2014-08-30; 22:43:36 EDT
Member Since
2014-05-06
Posts: 3821
Finally, after working on the bottom and keel for most of the Summer I finished today except for the spots where the boat is supported on the lift. For those who may be considering the need for osmosis repair, I have a few observations about Interprotect 2000e barrier coating that might be of use. I spent a lot of time trying to decide whether to go with the West System barrier coat or the Interprotect 2000e. I am glad now that I went with the Interprotect. Here are the advantages as I experienced it: - Interprotect goes on like paint. It has a 5 hr pot life (probably more) but dries on the boat very quickly. This I think is a big advantage over the West system where you have to make small batches and work within a narrow window to get it on before it starts to go off. Interprotect is much more forgiving. - Interprotect comes in white and gray. Alternating colours ensures complete coverage and I found that to be surprisingly helpful. - With temperatures in the high 70s I was able to recoat as soon as I finished the previous coat. Interlux says that it should take 3 hrs at that temperature for the coating to dry sufficiently - measured by the fact that you can press your thumb into the coating without any paint transfer to your thumb. It took me about 1 hour to apply a coat with each coat a bit faster than the previous one and once finished the place where I started already was ready for recoating. - I used 3 gallons of Interprotect and was able to apply 6 coats with about 1 quart waste - partly because I was using two colours and that means more waste. The first coat took 3/4 of a gallon and subsequent coats slightly less than 1/2 gallon. - Using the 3/8 nap rollers, as recommended, I was able to get coats that were 3 mils thick. Interlux suggests a total of 10 mils which they say requires 4-5 coats. I put on 6 coats because I already had the paint and was not sure I could trust my film thickness gauge. It appears that I applied about 18 mils so that should be more than adequate. - After the last coat of interprotect I was able to apply the antifouling almost immediately but waited about 1hr in order to have lunch. I hope I didn't delay too long. I used Bottomkote Act for the antifouling primarily because it was rated so well by Practical Sailor. It goes on beautifully over the interprotect and is supposed to bond chemically with it if applied at the right time. I guess I will find out whether my timing was right after I launch. - Interlux tells me to launch within 60 days of applying the antifouling and to apply the antifouling immediately after the interprotect is applied. In my case I can't do both so I applied only the first coat of antifouling and will apply the second before launch. In total the work involved in stripping the old paint, osmosis repair and recoating was gruesome work and took a ridiculous amount of time. Boat repair seems to consist mainly of applying epoxy and then sanding most of it off - usually overhead. Using 3 gallons of polyester resin I and filled the voids in the keel. Hopefully I got most of the voids. I filled the cracks in the keel with thickened epoxy and covered the cracks with 4 lavers of cloth and epoxy. I covered the exterior of the keel with 2 layers of cloth and epoxy and then faired the whole thing with West resin and fairing additives. I used Interlux Watertight fairing for the final imperfections. It is very expensive but wonderful to work with as it applies so easily and sands easily without amine blush. In the end it is probably cheaper than West for these small repairs as you can make up much smaller batches than is possible with West. Using the 3M 3030 masking tape for the water line worked very well. I had it on the boat in the sun for well over a month and it came off very cleanly with no residue. It was unaffected by the epoxy. It was removed about 30 hrs after the first coat of epoxy barrier coat was applied. The edge is not as sharp as blue masking tape but it is surprisingly good and I am happy with the result. Being able to leave it on the boat for up to 90 days was a real benefit. I am so glad to get that part done. Now I need to remove the supports from the lift so I can apply the interprotect and antifouling to those spots. I hope to do that tomorrow if the weather cooperates. Then the boat will be removed from the lift and returned to the temporary shelter for the winter and eventual completion I have been in a rush to complete this stage as I am going to the UK for most of September and wanted the boat out of the lift before I leave next Wednesday. Past September it will likely be too cold to do any of this type of work. The cut thumb is pretty much healed except that one half has no feeling at all and the other half is constantly burning. Otherwise I am able to use it now that I am learning to judge pressure without feeling. The good news was that it was my left hand. The bad news is that I am left handed. I heard on the radio the day after my attempted self-amputation that home amputations have become most common and typically involve a band saw and the victim is the thumb on the dominant hand. So it appears that my attempt was quite trendy, if not entirely successful, for which I am grateful. Be warned, it doesn't take much of a slip to do a lot of damage with a band saw. Graham _____________________ Barrier coat and Antofouling applied Aug 30, 2014.jpgSee the original archive post