The Rhodes 22 Discussion Group R22 Discussion Group

The Rhodes 22 Discussion Group


< prior

Back to Month

Go to Thread

Member Picture

The Rhodes 22 Email List



Soul of the sole

2015-01-16; 11:07:40 EST

Member Since

2014-05-06

Posts: 3821

   Graham,
   I've had a couple older boats and from what I have seen, the
   stringers, especially the two center most, are only to support the
   cabin floor. Mine didn't rest on the hull/bilge. They were tied into
   the bulkheads on the ends and only tabbed down to the bilge along
   their fore/aft length. The gaps between tabs allowed water to flow to
   the center of the bilge area. There was about ¼" between the bottom
   of the stringers and the bilge contour.
   The stringers were coated in epoxy. But from years of hull flexing and
   the movement between the floor and stringers, the epoxy was worn
   through on the tops of the stringers. When the bilge filled and
   overran, the stringer's open top edge allowed water to penetrate. If
   you decide to coat the stringers in epoxy, I'd suggest thickening the
   mix or laying a layer or two of glass on that top edge
   The two outer stringers (under the settee edge and under the gallery
   opening) are only about an inch or so tall. I've never removed these
   two but I assume, because of their height and because those side areas
   do hold water, that they are epoxied to the hull.
   Todd T.
   --
   Sent from my Android phone with [1]mail.com Mail. Please excuse my
   brevity.

   The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote:

     Graham,
     I don't think any quality boat builder has ever bonded a fiberglass
     hull to
     stringers with epoxy. Stringers are rigid, fiberglass hulls are
     flexible.
     Since epoxy cannot absorb flex, the hull would be prone to crack
     along the
     edges of the stringers bonded with epoxy.
     Another caveat on epoxy is using it to coat wood. Anything that
     keeps
     water out, keeps water in. If you coat stringers with epoxy, you
     will need
     to follow the same sealing protocol when drilling holes into
     epoxied
     stringers as you do with the wood cored deck. It would be more
     convenient
     to coat your new stringers with a bilge primer/sealer.
     Rick
     On Thu, Jan 15, 2015 at 1:39 PM, The Rhodes 22 Email List <
     rhodes22-list at rhodes22.org> wrote:
     > Bob:
     > I think any of your alternatives might work but when I install
     mine next
     > summer I intend to use epoxy with fibreglass tape for these
     reasons:
     > 1, I have done a lot of work with epoxy and am comfortable using
     it and I
     > have it along with the fillers on hand,
     > 2, wood adequately encapsulated in epoxy (3+ coats) should be
     impervious to
     > rot permitting the use of less expensive wood,
     > 3, bonded to the hull the stringers would add very significantly
     to the
     > rigidity of the hull, and
     > 4, the stringers will not flex and therefore will not come loose.
     >
     > I don't know how important point three is but given that the
     original
     > stringers were boned to the hull with cloth and polyester resin,
     I would
     > feel safer doing the same. Polyester is the other choice. It is
     much
     > cheaper
     > than epoxy but not a strong and not impervious to water vapour.
     >
     > Graham
     >
     >
See the original archive post
×

Message to Webmaster:

To use your email application to send a messsage to the webmaster rather than this form, .



×

Post to the Rhodes 22 Email List:



×

Sending Post:

Your post is being sent... waiting