2014-07-20; 20:19:23 EDT
Member Since
2014-05-06
Posts: 3821
I am thinking that it might be of interest to some of the Rhodes owners if I document my work and ideas as I continue with the restoration of Ariel. Having removed all of the thru hull fittings on my boat and also having removed the bottom paint I have a couple of observation that those with older boats might find useful. Mine is a 1976. Hull thickness at about 12" from the centreline is about 3/16th" thick - including the gel coat. I have no idea what thickness is ideal but this "looks" a bit on the thin side to me. Where the hull rested on the forward end of the trailer bunk on the starboard side I noticed that the hull had deformed quite noticeably. A few years back I raised the boat on the trailer to take the pressure off at that point and slowly the hull returned most of the way, but not entirely, to its original position. This raised the question in my mind as to the thickness of the board located under the keel on the RC trailers. In my case the original board is missing and replaced with a 1.5" thick board. If anyone can confirm the thickness of the original board I would appreciate knowing what it is. Otherwise I think I will double the board thickness to 3". On inspecting the hull with the bottom paint removed I noticed an array of hairline cracks in the gelcoat where the deformation occurred. The deformation tends to confirm for me that the scantlings were a bit on the light side and this seems to be further confirmed by the General Boats website where Stan reports that this trailer deformation was a problem with earlier boats and as a result later boats were built with thicker hulls. It would be nice to know how much thicker they actually are. So I think that I will try to stiffen the boat below the waterline by adding a couple of layers of cloth on the inside of the hull between the V birth and the cockpit where I have access. I have removed all structures from the inside of the boat including the stringers for the floorboards so access is not a problem in the main cabin area. In this case I think it might be better to use polyester rather than epoxy. The only reason I say this is because I read in an article on osmosis repair that if a boat has water pooling in the bilge on a constant basis that one can coat the inside of the hull with epoxy but the article stressed, without explanation, to only coat the area where the water stands. I wonder whether the low porosity of epoxy might be inclined to trap moisture in the hull thereby promoting more osmosis. I have examined the keel sections more carefully including the drilling of a number of holes that allow me to judge to some degree the content of the keel and the feasibility of removing and replacing the ballast material. The material is a mix of lead flakes and some kind of material that is crumbly and soft. There are many large voids in the keel that can be determined by tapping and I confirmed by drilling holes. My examination and more careful measuring suggests that gaining sufficient access to the keel areas from inside the boat to be able to remove the existing ballast and repair the keel cracks from the inside is not feasible. The width of the cavity appears to range from less than 4" at the centre to less than 2" at the ends. Therefore, my plan at this point is to repair the keel by adding at least two layers of cloth and epoxy on the outside and around the bottom and up at least 4" into the slot. The skin at the centre of the keel is very thin and appears to be less than 1/8" so strengthening the keel would not appear to be without merit given the serious cracks that have formed at the bottom of the keel. To address the ballast problem I plan to drill a number of 1.25" holes through the sole into the cavity. I will then try to tamp down what loose material is there by using a rod. I will then add small lead tire balancing weights as best I can and then pour in polyester resin to fill voids and hold the mix in place. I am thinking polyester because it is less than half the cost of epoxy and I believe I can slow down the cure rate and heat by using the minimum amount of hardener - although at this point I have no idea what that minimum would be. I could also control heat be doing the pour in stages. I have confirmed that the ballast that is glassed to the floor of the hull just in front of the mast post is steel bars and based on the dimensions has a volume of .33 cu. Ft. making the weight about 160 lbs. If I am unable to get sufficient weight into the keel I might add additional bars of lead along either side of the centreboard. The problem is that I have no idea what the weight is of the ballast currently remaining in the keel. The boat seemed to me to be very tender and I have always thought that some additional ballast would be helpful so I expect that if I go at this with some caution it should work. If possible I would like to launch the boat after the ballast is added but before it is bonded in place to see how it sits in the water and handles. That said, I would prefer to complete the interior before reinstalling all of the running and standing hardware and stays but perhaps I should rethink that approach. I worry that if I launch the boat before I complete the interior, I might never get it done. As usual, I value any suggestions, cautions etc. GrahamSee the original archive post