< prior
Back to Month
Go to Thread
2014-07-12; 14:25:30 EDT
Member Since
2014-05-06
Posts: 3821
Rummy: Rummy: I tried the plastic wrap too but it is unmanageable - especially when wearing sticky gloves, It sticks to itself before you can spread it out. You want the heaviest sheeting that still light enough that it will cling to the paint remover on an overhead surface. I found that the 2 mill stuff worked well while the heavy 6 mil stuff was too heavy. It clings to the surface and is still manageable. GrahamSee the original archive post
-----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: July-12-14 7:48 AM To: rhodes22-list at rhodes22.org Subject: Re: [Rhodes22-list] boat lift and bottom repair update Graham, You certainly have taken on a major project, but I can relate to working in hot weather. I pulled the wife's Chaparral SSI 204 out of the water yesterday and changed fluids in the lower unit and the engine oil. Of course I chose a 95 degree day to do it. NOT FUN. A little cleaning and buffing and I will have it back in the water later today. I liked your idea of using thin plastic to keep the paint remover wet. Saran wrap makes a self clinging plastic wrap which might be what you need. It clings to itself giving you a air tight overlap seam. My 88 Rhodes has had major bottom work done to it twice. Both times were done by highly professional shops, but the itty bitty blisters keep returning. They don't hold any water and don't appear to have gone very deep and certainly haven't gotten into the fiberglass itself. This time I'm going to pressure wash. Sand smooth and simply put another layer of bottom paint on it and go sailing. Rummy In a message dated 7/11/2014 10:25:47 P.M. Eastern Daylight Time, rhodes22-list at rhodes22.org writes: I have been putting my boat lift to good use the last week. I am stripping the bottom paint, which is a miserable job under any circumstance but being able to do so while sitting on a bar stool makes is immeasurably more comfortable. I used copious amounts of "safe" paint remover (West Marine) and a carbon blade scraper (Sandvic) to get most of the paint off. Regular steel bladed paint scrapers are almost useless. I still have to go at it with sandpaper to remove the last 10%. The paint remover will dry faster than it will soften the paint in 80 degree weather. When it dries it stops working and you then have to remove the hard paint remover. The best solution I found was to coat the bottom in sections of about 4' and then cover it with plastic film. Heavy film (6 mil) falls off with its own weight while 2 mil stuff stays in place. With the plastic you can leave it to work for well over 24 hours. I had to do this at least 3 times to get to the point where I will sand. It is a totally dirty, stinking, exhausting job. My arms were dropping off after the first hour - and there were at least 20 hours after that to really make me miserable. In removing the paint I have found lots of blisters which I assume are osmotic blisters. Most a quite small and none have any fluid or space behind them. In some areas the gelcoat has dozens of mini blisters within a patch of about 6 square inches. Has anyone seen this? I expect that the blistering is worse than it looks as the boat has been out of the water for over three years. Has anyone tackled this problem with their boat? After I grind out the blisters and fix with epoxy I intend to put on multiple epoxy barrier coats. I plan to raise the waterline by 2" as some of the blisters are above the current waterline. My boat seemed to sit stern down as the actual waterline was higher than the painted waterline. Of course that could be from weight in the stern but I don't think I have anything there that you would not expect to find such as the motor. I want to make sure that any part of the hull that sits below water has the epoxy protection so I am adjusting the waterline to something just above where the boat actually rests in the water. Finding the new waterline can be a difficult task but by having the front and rear slings on the lift operating independently with chain hoists I am able to level the boat quite easily fore and aft. I then used my rotary laser level ($60 at Home Depot) first to align with the existing waterline and then cranked it up 2" to locate the new line. This seemed to work pretty well and I am happy that the lines on the port and starboard meet perfectly at the bow and in the same plane at the transom. I discovered that the original lines were not located in the same place port and starboard and where they meet the transom were not in the same plane so that the waterline across the transom was not level. I probably never noticed before as boats are always listing anyway but when it comes to locating a new line that difference can be a real pain. The lines seemed to go off for the last 3 feet at the stern so I was able to use the rest of the boat to align the rotary laser with the existing waterline, crank up the level 2" and then take the lines trough at the stern. BTW, I discovered that if you want to raise the waterline exactly 2" and have it work out evenly on both sides, you can't just measure up 2" from the old line. If you measure up on both sides at exactly the same place it might come out the same on both sides but it definitely will not be exactly 2". To get that right I dropped a ruler vertically at the side of the boat and aligned the 2" mark with the laser and then marked the new position where the ruler end touched the hull. I then used the new mark to align the rotary laser to and from there marked the rest of the hull. This is definitely a summer job as the laser light in these armature tools is quite weak for outdoor use and the line cannot be seen until dusk. You can rent commercial units that are much brighter but I already had the unit from when I installed a suspended ceiling. Once the paint is completely removed, blisters filled and the hull faired and ready for epoxy I will tackle the repair of the outside of the keel. Finally, I will try to get access to the inside of the keel with a view to removing and replacing ballast and making structural repairs to the keel from the inside. All that depends on what I actually find inside the keel and whether it is practical or even possible to remove what is there. These jobs just get worse. Graham -----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: July-11-14 8:39 PM To: 'The Rhodes 22 Email List' Subject: Re: [Rhodes22-list] Motor winch One option also is to purchase one of these things and wire it into your winch. At only 23.00 + shipping, it is a really inexpensive solution. http://www.amazon.com/Pilot-Performance-Lighting-PL-SW29-Wireless/dp/B000BRJ F62/ref=sr_1_1?s=automotive&ie=UTF8&qid=1333130375&sr=1-1 James -----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: Friday, July 11, 2014 7:04 PM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] Motor winch Does anyone have an idea of how long to expect the remotes to work? Stan I don't know if this is a newer feature on the Rhodes and no one has prolonged experience or if the remotes last for years. John Waldhausen Sent from my iPad > On Jul 11, 2014, at 2:54 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > I have the Chicago Electric Power Tools Model 95912 12 volt electric > winch from Harbor Freight and have searched far and wide for a new > remote... no luck. Stan said he has no replacement. I ended up buying > what may have been the last winch on the market from an ebay seller. > I figured if I lose my remote I can just install the new winch (which > also came with a remote). I tested the new remote with my current > winch and it doesn't work so I assume each remote came with a code > matched to its specific winch. > > You could consider installing a wired winch remote. I believe I saw > explanations on how to do this somewhere on the Internet. Good luck. > > PS: I keep a Schaefer BoomVang Kit on board that I could quickly > install between the stern rail and the motor in case I drop my remote > overboard or my winch motor quits. > > Geoff > > > On Fri, Jul 11, 2014 at 4:16 PM, The Rhodes 22 Email List < > rhodes22-list at rhodes22.org> wrote: > >> Dear all >> I have a Rhodes with the Chicago power tools remote control winch to >> raise and lower the motor. It comes from Harbor freight. I have >> searched both company websites to find a replacement remote. I >> cannot find one. ( my original works but is corroding) does anyone >> know where to obtain a replacement? >> >> John Waldhausen >> Bainbridge island >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and >> archives go to http://www.rhodes22.org/list >> __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and > archives go to http://www.rhodes22.org/list > __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 