< prior
Back to Month
Go to Thread
2015-04-01; 15:05:20 EDT
Member Since
2014-05-06
Posts: 3821
I have a true 1974 and it has concrete ballast. Starts under the water tank and forward bunk and stops just before the keel well. During my rebuild I had to replace the stringers, framing and decking. I also cut in stringer scupper style drains so the bilge water does not pool up and stay trapped. In Arizona humidity and condensation are not a issue but I also put hinges on my cabin sole plate so I can lift them up to inspect, clean and air out the bilge on occasion. Fred Haag Mesa, Az Fred Sent via the Samsung Galaxy S® 5 ACTIVE™, an AT&T 4G LTE smartphoneSee the original archive post
-------- Original message -------- From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> Date:04/01/2015 11:11 AM (GMT-07:00) To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> Subject: Re: [Rhodes22-list] Ballast I have read on the list that extra ballast performs well just forward of the mast and by the water tank. I plan to do that with a battery bank. Bob (palatka) > On Apr 1, 2015, at 2:05 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > Sometime in 1976 the internal ballast changed from Steel bricks to cement. I > don't know what is used today. Steel is obviously much denser than cement so > I expect that the actual ballast weight is greater with steel than with the > cement unless the volume of the cement is considerably larger. > > My neighbour has given up on the construction of a 55' steel cutter after > working on it for 40 years - on and off. As a result he has tons (literally) > of lead bricks and I can buy some for Agile. I had thought about placing > some on either side of the centreboard housing and forward along with the > steel bricks that are there already. > > Does anyone have any thoughts about how one might determine where and how > much ballast might be added? At this point I am thinking that I will place > some bricks loose in the bilge and play with the distribution until it feels > right - but that could constitute a lot of fiddling. All that time spent > sailing detracts substantially from the time I have available to work on the > repair of the boat. > > Graham > > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email > List > Sent: April-01-15 1:32 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Permission to come aboard? > > Graham: > Ok. I didnt add the extra ballast. It had it already. I called it "extra" > since i consider needing to add internal ballast a design flaw or a building > shortcut (i.e. Concrete instead of lead). But hey i am not criticizing the > boat, just explaining my word choice. > > Yes i too am adding LIMBER HOLES too. At 4 am i woke up remembering that i > called them "stringer scuppers" yesterday which isnt nautically correct! > Hahaha! > > For the main center floor stringers i cut them from 2x6" pressure treated > lumber. The wider area will make adding the floor and bilge inspection > hatch easier and acually was cheaper than 5/4" deck wood. > > I am still deciding what to do about my hull/deck joint. Access is good > from inside at this point. I found these great caulk gun tubes of two part > epoxy that mix as you pump it that i should be able to use to easily fill > the joint. We will see! The other option is the Np-1 Rummy recommended. > > I think that there is also a fair amount of water that finds its way into > the bilge from condensation. I am designing a solar powered bilge dryer. > Another "we will see" > > Another idea is that i am adding floor vents to keep air moving under the > floor boards and to allow the bilge to dry. > > Bob (palatka) > >>> On Apr 1, 2015, at 1:12 PM, The Rhodes 22 Email List >> <rhodes22-list at rhodes22.org> wrote: >> >> Bob: >> >> When you say that you installed "extra" ballast I am wondering what >> was there already and how much you added. I would like to add some >> myself but don't know how much or where exactly to put it. >> >> The stringers under the settee and galley rotted out for me as well. >> Water gets trapped there - especially under the galley where it is not >> visible and rots out the wood. The source of water for me primarily >> was a leaking hull deck join. I have glassed the joint so that should >> finally end the leaks but I also put drain holes in the bottom of the >> stringers to ensure that any water that makes its way in, and it will, >> can drain out on its own. Further, I put an inspection hole in the >> bottom self of the galley so I can reach in to the space should I want >> to check for water or retrieve anything the might fall in behind the >> shelf. I am also encapsulating the settee and galley stringers in >> multiple coats of epoxy. I am putting white Formica laminate on the >> face of these pieces and all other wood surfaces to give a maintenance > free and easy to clean interior. >> >> With the floor stringers I am intending to use pressure treated deck > boards. >> A previous owner used pressure treated fence boards and while they >> stood up very well to rot and held to epoxy very well, being only 1/2" >> thick did not give a sufficient area to screw the deck boards to. Of >> course I will be putting drain holes in them as well. >> >> Graham >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email List >> Sent: March-31-15 10:05 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Permission to come aboard? >> >> Mine is a 1983 and is in excellent condition for a boat of that age. >> (I have had three 1983 sailboats and one 1982 sailboat) My deck is rock > solid! >> I can see under the front of my cockpit floor and it seems to have >> pine boards set in the glass but not real sure. That floor is also rock > solid. >> >> My floor rotted out most likely because it was stored with the hatch open. >> There was one design "flaw" and it was that there were several areas >> that trapped water. I am making sure all water can get to the bilge >> pump. I am sure Stan probably puts in bilge scuppers in these stringers > now. >> I am rebuilding these with pressure treated wood/plywood. I dried it >> out for several months so fiberglass will stick to it. I also have >> had good luck with waterproof construction adhesive holding it in >> place until the glass goes off. >> Oh and my extra ballast is concrete glassed over just forward of the >> main bulkhead. >> I sealed this over with fiberglass cloth soaked in epoxy when i placed >> the main bulkhead base. I didnt want the moisture in the concrete to >> keep the wood wet. >> >> Bob (palatka) >> >>>> On Mar 31, 2015, at 8:35 PM, The Rhodes 22 Email List >>> <rhodes22-list at rhodes22.org> wrote: >>> >>> Bob: >>> Don't let me spook you. Any boat that old is bound to have some >>> problems but just about anything can be fixed. The trick is to not >>> let problems go too long - especially problems with the deck core. >>> Some, if not all, of the problems I identified are probably unique to >>> my boat. I don't know whether the contractors who built the older >>> boats did the layup or just assembled the parts. Nor do I know how >>> many contractors were used and what the differences might be between > them. >>> >>> Many of the older boats have problems with the floor stringers >>> rotting out - which is not a surprise given that the bilge is often >>> wet and the stringers are wood. >>> >>> What is the ballast arrangement with your boat? In mine I have a >>> stack of steel bars fiberglassed to the hull just forward of the >>> forward >> bulkhead. >>> Some boats apparently have cement there. >>> >>> Graham >>> >>> >>> >>> -----Original Message----- >>> From: rhodes22-list-bounces at rhodes22.org >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>> 22 Email List >>> Sent: March-31-15 6:55 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>> >>> What years were built where and by whom? >>> >>> Bob (palatka) >>> >>>>> On Mar 31, 2015, at 12:59 PM, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> wrote: >>>> >>>> Hi Graham - thanks for clarifying the porta-potti issue. And for the >>>> invitation! >>>> >>>> I didn't realize 76's were built by 3rd parties. That's unsettling. >>>> I will check out my keel, bearing in mind the problems you have had. >>>> And the other flaws you detected. >>>> >>>> Much appreciated, >>>> >>>> Jefferson >>>> >>>> On 15-03-29 3:55 PM, "The Rhodes 22 Email List" >>>> <rhodes22-list at rhodes22.org> wrote: >>>> >>>>> Jefferson: >>>>> You can use a porta-pottie on Ontario waters so long as it is fixed >>>>> in place and has a deck pump out. Most porta-potties have kits for >>>>> this purpose. No need for a separate holding tank. >>>>> >>>>> You would be most welcome if you make the trip to my place and can >>>>> tie up at my dock given that my boat is still on the hard. I also >>>>> have a mooring that you can use. I am located just west of Lemoines >>>>> Point on the north Shore of Lake Ontario. >>>>> >>>>> The Rhodes 22 were built under contract with 3rd parties in 1976 >>>>> and as a result some of the construction details were lacking. A >>>>> few things that you might want to check on the boat that might >>>>> cause problems. >>>>> >>>>> - The transom rings were installed without nuts on the inside, >>>>> - the deck leaked where the air vent for the holding tank went >>>>> through the deck at the front - you may not have one if you don't >>>>> have a holding tank but that is a prime spot for water to make its >>>>> way into the core.. The softness that my deck developed when walked >>>>> on was not due to rot as I suspected but was because the deck skin >>>>> simply separated from the core, There was minimal sealant used to >>>>> join the two surfaces and it simply let go. That is actually good >>>>> news as it is possible to reattach the core by injecting epoxy >>>>> under the skin rather than having to remove the deck and replace the > core. >>>>> I >>> discovered this the hard way. >>>>> - The keel on my boat split open at the bottom of the keel at the >>>>> centreboard slot. I could only see it by laying flat on my back >>>>> right under the keel - a position I rarely found myself in. The >>>>> sharp corner seems to be the weakest point. Of course you might >>>>> well not have that problem and I have no idea why it developed in >>>>> mine, but by the time I realized that I had this problem it was >>>>> probably years from the time it started and a crack had spread all >>>>> the way around the centreboard opening. I only noticed the problem >>>>> when I saw some of the internal filling hanging from the keel. I >>>>> suspect that some water got into the keel and froze. I discovered >>>>> that there were large voids in the keel where water could collect >>>>> in substantial volume if it found its way in. It took 3 gallons of >>>>> resin to fill the voids that I was able to find. My advice is to >>>>> check it out before you launch. You probably will not have that >>>>> problem but given that our boats were built so close together and >>>>> potentially by the same builder it might be a reasonably prudent >> examination to make. >>>>> - The cap on my centreboard housing had been installed with a layer >>>>> of fibreglass over it and the flange sealed with something like 3M >>>>> 5200. I suspect that might have been a repair done by a subsequent >>>>> owner but I can't be sure. It was a pain to remove the cap and >>>>> impossible to do so without badly damaging it. >>>>> - When I removed the bottom paint last summer I discovered that the >>>>> gelcoat and even the substrate of the hull was damaged where the >>>>> boat sat against the front struts of the trailer. Fortunately it >>>>> isn't difficult to fix and the repair is ultimately covered by the >>>>> bottom paint. I would look carefully in that area especially if you >>>>> remove the existing paint. I repaired the glass by grinding out the >>>>> damaged areas and replacing with multiple layers of cloth and epoxy. >>>>> I plan to add some reinforcement to the inside of the hull this >>>>> summer - particularly in that region as the fibreglass is thin >>>>> there and dents badly on the trailer. Newer boats were built with >>>>> thicker hulls to address that problem. >>>>> >>>>> Just because I had these problems does not mean that any of them >>>>> will apply to you. But they did seem to me to be weak spots and you >>>>> might be reassured to know they aren't a problem in your case. >>>>> >>>>> Take care, >>>>> >>>>> Graham Stewart >>>>> >>>>> -----Original Message----- >>>>> From: rhodes22-list-bounces at rhodes22.org >>>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>>>> 22 Email List >>>>> Sent: March-29-15 1:02 PM >>>>> To: The Rhodes 22 Email List >>>>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>>>> >>>>> Hi Graham, >>>>> >>>>> Thank you for the welcome. I'm gobsmacked there are only two Rhodes >>>>> in the whole country. Throw a rock in any marina and you'll hit a >>>>> Catalina 22 - a very inferior design to the Rhodes to my mind. >>>>> >>>>> My sympathies for your major restoration. I have neither the >>>>> skills nor the patience and am praying that my hull is sound. But >>>>> it is good to know someone out there knows. I went to Queen's U and >>>>> know Bath well. Beautiful country, and great sailing around >>>>> Kingston. I'd love to trailer my boat up there - going up the >>>>> Richelieu from Lake Champlain and then up through the endless locks >>>>> to Lake Ontario is something I have done once and don't need to do >>>>> again! But I read somewhere that porta-potties are forbidden on >>>>> Ontario lakes so I'd have to plumb in a head and holding tank or risk > getting busted. >>>>> >>>>> I pulled the tarp off Patience this morning and sat in the cabin >>>>> taking stock until my feet froze. Bring on Spring! >>>>> >>>>> Jefferson >>>>> >>>>> On 15-03-28 12:28 PM, "The Rhodes 22 Email List" >>>>> <rhodes22-list at rhodes22.org> wrote: >>>>> >>>>>> Jefferson: >>>>>> I am very excited to see that there may now be two Rhodes 22 boats >>>>>> in Canada. Welcome. >>>>>> >>>>>> My boat, Agile, is hull number GBX220052G76 making mine a 1976 as > well. >>>>>> The >>>>>> number on the sail is 244. Your boat was built in May and mine in >>>>>> July of that year so they should be almost identical. I have been >>>>>> doing a major restoration and in the process have dissected almost >>>>>> every part of the boat so if you need to know more about what is >>>>>> under the skin of the boat I should be able to tell you. I am >>>>>> located on Lake Ontario at Kinston. >>>>>> >>>>>> Here is to great sailing. >>>>>> >>>>>> Graham >>>>>> >>>>>> >>>>>> -----Original Message----- >>>>>> From: rhodes22-list-bounces at rhodes22.org >>>>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The >>>>>> Rhodes >>>>>> 22 Email List >>>>>> Sent: March-28-15 10:21 AM >>>>>> To: rhodes22-list at rhodes22.org >>>>>> Subject: [Rhodes22-list] Permission to come aboard? >>>>>> >>>>>> >>>>>> I am the new owner of a '76 Rhodes, hull number GBX220092E76. >>>>>> Despite my admiration for the beauty and ingenuity of the boat's >>>>>> design I would likely not have dared to make the jump if I hadn't >>>>>> discovered this site and the generosity and patience of its >>>>>> contributors. I feel honoured to join your ranks. >>>>>> >>>>>> About me: I grew up in a sailing family. Back in the dawn of time >>>>>> when dinosaurs roamed the earth we sailed 14' Ackroyd dinghies, >>>>>> then Rhodes Bantams, and on to Lightnings and Flying Dutchmen and >>>>>> most recently Flying Scots. I discovered cruising when a good >>>>>> friend bought a Catalina 25, and promptly came down with 2 >>>>>> foot-itis - 25 became a Catalina 27, then a Columbia 31 and >>>>>> finally a Mirage 26. We sailed on Lake >>>>> Ontario, up the St. >>>>>> Lawrence River past Quebec City, and all over Lake Champlain - >>>>>> which is really an inland sea 100 miles long and up to 10 miles >>>>>> wide in >>> places. >>>>>> >>>>>> Then he sold the Mirage, and I thought well hell, now what am I >>>>>> going to do? >>>>>> After a lot of looking, I came across the Rhodes and fell in love. >>>>>> >>>>>> The boat: named "Patience," which feels quite appropriate consider >>>>>> how long I looked for it. Among the papers inherited from the >>>>>> previous owner is the yellowed but legible order sheet for the >>>>>> boat in 1976, from GBC in Irvington-on-Hudson. With all the >>>>>> options the original owner chose the bill for a brand spanking new >>>>>> Rhodes Continental came to $8,095. The second owner bought the >>>>>> boat in the early '80's andy sailed it on the Ottawa River, and >>>>>> then 22 years ago, so he told me, they bought a cottage on a lake >>>>>> too small for sailing and it has remained on its trailer under cover > ever since. >>>>>> I did a pretty thorough inspection with someone more experienced >>>>>> than I, and it seems to be in pretty good shape. All original, >>>>>> including cushion covers, the icebox, porta-potty and two burner >>>>>> alcohol stove that was standard on RC models in '76. It is >>>>>> equipped with a 150 genoa. The work it needs seems to be mostly >>>>>> cosmetic, aside from running rigging which needs to be updated, >>>>>> and if it doesn't sink to the bottom on launch day I'll be delighted. >>>>>> >>>>>> I'm going to moor it on Lake Memphremagog this summer while I work >>>>>> on it, and then on Lake Champlain. I plan to send 10% of the price >>>>>> I paid to Stan, which isn't going to thrill him since I didn't pay >>>>>> much, and in Canadian dollars, but seems the right thing to do >>>>>> anyway. I'm not sure what I'll be able to afford to buy from >>>>>> General Boats, given the current exchange rates and my own budget. >>>>>> But it will be my first stop when I go shopping. >>>>>> >>>>>> So that's me and Patience, slowly emerging from the melting snow. >>>>>> I have about six million questions but will try not to test your >>>>>> patience. I can't download any attachments with "Old Nabble" in >>>>>> the address, and if anyone could enlighten me I will continue to >>>>>> scour the archives for answers. >>>>>> >>>>>> Jefferson Lewis >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> __________________________________________________ >>>>>> To subscribe/unsubscribe go to >>>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>> >>>>>> For the list Charter and help with using the mailing list and >>>>>> archives go to http://www.rhodes22.org/list >>>>>> __________________________________________________ >>>>> >>>>> >>>>> >>>>> __________________________________________________ >>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>> >>>>> For the list Charter and help with using the mailing list and >>>>> archives go to http://www.rhodes22.org/list >>>>> __________________________________________________ >>>> >>>> >>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and >>>> archives go to http://www.rhodes22.org/list >>>> __________________________________________________ >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >>> archives go to http://www.rhodes22.org/list >>> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >> __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________ __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 