< prior
Back to Month
Go to Thread
2014-07-12; 14:17:25 EDT
Member Since
2014-05-06
Posts: 3821
Stephen: Your sympathy overwhelms me. Don't get too cocky though, all boats eventually need their bottoms done. GrahamSee the original archive post
-----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: July-12-14 8:48 AM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] boat lift and bottom repair update My heart goes out to you Graham. As I write this, I am sitting on my boat sipping fresh perc'd organic coffee having spent another glorious night sleeping on a mooring @ Salem Willows Yacht Club in Salem, MA. We had a lovely sail here on Wednesday and will head home to SYC today. May you sail again soon. Stephen Staum s/v Carol Lee 2 Needham, MA Sent from my iPhone On Jul 11, 2014, at 10:25 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > I have been putting my boat lift to good use the last week. I am > stripping the bottom paint, which is a miserable job under any > circumstance but being able to do so while sitting on a bar stool > makes is immeasurably more comfortable. I used copious amounts of > "safe" paint remover (West Marine) and a carbon blade scraper > (Sandvic) to get most of the paint off. Regular steel bladed paint > scrapers are almost useless. I still have to go at it with sandpaper to remove the last 10%. > > The paint remover will dry faster than it will soften the paint in 80 > degree weather. When it dries it stops working and you then have to > remove the hard paint remover. The best solution I found was to coat > the bottom in sections of about 4' and then cover it with plastic > film. Heavy film (6 mil) falls off with its own weight while 2 mil > stuff stays in place. With the plastic you can leave it to work for > well over 24 hours. I had to do this at least 3 times to get to the > point where I will sand. It is a totally dirty, stinking, exhausting > job. My arms were dropping off after the first hour - and there were at least 20 hours after that to really make me miserable. > > In removing the paint I have found lots of blisters which I assume are > osmotic blisters. Most a quite small and none have any fluid or space > behind them. In some areas the gelcoat has dozens of mini blisters > within a patch of about 6 square inches. Has anyone seen this? I > expect that the blistering is worse than it looks as the boat has been > out of the water for over three years. Has anyone tackled this problem with their boat? > > After I grind out the blisters and fix with epoxy I intend to put on > multiple epoxy barrier coats. > > I plan to raise the waterline by 2" as some of the blisters are above > the current waterline. My boat seemed to sit stern down as the actual > waterline was higher than the painted waterline. Of course that could > be from weight in the stern but I don't think I have anything there > that you would not expect to find such as the motor. I want to make > sure that any part of the hull that sits below water has the epoxy > protection so I am adjusting the waterline to something just above > where the boat actually rests in the water. > > Finding the new waterline can be a difficult task but by having the > front and rear slings on the lift operating independently with chain > hoists I am able to level the boat quite easily fore and aft. I then > used my rotary laser level ($60 at Home Depot) first to align with the > existing waterline and then cranked it up 2" to locate the new line. > This seemed to work pretty well and I am happy that the lines on the > port and starboard meet perfectly at the bow and in the same plane at the transom. > > I discovered that the original lines were not located in the same > place port and starboard and where they meet the transom were not in > the same plane so that the waterline across the transom was not level. > I probably never noticed before as boats are always listing anyway but > when it comes to locating a new line that difference can be a real > pain. The lines seemed to go off for the last 3 feet at the stern so I > was able to use the rest of the boat to align the rotary laser with > the existing waterline, crank up the level 2" and then take the lines trough at the stern. > > BTW, I discovered that if you want to raise the waterline exactly 2" > and have it work out evenly on both sides, you can't just measure up > 2" from the old line. If you measure up on both sides at exactly the > same place it might come out the same on both sides but it definitely > will not be exactly 2". To get that right I dropped a ruler vertically > at the side of the boat and aligned the 2" mark with the laser and > then marked the new position where the ruler end touched the hull. I > then used the new mark to align the rotary laser to and from there > marked the rest of the hull. This is definitely a summer job as the > laser light in these armature tools is quite weak for outdoor use and > the line cannot be seen until dusk. You can rent commercial units that > are much brighter but I already had the unit from when I installed a suspended ceiling. > > Once the paint is completely removed, blisters filled and the hull > faired and ready for epoxy I will tackle the repair of the outside of the keel. > Finally, I will try to get access to the inside of the keel with a > view to removing and replacing ballast and making structural repairs > to the keel from the inside. All that depends on what I actually find > inside the keel and whether it is practical or even possible to remove what is there. > > These jobs just get worse. > > Graham > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email List > Sent: July-11-14 8:39 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Motor winch > > One option also is to purchase one of these things and wire it into > your winch. At only 23.00 + shipping, it is a really inexpensive solution. > > http://www.amazon.com/Pilot-Performance-Lighting-PL-SW29-Wireless/dp/B > 000BRJ > F62/ref=sr_1_1?s=automotive&ie=UTF8&qid=1333130375&sr=1-1 > > James > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email List > Sent: Friday, July 11, 2014 7:04 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Motor winch > > Does anyone have an idea of how long to expect the remotes to work? > Stan I don't know if this is a newer feature on the Rhodes and no one > has prolonged experience or if the remotes last for years. > > John Waldhausen > Sent from my iPad > >> On Jul 11, 2014, at 2:54 PM, The Rhodes 22 Email List > <rhodes22-list at rhodes22.org> wrote: >> >> I have the Chicago Electric Power Tools Model 95912 12 volt electric >> winch from Harbor Freight and have searched far and wide for a new >> remote... no luck. Stan said he has no replacement. I ended up buying >> what may have been the last winch on the market from an ebay seller. >> I figured if I lose my remote I can just install the new winch (which >> also came with a remote). I tested the new remote with my current >> winch and it doesn't work so I assume each remote came with a code >> matched > to its specific winch. >> >> You could consider installing a wired winch remote. I believe I saw >> explanations on how to do this somewhere on the Internet. Good luck. >> >> PS: I keep a Schaefer BoomVang Kit on board that I could quickly >> install between the stern rail and the motor in case I drop my remote >> overboard or my winch motor quits. >> >> Geoff >> >> >> On Fri, Jul 11, 2014 at 4:16 PM, The Rhodes 22 Email List < >> rhodes22-list at rhodes22.org> wrote: >> >>> Dear all >>> I have a Rhodes with the Chicago power tools remote control winch to >>> raise and lower the motor. It comes from Harbor freight. I have >>> searched both company websites to find a replacement remote. I >>> cannot find one. ( my original works but is corroding) does anyone >>> know where to obtain a replacement? >>> >>> John Waldhausen >>> Bainbridge island >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and >> archives go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 