< prior
Back to Month
Go to Thread
2015-02-05; 16:15:49 EST
Member Since
2014-05-06
Posts: 3821
My 38 year old San Juan 21 hull/deck joint was glassed when built at the factory. I will admit it is light weight compared to Rhodes - 1,500 lbs (including the 400 lbs in swing keel). But that means more flex if anything. I've never heard of the joint being a problem. In fact it's touted as a no-problem area. FWIW Brooks Bridges Cambridge, MDSee the original archive post
On Wed, Feb 4, 2015 at 6:59 PM, Rhodes 22 mailing list [via Rhodes 22] < ml-node+s1065344n49440h57 at n5.nabble.com> wrote: > Glassing the hull-deck joint is contrary to common building practice, if > not ABYC standards. That joint needs to flex. > > Rick > > On Wed, Feb 4, 2015 at 6:00 PM, The Rhodes 22 Email List < > [hidden email] <http:///user/SendEmail.jtp?type=node&node=49440&i=0>> > wrote: > > > Graham: > > You present a good argument. > > > > Bob (palatka fl) > > > > > On Feb 4, 2015, at 3:24 PM, The Rhodes 22 Email List < > > [hidden email] <http:///user/SendEmail.jtp?type=node&node=49440&i=1>> > wrote: > > > > > > I would not suggest glassing the joint as a first option or on a newer > > boat. > > > It is a lot of work and unless you are stripping out the entire cabin > > > fixtures, too disruptive. However, if you have already removed all of > the > > > interior structure and have good access to the joint it is not, in my > > view, > > > an unwarranted step to take. > > > > > > There is quite a lot of information on the net about the advantages of > > > glassing the join on boats where the join is such that glassing is > > > practicable. Some like the famous world sailor and author Hal Roth, > did > > it > > > on the outside and then had to completely fair and repaint the entire > > boat. > > > That, I would not want to do on any boat where I had any concern about > > how > > > it would look afterwards. The construction of the Rhodes, however, > makes > > > glassing on the inside much easier and practical as the join is > entirely > > > hidden. > > > > > > Here is an example of advice on this point: > > > > > > http://www.wavetrain.net/boats-a-gear/317-fiberglass-boatbuilding-hull-deck- > > > joints > > > > > > Because my boat was already stripped out, it took me a few hours to > > glass up > > > the join. It was not difficult and makes a join that is very strong - > in > > > effect making the hull and deck into a single piece. I will still use > > bolts > > > so the glass only strengthens what would be there anyway. Weight is > > minimal > > > - maybe a few pounds. Increasing rigidity at the join is, in my view, > a > > good > > > thing as movement at the join is bound to lead to trouble. > > > > > > My boat is an old one and there is no possibility that it will be > > recycled > > > or have the deck removed for any other purpose. But the old boats had > > > thinner glass construction and are more likely to leak - if only > because > > of > > > their advanced age. The value will not depreciate as it has little > value > > > anyway. What it should do, however, is give a boat that I like a lot > a > > new > > > lease on life. > > > > > > All that said, you obviously need to carefully consider whether this > is a > > > necessary or worthwhile repair under your particular circumstances. I > > don't > > > understand why it would be rejected out of hand in all circumstances. > > > > > > Graham > > > > > > > > > -----Original Message----- > > > From: [hidden email] > <http:///user/SendEmail.jtp?type=node&node=49440&i=2> > > > [mailto:[hidden email] > <http:///user/SendEmail.jtp?type=node&node=49440&i=3>] On Behalf Of The > Rhodes 22 > > Email > > > List > > > Sent: February-04-15 1:53 PM > > > To: The Rhodes 22 Email List > > > Subject: Re: [Rhodes22-list] New Joint of Deck and Hull > > > > > > You can improve the joint and create a strong leakproof boat without > > > glassing it all together. If the job doesnt go well or the design > flex > > isnt > > > there you could easily crack that fiberglass seal and then it would > leak > > > like crazy. You also would remove the option of seperating the boat > hull > > > and deck for rebuild or recycling. You also will reduce the value or > > worse > > > yet just be left with the value of hardware. Also you cannot stick on > a > > > rubrail with resin... It will "rub" off. Too much work, too many > risks. > > > Study what Rummy did. Its a perfect solution! > > > > > > Bob (palatka fl) > > > > > >>> On Feb 4, 2015, at 8:14 AM, The Rhodes 22 Email List > > >> <[hidden email] <http:///user/SendEmail.jtp?type=node&node=49440&i=4>> > wrote: > > >> > > >> Personally, I think this is way overkill. You'll add a lot of weight > > >> to the boat pretty high up above the water line and it has to affect > > >> the sailing characteristics. I doubt you would find any manufacturer > > >> of boats today that joins the deck and hull like this so don't > > >> understand why you feel it is necessary. It is a very permanent > > >> solution, so think long and hard if you really want to make this > > > modification. > > >> > > >> Hank > > >> On Tue, Feb 3, 2015 at 6:00 PM, The Rhodes 22 Email List < > > >> [hidden email] <http:///user/SendEmail.jtp?type=node&node=49440&i=5>> > wrote: > > >> > > >>> I have had a lot of great advise from everyone on the Deck and Hull > > >>> repair. But, still have one question/problem. > > >>> > > >>> Rhodes 22 have a Shoe Box joint and have aluminum pop rivets to hold > > >>> the joint together, plus some old style glue. I am following the > > >>> lead from Rummy and will Fiberglass the joint and use stainless > steel > > >>> bolts with locking nuts. Here is my outline of the repair. > > >>> > > >>> On one side of boat at a time: > > >>> 1. Remove rivets one at a time and in every third hole insert a > > >>> temporary bolt and nut to hold joint together. . > > >>> 2. Remove all rub rail, aluminum and rubber. > > >>> 3. Sand the area where rub rail was, careful with temporary bolts. > > >>> 4. Insert permanent bolts with washers and locking nuts, use 5200 to > > >>> seal bolts. > > >>> 5. Tighten nuts from inside of boat. ( some may be hard to reach) 6. > > >>> Fiberglass the area , making sure to cover the bottom lip of the > > >>> joint and also cover the bolts. > > >>> 6b. Maybe gelcoat some area. > > >>> 7. Replace aluminum rub rail and use Fiberglass PEANUT BUTTER to > > >>> attach aluminum part to boat. ??? > > >>> 8. Insert rubber > > >>> 9. Touch up. > > >>> > > >>> The reason I want to use Fiberglass to set the rub rail is because > > >>> setting the rub rail with bolts will require more holes to be > > >>> drilled. My boat leaks from the holes where the aluminum pop rivets > > >>> have CORRODED. I am not in favor of drilling more holes into a > boat. > > >>> I know that everyone says that it took 30 years for the leaks to > > >>> occur but why do the same mistake again? > > >>> > > >>> My question is : Will the rub rail hold using Fiberglass?? Other > > > Comments? > > >>> > > >>> Thanks, > > >>> Chuy > > >>> > > >>> My personal email is [hidden email] > <http:///user/SendEmail.jtp?type=node&node=49440&i=6> if you would rather > reply just > > >>> to me. > > >>> __________________________________________________ > > >>> To subscribe/unsubscribe go to > > >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >>> > > >>> For the list Charter and help with using the mailing list and > > >>> archives go to http://www.rhodes22.org/list > > >>> __________________________________________________ > > >> __________________________________________________ > > >> To subscribe/unsubscribe go to > > >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >> > > >> For the list Charter and help with using the mailing list and > archives > > >> go to http://www.rhodes22.org/list > > >> __________________________________________________ > > > > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and archives > > go to > > > http://www.rhodes22.org/list > > > __________________________________________________ > > > > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > go > > to http://www.rhodes22.org/list > > __________________________________________________ > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ > > > ------------------------------ > If you reply to this email, your message will be added to the discussion > below: > http://rhodes-22.1065344.n5.nabble.com/Boat-Heaters-tp49416p49440.html > To unsubscribe from Boat Heaters, click here > <http://rhodes-22.1065344.n5.nabble.com/template/NamlServlet.jtp?macro=unsubscribe_by_code&node=49416&code=YnJpZGdlcy5icm9va3NAZ21haWwuY29tfDQ5NDE2fDExMTUxMDYxNTk=> > . > NAML > <http://rhodes-22.1065344.n5.nabble.com/template/NamlServlet.jtp?macro=macro_viewer&id=instant_html%21nabble%3Aemail.naml&base=nabble.naml.namespaces.BasicNamespace-nabble.view.web.template.NabbleNamespace-nabble.view.web.template.NodeNamespace&breadcrumbs=notify_subscribers%21nabble%3Aemail.naml-instant_emails%21nabble%3Aemail.naml-send_instant_email%21nabble%3Aemail.naml> > -- View this message in context: http://rhodes-22.1065344.n5.nabble.com/Boat-Heaters-tp49416p49442.html Sent from the Rhodes 22 mailing list archive at Nabble.com.
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 