< prior
Back to Month
Go to Thread
2015-01-13; 22:01:20 EST
Member Since
2014-05-06
Posts: 3821
Bob: I look forward to seeing your posts. I never thought of using construction adhesive. I wonder to what extent the floor frame pieces are an essential part of the boat's structure or are they just a platform for the floor boards. If they are intended to give the hull rigidity, and I suspect they are, then I think I would go with the epoxy and glass. Does anyone know the answer to that question? GrahamSee the original archive post
-----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: January-13-15 8:57 PM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] installing new floor Sure thing Graham. I will post pics and keep everyone updated. I welcome lots of advice but am a brave (if not foolish) do it yourselfer. I once rebuild the stringers in a similar boat and bedded the pressure treated pine stringers in polyurethane construction adhesive. (Moisture cure stuff from home depot) I sailed the boat hard for years, had it fill up with water once for a month. When i sold it i got down in there to inspect and the job looked brand new and the adhesive was still perfectly holding the stringers to the hull. I would say epoxy would be a much better choice and a few layers of fiberglass cloth and resin even better. Bob > On Jan 13, 2015, at 8:37 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > Last summer I removed all of the stringers and end pieces for the > floor structure as I needed better access to the area over the keel. > The frames had been replaced by a previous owner who used pressure > treated fence boards. After more than 15 years the boards were still > perfectly sound. At one point I decided to add glass to bond the > boards to the hull better and was not sure if the epoxy would bond with the boards given the treatment. > The epoxy held firm - as I discovered when I removed them this summer. > > The problem with using fence boards is that they are only 1/2 inch > thick and that gives a very small edge area to drive the screws for > the floorboards, When I redo it I will either use pressure treated > deck boards that are 5/4 inch thick or white oak if I can get some at > a reasonable cost. I think using 2" material is a bit overkill but I > have no idea what was/is being used by General Boats. But based on my > experience, it appears that the pressure treated pine works fine. The > stuff they make today is much less toxic than what they were using > before, it is all under the floor boards and in my case will be coated > in epoxy so I don't think the toxic properties are something to worry about. > I will be interested to learn about how others are approaching the > installation of the framing. So please post what you do and how it > worked out. > > Graham > > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email List > Sent: January-13-15 8:13 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Centerboard cap > > I was thinking of using pressure treated pine > >>> On Jan 13, 2015, at 6:53 PM, The Rhodes 22 Email List >> <rhodes22-list at rhodes22.org> wrote: >> >> It would be great to see your plan and pics. >> >> It sounds like you're a step ahead of us. We're still sanding out the >> area where the stringers were and fitting the new ones. We're using >> 2x6 white oak >> >> Larry Allen >> Sarasota >> larrywallen at veizon.net >> 941-914-4065 >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >> 22 Email List >> Sent: Tuesday, January 13, 2015 2:45 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Centerboard cap >> >> Yes it is a 1983 rhodes and is in good shape except for the rotted >> floor. I will email you my plan and pics if you want. >> Also to Graham. Thanks for the input. I think i may as well tackle >> it > now. >> I also think i am going to remove the rub rail in the attempt to stop >> the rainwater that works in. >> Turning into a refit! >> >>>> On Jan 13, 2015, at 12:24 PM, The Rhodes 22 Email List >>> <rhodes22-list at rhodes22.org> wrote: >>> >>> We're doing exactly the same project. I'd like to talk with you or >>> get some information about how you're going to install the stringers >>> and what you're using. We also removed the centerboard cap to >>> inspect the board and the hull well. It's a 1986 R22 >>> >>> Larry Allen >>> Sarasota >>> "Makai" >>> larrywallen at verizon.net >>> 941-914-4065 >>> >>> >>> -----Original Message----- >>> From: rhodes22-list-bounces at rhodes22.org >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>> 22 Email List >>> Sent: Tuesday, January 13, 2015 11:45 AM >>> To: The Rhodes 22 Email List >>> Subject: [Rhodes22-list] Centerboard cap >>> >>> Ok, so i am getting ready to rebuild my floor. Its all clean and >>> ready to put the stringers in and i am looking at the centerboard >>> cap and wondering if i should take it apart and inspect it all. The >>> line looks good and it works. Some of the gelcoat is chipped off the cb. >>> Three of the cb cap screws are mild steel and rusty. >>> Advice? >>> >>> Bob (palatka fl) >>> "Saved by Grace" >>> The name comes from the fact that with each child i agreed to it if >>> i could buy a boat! Haha! So our fourth and last :-) was a >>> beautiful little girl named...Grace. >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >>> >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and >> archives go to http://www.rhodes22.org/list >> __________________________________________________ >> >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and >> archives go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 