2014-10-29; 22:27:51 EDT
Member Since
2014-05-06
Posts: 3821
Well, if its nice tomorrow, I might start drilling and probing. I've been reading on this all afternoon and most people only have problems around the fittings and hatches. Mine looks like the whole thing... I appreciate all your help.Now, if I understand this, as I drill down, I should have a layer of fiberglass and the core. Then under the hole should be the lower layer of fiberglass and under that the cabin liner right?
I wanted to learn this fiberglassing.... looks like I might be doing it in a major way.....
Thanks Graham,
Brad Bachelor
Marrying an old bachelor is like buying second-hand furniture. -- Helen Rowland 1875-1950, American Journalist
From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org>
To: 'The Rhodes 22 Email List' <rhodes22-list at rhodes22.org>
Sent: Wednesday, October 29, 2014 8:00 PM
Subject: Re: [Rhodes22-list] My new toy.... Talk me into saving it
You deck looks much worse than mine was. I would start by drilling fairly large holes down to be not through the liner and carefully examine the core material that the drill bit extracts. If it is wet, injected epoxy will be useless and the only course open to you that I can think of is to remove the core and replace it with good material. You should drill a systematic pattern to make sure you don't miss any areas - every 4" should be good. While you are at it, check out the side decks and cabin top. If they are punky too, then I think the boat should be considered a write-off. By the way, I had a surveyor check my deck with a moisture meter but that turned out to not be an accurate indication of the actual situation.
In my case the only area that was wet was about a square foot around the air vent near the bow but I didn't know that until I removed the deck and separated the deck skin from the liner. I just assumed that if the deck was soft it must be rotten.
The plywood core had delaminated from the skin and even the different plys had separated. The bond between the plywood core and the deck skin was very poor amounting to what looked like random strips of silicone and with time and flexing of the deck it simply let go. Certainly removing the deck and recoreing it - or doing this without removing the deck will give the best results.
Taking the sag out of your deck might be difficult. If the core is solid and just delaminated, and I doubt that it is, you might put jacks inside the boat to see if you can push it back and hold it there while you inject the epoxy. If you decide to remove the deck, you can set up a frame of some sort to hold the outer skin in place while you place and laminate the new core.
At one point I was trying to devise a system to press up on the deck to adjust its shape while it was on the boat and came up with a simple system that used a frame with vertical 2x4s into which I screwed heavy lad screws into the end of each upright piece. I then put scratch pads on the head of the lag screw to avoid damaging the liner. I placed the frame on the V-birth and buy unscrewing the lag screw I was able to exert considerable pressure upwards in very fine increments - without spending a fortune of jacks. I have attached a photo that shows some of these lag screw jacks. My intention was to use this system to bend the deck at the join to fit the shape of the deck on the other side of the join. With the new core the deck was far too rigid for this to work, but in your case it might be worth considering.
Removing the foredeck in my case was remarkably easy. I removed the rub rail, cut through the deck in front of the cabin with a circular saw, drilled out the rivets that joined the hull and deck and was able to break the seal fairly easily. The deck then just lifted off in my hands. Most of the time was taken up just trying to get up the nerve to cut across the deck but in my case, like yours, I felt that once I had removed the deck and pulled the layers apart I would know better what I was in for while not investing anything thus far. If it was not reparable then it would go to the dump anyway so there wasn't much to lose.
Once the deck is removed you can examine the cut edge in front of the cabin and see if there is rot there. If there is then you may find that it is all too far gone.
As I mentioned, getting the deck off and rebuilding it with a new core and reinstalling the liner was not all that difficult. What was far more difficult was putting the darned thing back on so that it didn't look like Frankenstein. That required a lot of grinding and filling to make the join invisible - especially for me as at that point I had never done anything like that before and so I wasted a lot of time getting it right. If you have any body work experience it would go faster. The last picture was taken after the deck was reinstalled and the fairing completed but before it was glassed over and painted.
If you do remove the deck to replace the core, you will need to set up some kind of form to hold the deck skin in the shape you want it to be when you are finished. Bonding plywood will make the deck completely rigid and you will not be able to shape it to fit afterwards. In my case the form was a very simple T with the cross piece shaped to the curve that I took from the deck in front of the cabin. Given the deck distortion in your situation you might need something with more crosspieces. I have attached two pictures - one of the form and the other of the deck in the form after reinstalling the liner. I built up the core using layers of 1/8" marine plywood - with epoxy sealing all surfaces and thickened epoxy bonding the layers. I had to temporarily screw each layer right down through the deck in order to make it take the shape as well as use timbers to clamp the whole thing to the frame. That obviously put lots of holes in the deck but given that I knew I would need repai!
r the deck anyway, that didn't matter.
Once the deck was reinstalled, I covered the entire non-skid area of the entire fore and side decks with a layer of cloth to cover all of the holes and then filed and faired the whole thing until it looked right. Doing the gunwales was the hard part but I won't bother you with the details unless you actually decide to plunge in. I have more photos of the steps and tools that I developed to do this work if you would like them.
Enough for now. If you decide to go further I am happy to share my experience as it would be comforting to think that I was not the only person out there who would do such a thing.
Although it made no sense from either a financial or time perspective to do this, I am pretty happy about how the boat is turning out and am still glad that I decided to do it. Better than watching endless games of hockey over those years.
Graham
070.JPG
069.JPG
See the original archive post