The Rhodes 22 Discussion Group R22 Discussion Group

The Rhodes 22 Discussion Group


< prior

Back to Month

Go to Thread

Member Picture

The Rhodes 22 Email List



Deck joint repair.

2014-12-10; 07:26:47 EST

Member Since

2014-05-06

Posts: 3821

Graham,
The newer boats all use a plastic rub rail. Aluminum was scrapped years  
ago. NP1 sticks to anything it comes in contact with. It is used in roofing  
because it seals during expansion and contraction events. It also has a 15 
year  direct exposure guarantee from the manufacturer. You are correct in that 
you  don't want to apply more than you can install the pop rivets and 
tighten within  an hour or so. It takes several days to fully cure, but becomes 
water tight  after skinning over. It never fully "hardens". 
I did this procedure approximately fifteen years ago on Rumrunner and to  
this day it's still water tight.
 
Rummy
 
 
In a message dated 12/9/2014 11:00:25 A.M. Eastern Standard Time,  
rhodes22-list at rhodes22.org writes:

As  expected, Rummy's instructions are spot on excellent. I might add a  few
additional bits that he does not mention and Rummy can correct me if I  am
wrong.

On my boat (1976) not all of the rivets came all the way  through to the
aluminium rub rail. To remove all of the rivets I had to  remove the
aluminium rail and I was unable to do that without destroying it  as any
bends that you put into the rail cannot be straightened. So plan  on
replacing the rub rail with a new one.

The sealant you decide to  use might determine how much you should do at one
time. I am not familiar  with the sealant Rummy uses but as it is intended
for roofs, I suspect it  stays very soft. Perhaps Rummy will advise what
happens to the sealant he  uses as it cures. But if you use a sealant that
hardens up when it cures  such as any of the marine sealants you will want 
to
close the gap with  rivets or bolts before the sealant cures. If you seal 
all
the way around  the boat and then start adding the rivets the sealant will
cure before you  will be able to compress the join. 

You will no doubt find that  everyone has strong and differing opinions 
about
what sealant to use and in  the end you will need to go with your best
judgement. Obviously you want a  top quality sealant that will last
indefinitely. You will also probably  want one that has excellent expansion
capabilities. As the deck and hull  expands and shrinks and also flexes, it
is important that the sealant has  the ability to tolerate that change. Even
sealant that has excellent  elasticity will not work if it is applied too
thin. Boat windows made of  Plexiglas and attached to the exterior without
hardware use a combination  of special thick double-sided tape and high flex
sealant - usually  Dow-Corning 795. The tape is extremely adhesive but also
maintains about a  1/8" gap between the window and the cabin side that 
allows
the sealant to  be thick enough to work properly. The 795 sealant is
extremely flexible but  also extremely adhesive. 

The main issue in the case of the hull deck  join, in my opinion, is not so
much adhesion, as the rivets will hold the  boat together, but rather to
maintain a good permanent and flexible seal.  You might consider using butyl
for this (the form that comes in a tube) but  because it would add nothing 
to
the strength of the join I would double up  on the rivets/bolts. 

One argument that might favour bolts over rivets  is that you can tighten 
the
bolts as needed while rivets apply maximum  pressure. If you want to make
sure that the sealant is not all squeezed out  of the join, bolts would give
you that degree of control. With butyl, that  should be less of a concern.
There is a lot (too much) of information on  the net about the pros and cons
of various sealants. I would be interested  to know which sealant Stan would
recommend.

Widen the gap with  wooden wedges/shims ahead of where you are injecting the
sealant to ensure  that the sealant is injected well into the gap. Put the
shims in first as  needed and then remove each as you reach that point with
the sealant. That  will allow you to get more sealant into the join and the
removal of the  shim will squeeze the sealant immediately while it is still
uncured.  

Another thing I would worry about is removing all of the rivets at  once. 
The
hull is very thin and very flexible at the top and I would worry  about the
whole thing changing shape one all of the rivets and sealant has  been
removed. Assuming that the boat is on its trailer when you do the job  and
knowing that the trailer applies uneven pressure to the hull, I would  not
want to find that the boat hull and deck became misaligned. That might  not
happen but at the same time you can avoid the risk by doing sections  of
about 8' at a time. Remove the rivets in one section only after the  
previous
section has been sealed and riveted/bolted. Alternatively, replace  some of
the rivets (say every 4') temporarily with bolts that can be easily  removed
as you work your way around the boat. 

I would definitely  add more rivets or bolts to those presently on the boat
especially around  the fore deck. I think that the waves on the bow work the
hull-deck join as  the hull is very flexible in comparison to the rigid deck
and that is where  the sealant can/will break. Certainly on my boat it was
only at the front  section that I had trouble with leaks. 

Finally, if you use rivets, I  would definitely use washers with them.

Good luck

Graham  


See the original archive post
×

Message to Webmaster:

To use your email application to send a messsage to the webmaster rather than this form, .



×

Post to the Rhodes 22 Email List:



×

Sending Post:

Your post is being sent... waiting