< prior
Back to Month
Go to Thread
2014-12-08; 21:09:23 EST
Member Since
2014-05-06
Posts: 3821
Hi: Look way at the bottom. This is where attachments sometimes end up in gmail. And sometimes nabble gets funky. Cheers, Shawn s/v Sweet Baboo (Recycled 86)See the original archive post
On Mon, Dec 8, 2014 at 6:03 PM, The Rhodes 22 Email List < rhodes22-list at rhodes22.org> wrote: > I would like to see the drawing, but didn't find an attachment > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: Monday, December 08, 2014 2:40 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Seam line name > > Chuy: > I have attached a crude drawing of a cross-sectional view of the hull and > deck joint. As you will see, the sealant goes in the space between where > the > hull and deck overlap. Ideally it would be best to remove the rivets in > order to open the gap in order to remove the sealant. That requires the > removal of the rub rail and chances are that the rail will be destroyed in > the process. Once the sealant is forced into the gap the gap is closed with > new rivets or bolts. You would do this in sections rather than all at once. > The easier alternative is to just remove whatever sealant you can from the > join and add sealant at the bottom of the gap but that will be a temporary > fix based on my experience. > > I can't see where putting sealant on either side of the rub rail would > accomplish much of anything other than make a mess. It is the gap that > needs > to be sealed, not the rub rail. > > The rivets on my deck hull join held firmly for 35 years but if I were to > replace them I would probably use bolts and at closer intervals to give > less > movement to the join area. But I have already glassed the join on the > inside > so any hardware is probably redundant anyway. > > I will be interested to see what Rummy's strategy is. > > Graham > > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: December-08-14 12:16 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Seam line name > > Graham: > Yes, the aluminum track with the black plastic. When Stan riveted the > rub > rail, he joined the top half to the bottom half of the boat. So ,there is > a > seam where the top part meets the bottom part. My question refers to how > these two parts meet. Does the top half overlap the bottom, there they are > riveted? On my Rhodes the top half appears to slide down and to the > outside > of the hull half. The rivets are then inserted into the two halves. The > rivets after a time will make the hole larger allowing water to enter the > boat in some cases to enter the cabin or the cockpit. > > Does this sound right to you. I had wanted to redo the aluminum track but > I > do not want to use rivets. Would rather use bolts but there are some areas > where I can not get to the inside to place the nut. I I think screws would > be worst than rivets. A few people replied that they had silicone the top > and bottom of the rail and it seemed to be working. So, I will try it. It > seems to me, that unless the holes get very large the leaks can be > contained > with a seal on the rail. > > I do have another question for you. The doors inside the galley use a > track. You had mentioned that you are using or will be using some track > from Lowe's, can you give me more details on the track you plan on using > and > also the type and thickness of material you plan on using on the top and > bottom galley doors. > > Thank for taking the time to answer all my questions and concerns. > > Happy Holidays, > > Chuy > Rhodes 22 , After-Math > ---- The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > Chuy: > > > > I don't think I understand the question. I don't know what the > > "sheets" are that you are referring to. It may be that your boat has a > > different rub rail than mine and that is the reason I don't > > understand. On my boat the rub rail consists of an aluminium track > > that is screwed to the hull with a black plastic insert that goes into > > the > track. Is this what you are referring to? > > > > > > > > Graham > > > > > > > > -----Original Message----- > > From: rhodes22-list-bounces at rhodes22.org > > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > > Email List > > Sent: December-06-14 9:41 AM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Seam line name > > > > Hi Graham, > > On the rub rail. How are the top and bottom sheets joined? Are > > they butted, overlapping? Some replied that they had to wedge in some > rubber. > > How and where does this rubber go? > > > > Thanks Again, > > Chuy > > > > > > ---- The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > > Chuy: > > > > > > I assume that you are you talking about the hull- deck join? If so > > > the leak will only occur when healing or taking a large wave. The > > > "simplest" solution is to remove the sealant in the join and force > > > new sealant in. Easier said than done. I have used a small wedge to > > > open the join a bit to allow more sealant in. It is important to > > > remove all of the old sealant or the new sealant will not hold for > long. > > > Important, but also virtually impossible so do you best. I have done > > > this several times over 20 years so that might give you some idea of > > > the > > permanence. > > > > > > Picking the right sealant is important and also a matter that can > > > lead to great debates. If you use sealant like 3M 5200 or equivalent > > > you will never get it out again. For hull-deck joins that is usually > > > desirable because of the strength and, if you are putting it on > > > fibreglass that has no silicone trace, want to be permanent. In this > > > case I would anticipate that you might want to redo this fix in the > > > future and would be inclined to use 3M 4200 or equivalent. I would > > > be > > interested to hear from others on this point. > > > > > > Ultimately, because I was doing a major reconstruction and had > > > gutted the entire cabin, I decided to glass the entire join on the > inside. > > > That seals it up "permanently" and gives the hull considerably less > > > flex at the joint which I assume is a good thing. To do that I had > > > to remove the rub rail and the rivets and screws along the join as > > > you don't want to be glassing around these obstacles. When I reach > > > that stage in my reconstruction I will add bolts along the join > > > before replacing the rub rail. If that doesn't fix the leak once and > > > for all, I > > give up. > > > > > > > > > > > > Graham > > > > > > > > > -----Original Message----- > > > From: rhodes22-list-bounces at rhodes22.org > > > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes > > > 22 Email List > > > Sent: December-05-14 9:07 AM > > > To: The Rhodes 22 Email List > > > Subject: [Rhodes22-list] Seam line name > > > > > > Hi All, > > > Have a leak in my Rhodes 22. I think most of the water is coming > > > from the seam where the top skin and bottom skin are joined. First > > > what is that seam called? Second, any ideas on how to repair it? > > > > > > Thanks, > > > Chuy > > > Rhodes 22, After-Math > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and > > > archives go to http://www.rhodes22.org/list > > > __________________________________________________ > > > > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and > > > archives go to http://www.rhodes22.org/list > > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: hull-deck join.jpg > Type: image/jpeg > Size: 103712 bytes > Desc: not available > Url : > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20141208/e2be5eb > 4/attachment.jpg > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 