coats. > > I plan to raise the waterline by 2" as some of the blisters are above the > current waterline. My boat seemed to sit stern down as the actual waterline > was higher than the painted waterline. Of course that could be from weight > in the stern but I don't think I have anything there that you would not > expect to find such as the motor. I want to make sure that any part of the > hull that sits below water has the epoxy protection so I am adjusting the > waterline to something just above where the boat actually rests in the > water. > > Finding the new waterline can be a difficult task but by having the front > and rear slings on the lift operating independently with chain hoists I am > able to level the boat quite easily fore and aft. I then used my rotary > laser level ($60 at Home Depot) first to align with the existing waterline > and then cranked it up 2" to locate the new line. This seemed to work pretty > well and I am happy that the lines on the port and starboard meet perfectly > at the bow and in the same plane at the transom. > > I discovered that the original lines were not located in the same place port > and starboard and where they meet the transom were not in the same plane so > that the waterline across the transom was not level. I probably never > noticed before as boats are always listing anyway but when it comes to > locating a new line that difference can be a real pain. The lines seemed to > go off for the last 3 feet at the stern so I was able to use the rest of the > boat to align the rotary laser with the existing waterline, crank up the > level 2" and then take the lines trough at the stern. > > BTW, I discovered that if you want to raise the waterline exactly 2" and > have it work out evenly on both sides, you can't just measure up 2" from the > old line. If you measure up on both sides at exactly the same place it might > come out the same on both sides but it definitely will not be exactly 2". To > get that right I dropped a ruler vertically at the side of the boat and > aligned the 2" mark with the laser and then marked the new position where > the ruler end touched the hull. I then used the new mark to align the rotary > laser to and from there marked the rest of the hull. This is definitely a > summer job as the laser light in these armature tools is quite weak for > outdoor use and the line cannot be seen until dusk. You can rent commercial > units that are much brighter but I already had the unit from when I > installed a suspended ceiling. > > Once the paint is completely removed, blisters filled and the hull faired > and ready for epoxy I will tackle the repair of the outside of the keel. > Finally, I will try to get access to the inside of the keel with a view to > removing and replacing ballast and making structural repairs to the keel > from the inside. All that depends on what I actually find inside the keel > and whether it is practical or even possible to remove what is there. > > These jobs just get worse. > > Graham > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: July-11-14 8:39 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Motor winch > > One option also is to purchase one of these things and wire it into your > winch. At only 23.00 + shipping, it is a really inexpensive solution. > > http://www.amazon.com/Pilot-Performance-Lighting-PL-SW29-Wireless/dp/B000BRJ > F62/ref=sr_1_1?s=automotive&ie=UTF8&qid=1333130375&sr=1-1 > > James > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: Friday, July 11, 2014 7:04 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Motor winch > > Does anyone have an idea of how long to expect the remotes to work? Stan I > don't know if this is a newer feature on the Rhodes and no one has prolonged > experience or if the remotes last for years. > > John Waldhausen > Sent from my iPad > >> On Jul 11, 2014, at 2:54 PM, The Rhodes 22 Email List > <rhodes22-list at rhodes22.org> wrote: >> >> I have the Chicago Electric Power Tools Model 95912 12 volt electric >> winch from Harbor Freight and have searched far and wide for a new >> remote... no luck. Stan said he has no replacement. I ended up buying >> what may have been the last winch on the market from an ebay seller. I >> figured if I lose my remote I can just install the new winch (which >> also came with a remote). I tested the new remote with my current >> winch and it doesn't work so I assume each remote came with a code >> matched > to its specific winch. >> >> You could consider installing a wired winch remote. I believe I saw >> explanations on how to do this somewhere on the Internet. Good luck. >> >> PS: I keep a Schaefer BoomVang Kit on board that I could quickly >> install between the stern rail and the motor in case I drop my remote >> overboard or my winch motor quits. >> >> Geoff >> >> >> On Fri, Jul 11, 2014 at 4:16 PM, The Rhodes 22 Email List < >> rhodes22-list at rhodes22.org> wrote: >> >>> Dear all >>> I have a Rhodes with the Chicago power tools remote control winch to >>> raise and lower the motor. It comes from Harbor freight. I have >>> searched both company websites to find a replacement remote. I cannot >>> find one. ( my original works but is corroding) does anyone know >>> where to obtain a replacement? >>> >>> John Waldhausen >>> Bainbridge island >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 