< prior
Back to Month
Go to Thread
2014-07-13; 10:27:11 EDT
Member Since
2014-05-06
Posts: 3821
Thanks Graham. Now I feel a sense of impending doom. & so soon after a lovely sailing vacation. Stephen Staum s/v Carol Lee 2 Needham, MA Sent from my iPhoneSee the original archive post
On Jul 12, 2014, at 2:17 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > Stephen: > Your sympathy overwhelms me. Don't get too cocky though, all boats > eventually need their bottoms done. > > Graham > > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: July-12-14 8:48 AM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] boat lift and bottom repair update > > My heart goes out to you Graham. As I write this, I am sitting on my boat > sipping fresh perc'd organic coffee having spent another glorious night > sleeping on a mooring @ Salem Willows Yacht Club in Salem, MA. We had a > lovely sail here on Wednesday and will head home to SYC today. > > May you sail again soon. > > Stephen Staum > s/v Carol Lee 2 > Needham, MA > > Sent from my iPhone > > On Jul 11, 2014, at 10:25 PM, The Rhodes 22 Email List > <rhodes22-list at rhodes22.org> wrote: > >> I have been putting my boat lift to good use the last week. I am >> stripping the bottom paint, which is a miserable job under any >> circumstance but being able to do so while sitting on a bar stool >> makes is immeasurably more comfortable. I used copious amounts of >> "safe" paint remover (West Marine) and a carbon blade scraper >> (Sandvic) to get most of the paint off. Regular steel bladed paint >> scrapers are almost useless. I still have to go at it with sandpaper to > remove the last 10%. >> >> The paint remover will dry faster than it will soften the paint in 80 >> degree weather. When it dries it stops working and you then have to >> remove the hard paint remover. The best solution I found was to coat >> the bottom in sections of about 4' and then cover it with plastic >> film. Heavy film (6 mil) falls off with its own weight while 2 mil >> stuff stays in place. With the plastic you can leave it to work for >> well over 24 hours. I had to do this at least 3 times to get to the >> point where I will sand. It is a totally dirty, stinking, exhausting >> job. My arms were dropping off after the first hour - and there were at > least 20 hours after that to really make me miserable. >> >> In removing the paint I have found lots of blisters which I assume are >> osmotic blisters. Most a quite small and none have any fluid or space >> behind them. In some areas the gelcoat has dozens of mini blisters >> within a patch of about 6 square inches. Has anyone seen this? I >> expect that the blistering is worse than it looks as the boat has been >> out of the water for over three years. Has anyone tackled this problem > with their boat? >> >> After I grind out the blisters and fix with epoxy I intend to put on >> multiple epoxy barrier coats. >> >> I plan to raise the waterline by 2" as some of the blisters are above >> the current waterline. My boat seemed to sit stern down as the actual >> waterline was higher than the painted waterline. Of course that could >> be from weight in the stern but I don't think I have anything there >> that you would not expect to find such as the motor. I want to make >> sure that any part of the hull that sits below water has the epoxy >> protection so I am adjusting the waterline to something just above >> where the boat actually rests in the water. >> >> Finding the new waterline can be a difficult task but by having the >> front and rear slings on the lift operating independently with chain >> hoists I am able to level the boat quite easily fore and aft. I then >> used my rotary laser level ($60 at Home Depot) first to align with the >> existing waterline and then cranked it up 2" to locate the new line. >> This seemed to work pretty well and I am happy that the lines on the >> port and starboard meet perfectly at the bow and in the same plane at the > transom. >> >> I discovered that the original lines were not located in the same >> place port and starboard and where they meet the transom were not in >> the same plane so that the waterline across the transom was not level. >> I probably never noticed before as boats are always listing anyway but >> when it comes to locating a new line that difference can be a real >> pain. The lines seemed to go off for the last 3 feet at the stern so I >> was able to use the rest of the boat to align the rotary laser with >> the existing waterline, crank up the level 2" and then take the lines > trough at the stern. >> >> BTW, I discovered that if you want to raise the waterline exactly 2" >> and have it work out evenly on both sides, you can't just measure up >> 2" from the old line. If you measure up on both sides at exactly the >> same place it might come out the same on both sides but it definitely >> will not be exactly 2". To get that right I dropped a ruler vertically >> at the side of the boat and aligned the 2" mark with the laser and >> then marked the new position where the ruler end touched the hull. I >> then used the new mark to align the rotary laser to and from there >> marked the rest of the hull. This is definitely a summer job as the >> laser light in these armature tools is quite weak for outdoor use and >> the line cannot be seen until dusk. You can rent commercial units that >> are much brighter but I already had the unit from when I installed a > suspended ceiling. >> >> Once the paint is completely removed, blisters filled and the hull >> faired and ready for epoxy I will tackle the repair of the outside of the > keel. >> Finally, I will try to get access to the inside of the keel with a >> view to removing and replacing ballast and making structural repairs >> to the keel from the inside. All that depends on what I actually find >> inside the keel and whether it is practical or even possible to remove > what is there. >> >> These jobs just get worse. >> >> Graham >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email List >> Sent: July-11-14 8:39 PM >> To: 'The Rhodes 22 Email List' >> Subject: Re: [Rhodes22-list] Motor winch >> >> One option also is to purchase one of these things and wire it into >> your winch. At only 23.00 + shipping, it is a really inexpensive > solution. >> >> http://www.amazon.com/Pilot-Performance-Lighting-PL-SW29-Wireless/dp/B >> 000BRJ >> F62/ref=sr_1_1?s=automotive&ie=UTF8&qid=1333130375&sr=1-1 >> >> James >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email List >> Sent: Friday, July 11, 2014 7:04 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Motor winch >> >> Does anyone have an idea of how long to expect the remotes to work? >> Stan I don't know if this is a newer feature on the Rhodes and no one >> has prolonged experience or if the remotes last for years. >> >> John Waldhausen >> Sent from my iPad >> >>> On Jul 11, 2014, at 2:54 PM, The Rhodes 22 Email List >> <rhodes22-list at rhodes22.org> wrote: >>> >>> I have the Chicago Electric Power Tools Model 95912 12 volt electric >>> winch from Harbor Freight and have searched far and wide for a new >>> remote... no luck. Stan said he has no replacement. I ended up buying >>> what may have been the last winch on the market from an ebay seller. >>> I figured if I lose my remote I can just install the new winch (which >>> also came with a remote). I tested the new remote with my current >>> winch and it doesn't work so I assume each remote came with a code >>> matched >> to its specific winch. >>> >>> You could consider installing a wired winch remote. I believe I saw >>> explanations on how to do this somewhere on the Internet. Good luck. >>> >>> PS: I keep a Schaefer BoomVang Kit on board that I could quickly >>> install between the stern rail and the motor in case I drop my remote >>> overboard or my winch motor quits. >>> >>> Geoff >>> >>> >>> On Fri, Jul 11, 2014 at 4:16 PM, The Rhodes 22 Email List < >>> rhodes22-list at rhodes22.org> wrote: >>> >>>> Dear all >>>> I have a Rhodes with the Chicago power tools remote control winch to >>>> raise and lower the motor. It comes from Harbor freight. I have >>>> searched both company websites to find a replacement remote. I >>>> cannot find one. ( my original works but is corroding) does anyone >>>> know where to obtain a replacement? >>>> >>>> John Waldhausen >>>> Bainbridge island >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and >>>> archives go to http://www.rhodes22.org/list >>>> __________________________________________________ >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 