< prior
Back to Month
Go to Thread
2015-02-04; 18:00:55 EST
Member Since
2014-05-06
Posts: 3821
Graham: You present a good argument. Bob (palatka fl)See the original archive post
> On Feb 4, 2015, at 3:24 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > I would not suggest glassing the joint as a first option or on a newer boat. > It is a lot of work and unless you are stripping out the entire cabin > fixtures, too disruptive. However, if you have already removed all of the > interior structure and have good access to the joint it is not, in my view, > an unwarranted step to take. > > There is quite a lot of information on the net about the advantages of > glassing the join on boats where the join is such that glassing is > practicable. Some like the famous world sailor and author Hal Roth, did it > on the outside and then had to completely fair and repaint the entire boat. > That, I would not want to do on any boat where I had any concern about how > it would look afterwards. The construction of the Rhodes, however, makes > glassing on the inside much easier and practical as the join is entirely > hidden. > > Here is an example of advice on this point: > http://www.wavetrain.net/boats-a-gear/317-fiberglass-boatbuilding-hull-deck- > joints > > Because my boat was already stripped out, it took me a few hours to glass up > the join. It was not difficult and makes a join that is very strong - in > effect making the hull and deck into a single piece. I will still use bolts > so the glass only strengthens what would be there anyway. Weight is minimal > - maybe a few pounds. Increasing rigidity at the join is, in my view, a good > thing as movement at the join is bound to lead to trouble. > > My boat is an old one and there is no possibility that it will be recycled > or have the deck removed for any other purpose. But the old boats had > thinner glass construction and are more likely to leak - if only because of > their advanced age. The value will not depreciate as it has little value > anyway. What it should do, however, is give a boat that I like a lot a new > lease on life. > > All that said, you obviously need to carefully consider whether this is a > necessary or worthwhile repair under your particular circumstances. I don't > understand why it would be rejected out of hand in all circumstances. > > Graham > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: February-04-15 1:53 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] New Joint of Deck and Hull > > You can improve the joint and create a strong leakproof boat without > glassing it all together. If the job doesnt go well or the design flex isnt > there you could easily crack that fiberglass seal and then it would leak > like crazy. You also would remove the option of seperating the boat hull > and deck for rebuild or recycling. You also will reduce the value or worse > yet just be left with the value of hardware. Also you cannot stick on a > rubrail with resin... It will "rub" off. Too much work, too many risks. > Study what Rummy did. Its a perfect solution! > > Bob (palatka fl) > >>> On Feb 4, 2015, at 8:14 AM, The Rhodes 22 Email List >> <rhodes22-list at rhodes22.org> wrote: >> >> Personally, I think this is way overkill. You'll add a lot of weight >> to the boat pretty high up above the water line and it has to affect >> the sailing characteristics. I doubt you would find any manufacturer >> of boats today that joins the deck and hull like this so don't >> understand why you feel it is necessary. It is a very permanent >> solution, so think long and hard if you really want to make this > modification. >> >> Hank >> On Tue, Feb 3, 2015 at 6:00 PM, The Rhodes 22 Email List < >> rhodes22-list at rhodes22.org> wrote: >> >>> I have had a lot of great advise from everyone on the Deck and Hull >>> repair. But, still have one question/problem. >>> >>> Rhodes 22 have a Shoe Box joint and have aluminum pop rivets to hold >>> the joint together, plus some old style glue. I am following the >>> lead from Rummy and will Fiberglass the joint and use stainless steel >>> bolts with locking nuts. Here is my outline of the repair. >>> >>> On one side of boat at a time: >>> 1. Remove rivets one at a time and in every third hole insert a >>> temporary bolt and nut to hold joint together. . >>> 2. Remove all rub rail, aluminum and rubber. >>> 3. Sand the area where rub rail was, careful with temporary bolts. >>> 4. Insert permanent bolts with washers and locking nuts, use 5200 to >>> seal bolts. >>> 5. Tighten nuts from inside of boat. ( some may be hard to reach) 6. >>> Fiberglass the area , making sure to cover the bottom lip of the >>> joint and also cover the bolts. >>> 6b. Maybe gelcoat some area. >>> 7. Replace aluminum rub rail and use Fiberglass PEANUT BUTTER to >>> attach aluminum part to boat. ??? >>> 8. Insert rubber >>> 9. Touch up. >>> >>> The reason I want to use Fiberglass to set the rub rail is because >>> setting the rub rail with bolts will require more holes to be >>> drilled. My boat leaks from the holes where the aluminum pop rivets >>> have CORRODED. I am not in favor of drilling more holes into a boat. >>> I know that everyone says that it took 30 years for the leaks to >>> occur but why do the same mistake again? >>> >>> My question is : Will the rub rail hold using Fiberglass?? Other > Comments? >>> >>> Thanks, >>> Chuy >>> >>> My personal email is chcarreon at cox.net if you would rather reply just >>> to me. >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 