< prior
Back to Month
Go to Thread
2015-04-01; 13:44:58 EDT
Member Since
2014-05-06
Posts: 3821
Graham: also i am going to add inspection ports in the galley cabinet floor and head floor as well. When i leave the boat at mooring or stored i will remove those so even more airflow occurs. A simple way to prolong the life of the woodwork. Bob (palatka)See the original archive post
> On Apr 1, 2015, at 1:12 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > Bob: > > When you say that you installed "extra" ballast I am wondering what was > there already and how much you added. I would like to add some myself but > don't know how much or where exactly to put it. > > The stringers under the settee and galley rotted out for me as well. Water > gets trapped there - especially under the galley where it is not visible and > rots out the wood. The source of water for me primarily was a leaking hull > deck join. I have glassed the joint so that should finally end the leaks but > I also put drain holes in the bottom of the stringers to ensure that any > water that makes its way in, and it will, can drain out on its own. Further, > I put an inspection hole in the bottom self of the galley so I can reach in > to the space should I want to check for water or retrieve anything the might > fall in behind the shelf. I am also encapsulating the settee and galley > stringers in multiple coats of epoxy. I am putting white Formica laminate on > the face of these pieces and all other wood surfaces to give a maintenance > free and easy to clean interior. > > With the floor stringers I am intending to use pressure treated deck boards. > A previous owner used pressure treated fence boards and while they stood up > very well to rot and held to epoxy very well, being only 1/2" thick did not > give a sufficient area to screw the deck boards to. Of course I will be > putting drain holes in them as well. > > Graham > > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: March-31-15 10:05 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Permission to come aboard? > > Mine is a 1983 and is in excellent condition for a boat of that age. (I > have had three 1983 sailboats and one 1982 sailboat) My deck is rock solid! > I can see under the front of my cockpit floor and it seems to have pine > boards set in the glass but not real sure. That floor is also rock solid. > > My floor rotted out most likely because it was stored with the hatch open. > There was one design "flaw" and it was that there were several areas that > trapped water. I am making sure all water can get to the bilge pump. I am > sure Stan probably puts in bilge scuppers in these stringers now. > I am rebuilding these with pressure treated wood/plywood. I dried it out > for several months so fiberglass will stick to it. I also have had good > luck with waterproof construction adhesive holding it in place until the > glass goes off. > Oh and my extra ballast is concrete glassed over just forward of the main > bulkhead. > I sealed this over with fiberglass cloth soaked in epoxy when i placed the > main bulkhead base. I didnt want the moisture in the concrete to keep the > wood wet. > > Bob (palatka) > >>> On Mar 31, 2015, at 8:35 PM, The Rhodes 22 Email List >> <rhodes22-list at rhodes22.org> wrote: >> >> Bob: >> Don't let me spook you. Any boat that old is bound to have some >> problems but just about anything can be fixed. The trick is to not let >> problems go too long - especially problems with the deck core. Some, >> if not all, of the problems I identified are probably unique to my >> boat. I don't know whether the contractors who built the older boats >> did the layup or just assembled the parts. Nor do I know how many >> contractors were used and what the differences might be between them. >> >> Many of the older boats have problems with the floor stringers rotting >> out - which is not a surprise given that the bilge is often wet and >> the stringers are wood. >> >> What is the ballast arrangement with your boat? In mine I have a stack >> of steel bars fiberglassed to the hull just forward of the forward > bulkhead. >> Some boats apparently have cement there. >> >> Graham >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email List >> Sent: March-31-15 6:55 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Permission to come aboard? >> >> What years were built where and by whom? >> >> Bob (palatka) >> >>>> On Mar 31, 2015, at 12:59 PM, The Rhodes 22 Email List >>> <rhodes22-list at rhodes22.org> wrote: >>> >>> Hi Graham - thanks for clarifying the porta-potti issue. And for the >>> invitation! >>> >>> I didn't realize 76's were built by 3rd parties. That's unsettling. I >>> will check out my keel, bearing in mind the problems you have had. >>> And the other flaws you detected. >>> >>> Much appreciated, >>> >>> Jefferson >>> >>> On 15-03-29 3:55 PM, "The Rhodes 22 Email List" >>> <rhodes22-list at rhodes22.org> wrote: >>> >>>> Jefferson: >>>> You can use a porta-pottie on Ontario waters so long as it is fixed >>>> in place and has a deck pump out. Most porta-potties have kits for >>>> this purpose. No need for a separate holding tank. >>>> >>>> You would be most welcome if you make the trip to my place and can >>>> tie up at my dock given that my boat is still on the hard. I also >>>> have a mooring that you can use. I am located just west of Lemoines >>>> Point on the north Shore of Lake Ontario. >>>> >>>> The Rhodes 22 were built under contract with 3rd parties in 1976 and >>>> as a result some of the construction details were lacking. A few >>>> things that you might want to check on the boat that might cause >>>> problems. >>>> >>>> - The transom rings were installed without nuts on the inside, >>>> - the deck leaked where the air vent for the holding tank went >>>> through the deck at the front - you may not have one if you don't >>>> have a holding tank but that is a prime spot for water to make its >>>> way into the core.. The softness that my deck developed when walked >>>> on was not due to rot as I suspected but was because the deck skin >>>> simply separated from the core, There was minimal sealant used to >>>> join the two surfaces and it simply let go. That is actually good >>>> news as it is possible to reattach the core by injecting epoxy under >>>> the skin rather than having to remove the deck and replace the core. >>>> I >> discovered this the hard way. >>>> - The keel on my boat split open at the bottom of the keel at the >>>> centreboard slot. I could only see it by laying flat on my back >>>> right under the keel - a position I rarely found myself in. The >>>> sharp corner seems to be the weakest point. Of course you might well >>>> not have that problem and I have no idea why it developed in mine, >>>> but by the time I realized that I had this problem it was probably >>>> years from the time it started and a crack had spread all the way >>>> around the centreboard opening. I only noticed the problem when I >>>> saw some of the internal filling hanging from the keel. I suspect >>>> that some water got into the keel and froze. I discovered that there >>>> were large voids in the keel where water could collect in >>>> substantial volume if it found its way in. It took 3 gallons of >>>> resin to fill the voids that I was able to find. My advice is to >>>> check it out before you launch. You probably will not have that >>>> problem but given that our boats were built so close together and >>>> potentially by the same builder it might be a reasonably prudent > examination to make. >>>> - The cap on my centreboard housing had been installed with a layer >>>> of fibreglass over it and the flange sealed with something like 3M >>>> 5200. I suspect that might have been a repair done by a subsequent >>>> owner but I can't be sure. It was a pain to remove the cap and >>>> impossible to do so without badly damaging it. >>>> - When I removed the bottom paint last summer I discovered that the >>>> gelcoat and even the substrate of the hull was damaged where the >>>> boat sat against the front struts of the trailer. Fortunately it >>>> isn't difficult to fix and the repair is ultimately covered by the >>>> bottom paint. I would look carefully in that area especially if you >>>> remove the existing paint. I repaired the glass by grinding out the >>>> damaged areas and replacing with multiple layers of cloth and epoxy. >>>> I plan to add some reinforcement to the inside of the hull this >>>> summer - particularly in that region as the fibreglass is thin there >>>> and dents badly on the trailer. Newer boats were built with thicker >>>> hulls to address that problem. >>>> >>>> Just because I had these problems does not mean that any of them >>>> will apply to you. But they did seem to me to be weak spots and you >>>> might be reassured to know they aren't a problem in your case. >>>> >>>> Take care, >>>> >>>> Graham Stewart >>>> >>>> -----Original Message----- >>>> From: rhodes22-list-bounces at rhodes22.org >>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>>> 22 Email List >>>> Sent: March-29-15 1:02 PM >>>> To: The Rhodes 22 Email List >>>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>>> >>>> Hi Graham, >>>> >>>> Thank you for the welcome. I'm gobsmacked there are only two Rhodes >>>> in the whole country. Throw a rock in any marina and you'll hit a >>>> Catalina 22 - a very inferior design to the Rhodes to my mind. >>>> >>>> My sympathies for your major restoration. I have neither the skills >>>> nor the patience and am praying that my hull is sound. But it is >>>> good to know someone out there knows. I went to Queen's U and know >>>> Bath well. Beautiful country, and great sailing around Kingston. I'd >>>> love to trailer my boat up there - going up the Richelieu from Lake >>>> Champlain and then up through the endless locks to Lake Ontario is >>>> something I have done once and don't need to do again! But I read >>>> somewhere that porta-potties are forbidden on Ontario lakes so I'd >>>> have to plumb in a head and holding tank or risk getting busted. >>>> >>>> I pulled the tarp off Patience this morning and sat in the cabin >>>> taking stock until my feet froze. Bring on Spring! >>>> >>>> Jefferson >>>> >>>> On 15-03-28 12:28 PM, "The Rhodes 22 Email List" >>>> <rhodes22-list at rhodes22.org> wrote: >>>> >>>>> Jefferson: >>>>> I am very excited to see that there may now be two Rhodes 22 boats >>>>> in Canada. Welcome. >>>>> >>>>> My boat, Agile, is hull number GBX220052G76 making mine a 1976 as well. >>>>> The >>>>> number on the sail is 244. Your boat was built in May and mine in >>>>> July of that year so they should be almost identical. I have been >>>>> doing a major restoration and in the process have dissected almost >>>>> every part of the boat so if you need to know more about what is >>>>> under the skin of the boat I should be able to tell you. I am >>>>> located on Lake Ontario at Kinston. >>>>> >>>>> Here is to great sailing. >>>>> >>>>> Graham >>>>> >>>>> >>>>> -----Original Message----- >>>>> From: rhodes22-list-bounces at rhodes22.org >>>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>>>> 22 Email List >>>>> Sent: March-28-15 10:21 AM >>>>> To: rhodes22-list at rhodes22.org >>>>> Subject: [Rhodes22-list] Permission to come aboard? >>>>> >>>>> >>>>> I am the new owner of a '76 Rhodes, hull number GBX220092E76. >>>>> Despite my admiration for the beauty and ingenuity of the boat's >>>>> design I would likely not have dared to make the jump if I hadn't >>>>> discovered this site and the generosity and patience of its >>>>> contributors. I feel honoured to join your ranks. >>>>> >>>>> About me: I grew up in a sailing family. Back in the dawn of time >>>>> when dinosaurs roamed the earth we sailed 14' Ackroyd dinghies, >>>>> then Rhodes Bantams, and on to Lightnings and Flying Dutchmen and >>>>> most recently Flying Scots. I discovered cruising when a good >>>>> friend bought a Catalina 25, and promptly came down with 2 >>>>> foot-itis - 25 became a Catalina 27, then a Columbia 31 and finally >>>>> a Mirage 26. We sailed on Lake >>>> Ontario, up the St. >>>>> Lawrence River past Quebec City, and all over Lake Champlain - >>>>> which is really an inland sea 100 miles long and up to 10 miles >>>>> wide in >> places. >>>>> >>>>> Then he sold the Mirage, and I thought well hell, now what am I >>>>> going to do? >>>>> After a lot of looking, I came across the Rhodes and fell in love. >>>>> >>>>> The boat: named "Patience," which feels quite appropriate consider >>>>> how long I looked for it. Among the papers inherited from the >>>>> previous owner is the yellowed but legible order sheet for the boat >>>>> in 1976, from GBC in Irvington-on-Hudson. With all the options the >>>>> original owner chose the bill for a brand spanking new Rhodes >>>>> Continental came to $8,095. The second owner bought the boat in >>>>> the early '80's andy sailed it on the Ottawa River, and then 22 >>>>> years ago, so he told me, they bought a cottage on a lake too small >>>>> for sailing and it has remained on its trailer under cover ever since. >>>>> I did a pretty thorough inspection with someone more experienced >>>>> than I, and it seems to be in pretty good shape. All original, >>>>> including cushion covers, the icebox, porta-potty and two burner >>>>> alcohol stove that was standard on RC models in '76. It is >>>>> equipped with a 150 genoa. The work it needs seems to be mostly >>>>> cosmetic, aside from running rigging which needs to be updated, and >>>>> if it doesn't sink to the bottom on launch day I'll be delighted. >>>>> >>>>> I'm going to moor it on Lake Memphremagog this summer while I work >>>>> on it, and then on Lake Champlain. I plan to send 10% of the price >>>>> I paid to Stan, which isn't going to thrill him since I didn't pay >>>>> much, and in Canadian dollars, but seems the right thing to do >>>>> anyway. I'm not sure what I'll be able to afford to buy from >>>>> General Boats, given the current exchange rates and my own budget. >>>>> But it will be my first stop when I go shopping. >>>>> >>>>> So that's me and Patience, slowly emerging from the melting snow. I >>>>> have about six million questions but will try not to test your >>>>> patience. I can't download any attachments with "Old Nabble" in the >>>>> address, and if anyone could enlighten me I will continue to scour >>>>> the archives for answers. >>>>> >>>>> Jefferson Lewis >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> __________________________________________________ >>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>> >>>>> For the list Charter and help with using the mailing list and >>>>> archives go to http://www.rhodes22.org/list >>>>> __________________________________________________ >>>> >>>> >>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and >>>> archives go to http://www.rhodes22.org/list >>>> __________________________________________________ >>> >>> >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 