< prior
Back to Month
Go to Thread
2015-01-16; 13:06:39 EST
Member Since
2014-05-06
Posts: 3821
Thanks Todd: I am glad to see this discussion arise. My stringers were glassed to the hull the full length with some cut outs to allow water to drain Also the port side seat front and the base of the cabinet on the starboard side were also glassed to the hull on the inside but without drains - which I found were needed as water did get in there. I am thinking that the central stringers are over the outer edge of the keel housing where there would be very little flex in the hull but further up would be a different matter. I have seen bats constructed with a series of hollow beams glasses to the hull that were intended to add rigidity. Similarly bulkheads reduce flex where they touch the hull. So this raises the question in my mind about when hull flexibility is a good thing and when is it not? Is Todd's construction typical - especially in older boats? I would appreciate any feedback. GrahamSee the original archive post
-----Original Message----- From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email List Sent: January-16-15 11:08 AM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] Soul of the sole Graham, I've had a couple older boats and from what I have seen, the stringers, especially the two center most, are only to support the cabin floor. Mine didn't rest on the hull/bilge. They were tied into the bulkheads on the ends and only tabbed down to the bilge along their fore/aft length. The gaps between tabs allowed water to flow to the center of the bilge area. There was about ¼" between the bottom of the stringers and the bilge contour. The stringers were coated in epoxy. But from years of hull flexing and the movement between the floor and stringers, the epoxy was worn through on the tops of the stringers. When the bilge filled and overran, the stringer's open top edge allowed water to penetrate. If you decide to coat the stringers in epoxy, I'd suggest thickening the mix or laying a layer or two of glass on that top edge The two outer stringers (under the settee edge and under the gallery opening) are only about an inch or so tall. I've never removed these two but I assume, because of their height and because those side areas do hold water, that they are epoxied to the hull. Todd T. -- Sent from my Android phone with [1]mail.com Mail. Please excuse my brevity. The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: Graham, I don't think any quality boat builder has ever bonded a fiberglass hull to stringers with epoxy. Stringers are rigid, fiberglass hulls are flexible. Since epoxy cannot absorb flex, the hull would be prone to crack along the edges of the stringers bonded with epoxy. Another caveat on epoxy is using it to coat wood. Anything that keeps water out, keeps water in. If you coat stringers with epoxy, you will need to follow the same sealing protocol when drilling holes into epoxied stringers as you do with the wood cored deck. It would be more convenient to coat your new stringers with a bilge primer/sealer. Rick On Thu, Jan 15, 2015 at 1:39 PM, The Rhodes 22 Email List < rhodes22-list at rhodes22.org> wrote: > Bob: > I think any of your alternatives might work but when I install mine next > summer I intend to use epoxy with fibreglass tape for these reasons: > 1, I have done a lot of work with epoxy and am comfortable using it and I > have it along with the fillers on hand, > 2, wood adequately encapsulated in epoxy (3+ coats) should be impervious to > rot permitting the use of less expensive wood, > 3, bonded to the hull the stringers would add very significantly to the > rigidity of the hull, and > 4, the stringers will not flex and therefore will not come loose. > > I don't know how important point three is but given that the original > stringers were boned to the hull with cloth and polyester resin, I would > feel safer doing the same. Polyester is the other choice. It is much > cheaper > than epoxy but not a strong and not impervious to water vapour. > > Graham > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: January-15-15 1:05 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Soul of the sole > > Ok let me stir the pot again. Should i bed my new stringers in 5200 or > epoxy them in or fiberglass tape and resin?? > Thoughts anyone? > Bob > > > On Jan 15, 2015, at 12:07 PM, The Rhodes 22 Email List > <rhodes22-list at rhodes22.org> wrote: > > > > 5200 is also permanent! Don't use it if you think you might ever want > > or need to remove it. > > > > Graham > > > > > > > > -----Original Message----- > > From: rhodes22-list-bounces at rhodes22.org > > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > > Email List > > Sent: January-15-15 10:04 AM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Soul of the sole > > > > Bob, > > > > 3M 5200 is an adhesive, not a sealant. A silicone sealant will give > > you better results. > > > > Rick > > > > On Thu, Jan 15, 2015 at 9:55 AM, The Rhodes 22 Email List < > > rhodes22-list at rhodes22.org> wrote: > > > >> Graham: Yes that is what i meant. These boats have a notoriously > >> leaky hull to deck joint. Stan explained it was due to the workers > >> ineptitude he had applying the joint caulk during those years. They > >> probably caulked the seam after the hull and deck were fastened > >> instead of caulking both sides then putting the sandwich together and > >> just > > wiping away the excess. > >> I am going to remove the rail, clean out as much old caulk as i can > >> and then seal it with 3m 5200 and re-attach the rub rail. It shouldnt > >> leak any more. I did this once before on an 80's era boat and it > >> worked > > great. > >> Shortcuts were happening in every industry back then. > >> > >>>> On Jan 15, 2015, at 9:43 AM, The Rhodes 22 Email List < > >>> rhodes22-list at rhodes22.org> wrote: > >>> > >>> I doubt that it is the rub rail that is leaking. If it is leaking > >>> through the screw holes you might get away with just removing the > >>> screws one at a time and reinserting with sealant. It is more likely > >>> that the leak is > >> behind > >>> the rub rail where the deck and hull join. > >>> > >>> Graham > >>> > >>> > >>> -----Original Message----- > >>> From: rhodes22-list-bounces at rhodes22.org > >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes > >>> 22 > >> Email > >>> List > >>> Sent: January-15-15 6:56 AM > >>> To: The Rhodes 22 Email List > >>> Subject: Re: [Rhodes22-list] Soul of the sole > >>> > >>> Thanks Rummy. > >>> Yes i already have the bleach and scrub brush out there. I am going > >>> to > >> do > >>> the rub rail first though. Very leaky boat! > >>> Bob > >>> > >>>>> On Jan 15, 2015, at 5:06 AM, The Rhodes 22 Email List > >>>> <rhodes22-list at rhodes22.org> wrote: > >>>> > >>>> I'm sure you are aware of this,but the photo shows a great deal of > > mold. > >>>> You might want to clean the area really good with a soapy bleach > >>>> solution prior to installing the new stringers. > >>>> > >>>> Rummy > >>>> > >>>> > >>>> In a message dated 1/14/2015 9:29:05 P.M. Eastern Standard Time, > >>>> rhodes22-list at rhodes22.org writes: > >>>> > >>>>[2] http://www.rhodes22.org/pipermail/rhodes22-list/attachments/2015011 > >>>> 4/6 > >>>> 474727 > >>>> 0/attachment.JPG > >>>> __________________________________________________ > >>>> To subscribe/unsubscribe go to > >>>>[3] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >>>> > >>>> For the list Charter and help with using the mailing list and > >>>> archives go to[4] http://www.rhodes22.org/list > >>>> __________________________________________________ > >>> > >>> __________________________________________________ > >>> To subscribe/unsubscribe go to > >>>[5] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >>> > >>> For the list Charter and help with using the mailing list and > >>> archives > >> go to > >>>[6] http://www.rhodes22.org/list > >>> __________________________________________________ > >>> > >>> __________________________________________________ > >>> To subscribe/unsubscribe go to > >>[7] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >>> > >>> For the list Charter and help with using the mailing list and > >>> archives > >> go to[8] http://www.rhodes22.org/list > >>> __________________________________________________ > >> > >> __________________________________________________ > >> To subscribe/unsubscribe go to > >>[9] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >> > >> For the list Charter and help with using the mailing list and > >> archives go to[10] http://www.rhodes22.org/list > >> __________________________________________________ > > __________________________________________________ > > To subscribe/unsubscribe go to > >[11] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to[12] http://www.rhodes22.org/list > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to > >[13] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to[14] http://www.rhodes22.org/list > > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to >[15] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to >[16] http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to >[17] http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to[18] http://www.rhodes22.org/list > __________________________________________________ > __________________________________________________ To subscribe/unsubscribe go to[19] http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to[20] http://www.rhodes22.org/list __________________________________________________ References 1. http://mail.com/ 2. http://www.rhodes22.org/pipermail/rhodes22-list/attachments/2015011 3. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 4. http://www.rhodes22.org/list 5. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 6. http://www.rhodes22.org/list 7. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 8. http://www.rhodes22.org/list 9. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 10. http://www.rhodes22.org/list 11. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 12. http://www.rhodes22.org/list 13. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 14. http://www.rhodes22.org/list 15. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 16. http://www.rhodes22.org/list 17. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 18. http://www.rhodes22.org/list 19. http://www.rhodes22.org/mailman/listinfo/rhodes22-list 20. http://www.rhodes22.org/list __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 