The Rhodes 22 Discussion Group R22 Discussion Group

The Rhodes 22 Discussion Group


< prior

Back to Month

Go to Thread

Member Picture

The Rhodes 22 Email List



Deck joint repair.

2014-12-09; 11:00:26 EST

Member Since

2014-05-06

Posts: 3821

As expected, Rummy's instructions are spot on excellent. I might add a few
additional bits that he does not mention and Rummy can correct me if I am
wrong.

On my boat (1976) not all of the rivets came all the way through to the
aluminium rub rail. To remove all of the rivets I had to remove the
aluminium rail and I was unable to do that without destroying it as any
bends that you put into the rail cannot be straightened. So plan on
replacing the rub rail with a new one.

The sealant you decide to use might determine how much you should do at one
time. I am not familiar with the sealant Rummy uses but as it is intended
for roofs, I suspect it stays very soft. Perhaps Rummy will advise what
happens to the sealant he uses as it cures. But if you use a sealant that
hardens up when it cures such as any of the marine sealants you will want to
close the gap with rivets or bolts before the sealant cures. If you seal all
the way around the boat and then start adding the rivets the sealant will
cure before you will be able to compress the join. 

You will no doubt find that everyone has strong and differing opinions about
what sealant to use and in the end you will need to go with your best
judgement. Obviously you want a top quality sealant that will last
indefinitely. You will also probably want one that has excellent expansion
capabilities. As the deck and hull expands and shrinks and also flexes, it
is important that the sealant has the ability to tolerate that change. Even
sealant that has excellent elasticity will not work if it is applied too
thin. Boat windows made of Plexiglas and attached to the exterior without
hardware use a combination of special thick double-sided tape and high flex
sealant - usually Dow-Corning 795. The tape is extremely adhesive but also
maintains about a 1/8" gap between the window and the cabin side that allows
the sealant to be thick enough to work properly. The 795 sealant is
extremely flexible but also extremely adhesive. 

The main issue in the case of the hull deck join, in my opinion, is not so
much adhesion, as the rivets will hold the boat together, but rather to
maintain a good permanent and flexible seal. You might consider using butyl
for this (the form that comes in a tube) but because it would add nothing to
the strength of the join I would double up on the rivets/bolts. 

One argument that might favour bolts over rivets is that you can tighten the
bolts as needed while rivets apply maximum pressure. If you want to make
sure that the sealant is not all squeezed out of the join, bolts would give
you that degree of control. With butyl, that should be less of a concern.
There is a lot (too much) of information on the net about the pros and cons
of various sealants. I would be interested to know which sealant Stan would
recommend.

Widen the gap with wooden wedges/shims ahead of where you are injecting the
sealant to ensure that the sealant is injected well into the gap. Put the
shims in first as needed and then remove each as you reach that point with
the sealant. That will allow you to get more sealant into the join and the
removal of the shim will squeeze the sealant immediately while it is still
uncured. 

Another thing I would worry about is removing all of the rivets at once. The
hull is very thin and very flexible at the top and I would worry about the
whole thing changing shape one all of the rivets and sealant has been
removed. Assuming that the boat is on its trailer when you do the job and
knowing that the trailer applies uneven pressure to the hull, I would not
want to find that the boat hull and deck became misaligned. That might not
happen but at the same time you can avoid the risk by doing sections of
about 8' at a time. Remove the rivets in one section only after the previous
section has been sealed and riveted/bolted. Alternatively, replace some of
the rivets (say every 4') temporarily with bolts that can be easily removed
as you work your way around the boat. 

I would definitely add more rivets or bolts to those presently on the boat
especially around the fore deck. I think that the waves on the bow work the
hull-deck join as the hull is very flexible in comparison to the rigid deck
and that is where the sealant can/will break. Certainly on my boat it was
only at the front section that I had trouble with leaks. 

Finally, if you use rivets, I would definitely use washers with them.

Good luck

Graham 


See the original archive post
×

Message to Webmaster:

To use your email application to send a messsage to the webmaster rather than this form, .



×

Post to the Rhodes 22 Email List:



×

Sending Post:

Your post is being sent... waiting