< prior
Back to Month
Go to Thread
2015-04-02; 10:48:53 EDT
Member Since
2014-05-06
Posts: 3821
How many Rhodies have added ballast? If so where and how much? Bob (palatka)See the original archive post
> On Apr 1, 2015, at 8:49 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote: > > I have a 1996 R22 (recycled 2012). Last spring I placed seven 26 lb. lead > bricks (2" x 4"x 8") alongside and forward of the centerboard trunk. I > cannot really gauge the effect since there are so many variables affecting > how a sailboat responds to steadily increasing windspeeds or to a gust. If > I add any more ballast I would, per Stan, place it father forward, on the > centerline just aft of the vee berth bulkhead and as low as possible. > Richard Arking R22 on Sheepshead Bay, Brooklyn NY > > On Wed, Apr 1, 2015 at 5:10 PM, The Rhodes 22 Email List < > rhodes22-list at rhodes22.org> wrote: > >> The boat is right beside me here in Ontario near Kingston. Want a beautiful >> 55' steel cutter hull? >> >> Graham >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: April-01-15 3:36 PM >> To: rhodes22-list at rhodes22.org >> Subject: Re: [Rhodes22-list] Ballast >> >> >> Graham, >> >> Lead will soon be the new gold. >> Not really... but it IS getting harder to find with the latest EPA >> regulations. Where is your friend's boat? >> >> Todd T. >> >> >> Sent: Wednesday, April 01, 2015 at 2:05 PM >> From: "The Rhodes 22 Email List" <rhodes22-list at rhodes22.org> >> To: "'The Rhodes 22 Email List'" <rhodes22-list at rhodes22.org> >> Subject: [Rhodes22-list] Ballast >> Sometime in 1976 the internal ballast changed from Steel bricks to >> cement. I >> don't know what is used today. Steel is obviously much denser than >> cement so >> I expect that the actual ballast weight is greater with steel than >> with the >> cement unless the volume of the cement is considerably larger. >> My neighbour has given up on the construction of a 55' steel cutter >> after >> working on it for 40 years - on and off. As a result he has tons >> (literally) >> of lead bricks and I can buy some for Agile. I had thought about >> placing >> some on either side of the centreboard housing and forward along with >> the >> steel bricks that are there already. >> Does anyone have any thoughts about how one might determine where and >> how >> much ballast might be added? At this point I am thinking that I will >> place >> some bricks loose in the bilge and play with the distribution until it >> feels >> right - but that could constitute a lot of fiddling. All that time >> spent >> sailing detracts substantially from the time I have available to work >> on the >> repair of the boat. >> Graham >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: April-01-15 1:32 PM >> To: The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Permission to come aboard? >> Graham: >> Ok. I didnt add the extra ballast. It had it already. I called it >> "extra" >> since i consider needing to add internal ballast a design flaw or a >> building >> shortcut (i.e. Concrete instead of lead). But hey i am not criticizing >> the >> boat, just explaining my word choice. >> Yes i too am adding LIMBER HOLES too. At 4 am i woke up remembering >> that i >> called them "stringer scuppers" yesterday which isnt nautically >> correct! >> Hahaha! >> For the main center floor stringers i cut them from 2x6" pressure >> treated >> lumber. The wider area will make adding the floor and bilge inspection >> hatch easier and acually was cheaper than 5/4" deck wood. >> I am still deciding what to do about my hull/deck joint. Access is >> good >> from inside at this point. I found these great caulk gun tubes of two >> part >> epoxy that mix as you pump it that i should be able to use to easily >> fill >> the joint. We will see! The other option is the Np-1 Rummy >> recommended. >> I think that there is also a fair amount of water that finds its way >> into >> the bilge from condensation. I am designing a solar powered bilge >> dryer. >> Another "we will see" >> Another idea is that i am adding floor vents to keep air moving under >> the >> floor boards and to allow the bilge to dry. >> Bob (palatka) >>>> On Apr 1, 2015, at 1:12 PM, The Rhodes 22 Email List >>> <rhodes22-list at rhodes22.org> wrote: >>> >>> Bob: >>> >>> When you say that you installed "extra" ballast I am wondering what >>> was there already and how much you added. I would like to add some >>> myself but don't know how much or where exactly to put it. >>> >>> The stringers under the settee and galley rotted out for me as well. >>> Water gets trapped there - especially under the galley where it is >> not >>> visible and rots out the wood. The source of water for me primarily >>> was a leaking hull deck join. I have glassed the joint so that >> should >>> finally end the leaks but I also put drain holes in the bottom of >> the >>> stringers to ensure that any water that makes its way in, and it >> will, >>> can drain out on its own. Further, I put an inspection hole in the >>> bottom self of the galley so I can reach in to the space should I >> want >>> to check for water or retrieve anything the might fall in behind the >>> shelf. I am also encapsulating the settee and galley stringers in >>> multiple coats of epoxy. I am putting white Formica laminate on the >>> face of these pieces and all other wood surfaces to give a >> maintenance >> free and easy to clean interior. >>> >>> With the floor stringers I am intending to use pressure treated deck >> boards. >>> A previous owner used pressure treated fence boards and while they >>> stood up very well to rot and held to epoxy very well, being only >> 1/2" >>> thick did not give a sufficient area to screw the deck boards to. Of >>> course I will be putting drain holes in them as well. >>> >>> Graham >>> >>> >>> >>> -----Original Message----- >>> From: rhodes22-list-bounces at rhodes22.org >>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >> 22 >>> Email List >>> Sent: March-31-15 10:05 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>> >>> Mine is a 1983 and is in excellent condition for a boat of that age. >>> (I have had three 1983 sailboats and one 1982 sailboat) My deck is >> rock >> solid! >>> I can see under the front of my cockpit floor and it seems to have >>> pine boards set in the glass but not real sure. That floor is also >> rock >> solid. >>> >>> My floor rotted out most likely because it was stored with the hatch >> open. >>> There was one design "flaw" and it was that there were several areas >>> that trapped water. I am making sure all water can get to the bilge >>> pump. I am sure Stan probably puts in bilge scuppers in these >> stringers >> now. >>> I am rebuilding these with pressure treated wood/plywood. I dried it >>> out for several months so fiberglass will stick to it. I also have >>> had good luck with waterproof construction adhesive holding it in >>> place until the glass goes off. >>> Oh and my extra ballast is concrete glassed over just forward of the >>> main bulkhead. >>> I sealed this over with fiberglass cloth soaked in epoxy when i >> placed >>> the main bulkhead base. I didnt want the moisture in the concrete to >>> keep the wood wet. >>> >>> Bob (palatka) >>> >>>>> On Mar 31, 2015, at 8:35 PM, The Rhodes 22 Email List >>>> <rhodes22-list at rhodes22.org> wrote: >>>> >>>> Bob: >>>> Don't let me spook you. Any boat that old is bound to have some >>>> problems but just about anything can be fixed. The trick is to not >>>> let problems go too long - especially problems with the deck core. >>>> Some, if not all, of the problems I identified are probably unique >> to >>>> my boat. I don't know whether the contractors who built the older >>>> boats did the layup or just assembled the parts. Nor do I know how >>>> many contractors were used and what the differences might be >> between >> them. >>>> >>>> Many of the older boats have problems with the floor stringers >>>> rotting out - which is not a surprise given that the bilge is often >>>> wet and the stringers are wood. >>>> >>>> What is the ballast arrangement with your boat? In mine I have a >>>> stack of steel bars fiberglassed to the hull just forward of the >>>> forward >>> bulkhead. >>>> Some boats apparently have cement there. >>>> >>>> Graham >>>> >>>> >>>> >>>> -----Original Message----- >>>> From: rhodes22-list-bounces at rhodes22.org >>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes >>>> 22 Email List >>>> Sent: March-31-15 6:55 PM >>>> To: The Rhodes 22 Email List >>>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>>> >>>> What years were built where and by whom? >>>> >>>> Bob (palatka) >>>> >>>>>> On Mar 31, 2015, at 12:59 PM, The Rhodes 22 Email List >>>>> <rhodes22-list at rhodes22.org> wrote: >>>>> >>>>> Hi Graham - thanks for clarifying the porta-potti issue. And for >> the >>>>> invitation! >>>>> >>>>> I didn't realize 76's were built by 3rd parties. That's >> unsettling. >>>>> I will check out my keel, bearing in mind the problems you have >> had. >>>>> And the other flaws you detected. >>>>> >>>>> Much appreciated, >>>>> >>>>> Jefferson >>>>> >>>>> On 15-03-29 3:55 PM, "The Rhodes 22 Email List" >>>>> <rhodes22-list at rhodes22.org> wrote: >>>>> >>>>>> Jefferson: >>>>>> You can use a porta-pottie on Ontario waters so long as it is >> fixed >>>>>> in place and has a deck pump out. Most porta-potties have kits >> for >>>>>> this purpose. No need for a separate holding tank. >>>>>> >>>>>> You would be most welcome if you make the trip to my place and >> can >>>>>> tie up at my dock given that my boat is still on the hard. I also >>>>>> have a mooring that you can use. I am located just west of >> Lemoines >>>>>> Point on the north Shore of Lake Ontario. >>>>>> >>>>>> The Rhodes 22 were built under contract with 3rd parties in 1976 >>>>>> and as a result some of the construction details were lacking. A >>>>>> few things that you might want to check on the boat that might >>>>>> cause problems. >>>>>> >>>>>> - The transom rings were installed without nuts on the inside, >>>>>> - the deck leaked where the air vent for the holding tank went >>>>>> through the deck at the front - you may not have one if you don't >>>>>> have a holding tank but that is a prime spot for water to make >> its >>>>>> way into the core.. The softness that my deck developed when >> walked >>>>>> on was not due to rot as I suspected but was because the deck >> skin >>>>>> simply separated from the core, There was minimal sealant used to >>>>>> join the two surfaces and it simply let go. That is actually good >>>>>> news as it is possible to reattach the core by injecting epoxy >>>>>> under the skin rather than having to remove the deck and replace >> the >> core. >>>>>> I >>>> discovered this the hard way. >>>>>> - The keel on my boat split open at the bottom of the keel at the >>>>>> centreboard slot. I could only see it by laying flat on my back >>>>>> right under the keel - a position I rarely found myself in. The >>>>>> sharp corner seems to be the weakest point. Of course you might >>>>>> well not have that problem and I have no idea why it developed in >>>>>> mine, but by the time I realized that I had this problem it was >>>>>> probably years from the time it started and a crack had spread >> all >>>>>> the way around the centreboard opening. I only noticed the >> problem >>>>>> when I saw some of the internal filling hanging from the keel. I >>>>>> suspect that some water got into the keel and froze. I discovered >>>>>> that there were large voids in the keel where water could collect >>>>>> in substantial volume if it found its way in. It took 3 gallons >> of >>>>>> resin to fill the voids that I was able to find. My advice is to >>>>>> check it out before you launch. You probably will not have that >>>>>> problem but given that our boats were built so close together and >>>>>> potentially by the same builder it might be a reasonably prudent >>> examination to make. >>>>>> - The cap on my centreboard housing had been installed with a >> layer >>>>>> of fibreglass over it and the flange sealed with something like >> 3M >>>>>> 5200. I suspect that might have been a repair done by a >> subsequent >>>>>> owner but I can't be sure. It was a pain to remove the cap and >>>>>> impossible to do so without badly damaging it. >>>>>> - When I removed the bottom paint last summer I discovered that >> the >>>>>> gelcoat and even the substrate of the hull was damaged where the >>>>>> boat sat against the front struts of the trailer. Fortunately it >>>>>> isn't difficult to fix and the repair is ultimately covered by >> the >>>>>> bottom paint. I would look carefully in that area especially if >> you >>>>>> remove the existing paint. I repaired the glass by grinding out >> the >>>>>> damaged areas and replacing with multiple layers of cloth and >> epoxy. >>>>>> I plan to add some reinforcement to the inside of the hull this >>>>>> summer - particularly in that region as the fibreglass is thin >>>>>> there and dents badly on the trailer. Newer boats were built with >>>>>> thicker hulls to address that problem. >>>>>> >>>>>> Just because I had these problems does not mean that any of them >>>>>> will apply to you. But they did seem to me to be weak spots and >> you >>>>>> might be reassured to know they aren't a problem in your case. >>>>>> >>>>>> Take care, >>>>>> >>>>>> Graham Stewart >>>>>> >>>>>> -----Original Message----- >>>>>> From: rhodes22-list-bounces at rhodes22.org >>>>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The >> Rhodes >>>>>> 22 Email List >>>>>> Sent: March-29-15 1:02 PM >>>>>> To: The Rhodes 22 Email List >>>>>> Subject: Re: [Rhodes22-list] Permission to come aboard? >>>>>> >>>>>> Hi Graham, >>>>>> >>>>>> Thank you for the welcome. I'm gobsmacked there are only two >> Rhodes >>>>>> in the whole country. Throw a rock in any marina and you'll hit a >>>>>> Catalina 22 - a very inferior design to the Rhodes to my mind. >>>>>> >>>>>> My sympathies for your major restoration. I have neither the >>>>>> skills nor the patience and am praying that my hull is sound. But >>>>>> it is good to know someone out there knows. I went to Queen's U >> and >>>>>> know Bath well. Beautiful country, and great sailing around >>>>>> Kingston. I'd love to trailer my boat up there - going up the >>>>>> Richelieu from Lake Champlain and then up through the endless >> locks >>>>>> to Lake Ontario is something I have done once and don't need to >> do >>>>>> again! But I read somewhere that porta-potties are forbidden on >>>>>> Ontario lakes so I'd have to plumb in a head and holding tank or >> risk >> getting busted. >>>>>> >>>>>> I pulled the tarp off Patience this morning and sat in the cabin >>>>>> taking stock until my feet froze. Bring on Spring! >>>>>> >>>>>> Jefferson >>>>>> >>>>>> On 15-03-28 12:28 PM, "The Rhodes 22 Email List" >>>>>> <rhodes22-list at rhodes22.org> wrote: >>>>>> >>>>>>> Jefferson: >>>>>>> I am very excited to see that there may now be two Rhodes 22 >> boats >>>>>>> in Canada. Welcome. >>>>>>> >>>>>>> My boat, Agile, is hull number GBX220052G76 making mine a 1976 >> as >> well. >>>>>>> The >>>>>>> number on the sail is 244. Your boat was built in May and mine >> in >>>>>>> July of that year so they should be almost identical. I have >> been >>>>>>> doing a major restoration and in the process have dissected >> almost >>>>>>> every part of the boat so if you need to know more about what is >>>>>>> under the skin of the boat I should be able to tell you. I am >>>>>>> located on Lake Ontario at Kinston. >>>>>>> >>>>>>> Here is to great sailing. >>>>>>> >>>>>>> Graham >>>>>>> >>>>>>> >>>>>>> -----Original Message----- >>>>>>> From: rhodes22-list-bounces at rhodes22.org >>>>>>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The >>>>>>> Rhodes >>>>>>> 22 Email List >>>>>>> Sent: March-28-15 10:21 AM >>>>>>> To: rhodes22-list at rhodes22.org >>>>>>> Subject: [Rhodes22-list] Permission to come aboard? >>>>>>> >>>>>>> >>>>>>> I am the new owner of a '76 Rhodes, hull number GBX220092E76. >>>>>>> Despite my admiration for the beauty and ingenuity of the boat's >>>>>>> design I would likely not have dared to make the jump if I >> hadn't >>>>>>> discovered this site and the generosity and patience of its >>>>>>> contributors. I feel honoured to join your ranks. >>>>>>> >>>>>>> About me: I grew up in a sailing family. Back in the dawn of >> time >>>>>>> when dinosaurs roamed the earth we sailed 14' Ackroyd dinghies, >>>>>>> then Rhodes Bantams, and on to Lightnings and Flying Dutchmen >> and >>>>>>> most recently Flying Scots. I discovered cruising when a good >>>>>>> friend bought a Catalina 25, and promptly came down with 2 >>>>>>> foot-itis - 25 became a Catalina 27, then a Columbia 31 and >>>>>>> finally a Mirage 26. We sailed on Lake >>>>>> Ontario, up the St. >>>>>>> Lawrence River past Quebec City, and all over Lake Champlain - >>>>>>> which is really an inland sea 100 miles long and up to 10 miles >>>>>>> wide in >>>> places. >>>>>>> >>>>>>> Then he sold the Mirage, and I thought well hell, now what am I >>>>>>> going to do? >>>>>>> After a lot of looking, I came across the Rhodes and fell in >> love. >>>>>>> >>>>>>> The boat: named "Patience," which feels quite appropriate >> consider >>>>>>> how long I looked for it. Among the papers inherited from the >>>>>>> previous owner is the yellowed but legible order sheet for the >>>>>>> boat in 1976, from GBC in Irvington-on-Hudson. With all the >>>>>>> options the original owner chose the bill for a brand spanking >> new >>>>>>> Rhodes Continental came to $8,095. The second owner bought the >>>>>>> boat in the early '80's andy sailed it on the Ottawa River, and >>>>>>> then 22 years ago, so he told me, they bought a cottage on a >> lake >>>>>>> too small for sailing and it has remained on its trailer under >> cover >> ever since. >>>>>>> I did a pretty thorough inspection with someone more experienced >>>>>>> than I, and it seems to be in pretty good shape. All original, >>>>>>> including cushion covers, the icebox, porta-potty and two burner >>>>>>> alcohol stove that was standard on RC models in '76. It is >>>>>>> equipped with a 150 genoa. The work it needs seems to be mostly >>>>>>> cosmetic, aside from running rigging which needs to be updated, >>>>>>> and if it doesn't sink to the bottom on launch day I'll be >> delighted. >>>>>>> >>>>>>> I'm going to moor it on Lake Memphremagog this summer while I >> work >>>>>>> on it, and then on Lake Champlain. I plan to send 10% of the >> price >>>>>>> I paid to Stan, which isn't going to thrill him since I didn't >> pay >>>>>>> much, and in Canadian dollars, but seems the right thing to do >>>>>>> anyway. I'm not sure what I'll be able to afford to buy from >>>>>>> General Boats, given the current exchange rates and my own >> budget. >>>>>>> But it will be my first stop when I go shopping. >>>>>>> >>>>>>> So that's me and Patience, slowly emerging from the melting >> snow. >>>>>>> I have about six million questions but will try not to test your >>>>>>> patience. I can't download any attachments with "Old Nabble" in >>>>>>> the address, and if anyone could enlighten me I will continue to >>>>>>> scour the archives for answers. >>>>>>> >>>>>>> Jefferson Lewis >>>>>>> >>>>>>> >>>>>>> >>>>>>> >>>>>>> >>>>>>> >>>>>>> __________________________________________________ >>>>>>> To subscribe/unsubscribe go to >>>>>>> [1]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>>> >>>>>>> For the list Charter and help with using the mailing list and >>>>>>> archives go to [2]http://www.rhodes22.org/list >>>>>>> __________________________________________________ >>>>>> >>>>>> >>>>>> >>>>>> __________________________________________________ >>>>>> To subscribe/unsubscribe go to >>>>>> [3]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>> >>>>>> For the list Charter and help with using the mailing list and >>>>>> archives go to [4]http://www.rhodes22.org/list >>>>>> __________________________________________________ >>>>> >>>>> >>>>> >>>>> __________________________________________________ >>>>> To subscribe/unsubscribe go to >>>>> [5]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>> >>>>> For the list Charter and help with using the mailing list and >>>>> archives go to [6]http://www.rhodes22.org/list >>>>> __________________________________________________ >>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> [7]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and >>>> archives go to [8]http://www.rhodes22.org/list >>>> __________________________________________________ >>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> [9]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and >>>> archives go to [10]http://www.rhodes22.org/list >>>> __________________________________________________ >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> [11]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >> archives >>> go to [12]http://www.rhodes22.org/list >>> __________________________________________________ >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> [13]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and >> archives >>> go to [14]http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> [15]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> For the list Charter and help with using the mailing list and archives >> go to >> [16]http://www.rhodes22.org/list >> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> [17]http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> For the list Charter and help with using the mailing list and archives >> go to [18]http://www.rhodes22.org/list >> __________________________________________________ >> >> References >> >> 1. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 2. http://www.rhodes22.org/list >> 3. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 4. http://www.rhodes22.org/list >> 5. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 6. http://www.rhodes22.org/list >> 7. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 8. http://www.rhodes22.org/list >> 9. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 10. http://www.rhodes22.org/list >> 11. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 12. http://www.rhodes22.org/list >> 13. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 14. http://www.rhodes22.org/list >> 15. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 16. http://www.rhodes22.org/list >> 17. http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> 18. http://www.rhodes22.org/list >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives go >> to >> http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives go >> to http://www.rhodes22.org/list >> __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 