< prior
Back to Month
Go to Thread
2015-06-03; 01:12:37 EDT
Member Since
2014-05-06
Posts: 3821
Great info for the list Graham. This is a project I will need to do before I leave the states.See the original archive post
On Tue, Jun 2, 2015 at 8:51 AM, The Rhodes 22 Email List < rhodes22-list at rhodes22.org> wrote: > Nice write up Graham but I must be missing a sentence or an email or > something. > > If you are going to have Lexan windows, why paint them? I read the > part about "to make sure that the grey tape and white sides of the > cabin did not show through" but if you are painting the whole window > why use Lexan at all? Or can you still see out through the paint? do > the windows let light in? > > I'm confused. > > Mary Lou > 1991 R22 Fretless > (recycled 1998) > still on the hard > but just about ready > to splash for the season > in Rock Hall, MD > > > > At 11:16 AM 6/2/2015, you wrote: > >For those who are interested in replacing cabin ports with acrylic > >panels, I thought I would bring you up to date on my highly > >scientific experiments using the method of attaching windows without > >using any hardware. > > > >My experiments were intended to demonstrate for me the strength of a > >joint using Dow Corning silicone # 795 and 3M brand tape VHB 4991 > >and the paint I intended to use to coat the inside of the acrylic panel. > > > >First, I joined some pieces of Lexan I had using the tape and the > >sealant and let it sit for 48 hours for the sealant to cure. At 48 > >hours the sealant is about 90% cured but it continues to cure for 72 > >hours. I couldn't wait that long. I attached a small piece of lexan > >(about 1.5" x 3") to a larger piece at a corner. I messed up the > >sealant with the result that I got some on top of the tape - which > >seems like a distinct possibility when I do the large panels so I > >was curious to see what effect that had. By leaving the smaller > >piece extending beyond the larger piece I had a tab that I could use > >to peal the pieces apart. I have attached a picture of what I call > >the "flex test". > > > >By holding the main piece down and lifting up on the tab I was able > >to bend the panels far beyond any curvature on the cabin side of the > >boat without any sign of the joint letting g. Also. the joint had > >enough flex that the panels could move past each other slightly to > >allow for a nice even bend. When I bent the joint to the maximum the > >lexan broke (see photo) before any sign that the joint was > >weakening. Lexan is very flexible and strong so that seemed to me to > >be a good sign although I should note that the Lexan was only 3/16" > >thick. I figure that if I can't break the join even on small pieces > >without destroying the Lexan, that has to be a very strong and flexible > joint. > > > >As an aside, the sealant has a useful life of one year. When I > >ordered mine it was already 8 months old and expired in March 2015. > >I called 3M last fall to see if there was any way to extend the life > >of the material. The technical support person told me to seal it up > >in plastic and put it in my freezer - which I did. He then told me > >to test it before using it by laying out a bead and letting it sit > >for 3 hours. If it skinned over, it was good but if it stayed wet it > >will never cure - even though it looks fine coming out of the tube. > >I Had thought that old material would harden in the tube so that was > >potentially very useful to know. I have read online where others > >complained that this sealant never cured and I expect they were > >using material that was too old. In my case it appears the freezing > >worked as the sealant cured up nicely. > > > >Although the acrylic panels I am using are dark tinted, I wanted to > >make sure that the grey tape and white sides of the cabin did not > >show through so I needed to find a suitable paint to coat the > >inside. I wanted something that would adhere tenaciously to acrylic > >so that in turn the tape and sealant would adhere to the paint. I > >also wanted something that would apply by spray to give a perfectly > >even coat and preferably was fast drying. Articles I read advised > >using engine exhaust paint. The particular types suggested were not > >available locally and a ridiculous price to order by mail across the > >Canada/US border. Also I noticed that application instructions for > >similar paints available locally specified that it dries easily but > >does not cure until it is brought up to a high heat. That , of > >course , is not going to happen with acrylic so I was left wondering > >how it would work in an uncured state. > > > >I experimented with a number of paints - especially paints that are > >intended for plastic. The first time I did this in 1995 I used some > >sort of enamel that subsequently pealed of even though it was > >between the Lexan and the cabin side. It was thick, soft and had > >poor adhesion with Lexan. So I wanted something better than that. I > >noticed that the paints I was testing went on thick and took a long > >time to dry. They also scratched off too easily for my liking. I > >then tried some barbeque paint that I had. The paint is intended for > >high heat applications but had a maximum temperature of 600 degrees > >- which is much lower than the exhaust paint but still much higher > >than anything the boat will ever face before I am jumping overboard > >and it does not require heat to cure. It also sprays on beautifully > >in thin coats, dries to touch in a few minutes - no dust problems - > >and can be recoated several time within an hour. That meant that I > >could apply multiple thin and even coats. It give! > > s a satin finish rather than high gloss which I thought might make > > a better surface for the tape to adhere to. I first painted pieces > > of Lexan and clear acrylic and let it sit for about 3 months to see > > if there was any indication of incompatibility between the paint > > and the plastic. There was no sign of incompatibility that I could see. > > > >I tested the adhesion of the paint by trying to scratch it off soon > >after application and after several months and by applying a variety > >of tapes - duct tape and packing tape, house wrap tape etc, - and > >then peal it back both while the paint was fresh and after the tape > >had been in place for several months. As the flex test shows I also > >tried adhesion with the double-sided tape and, as noted, the lexan > >broke before the seal showed any sign of letting go. I also applied > >sealant, let it cure , and tried to remove it by pealing it back. > >The "paint test" is shown in an attached picture. It shows packing > >tape that had been left in place for several months. The tape was > >firmly attached but came off cleanly leaving the paint firmly > >attached to the Lexan. Scratching the paint with a sharp object left > >a scratch, of course, but did not remove any of the surrounding > >paint. So I think this is a good paint for this application. > > > >To prepare the windows, I cut the acrylic panels from a 1/8" plywood > >template, routed a slight bevel on the outside edges, laid out where > >the opening in the cabin were, made a template for consistent > >openings made out of Formica (which works well because it is thin > >and hard) and then cut the protective paper around what will be the > >openings using the template and exacto knife. I then removed all the > >protective covering except where the openings will be and painted > >the pieces with four thin coats of barbeque paint. I have attached a > >photo of the painted pieces. > > > >After the acrylic is attached to the boat I will remove the masking > >tape on the outside of the acrylic panes, the tape on the cabin > >sides and remove the protective paper from the outside of the panels > >and the inside of the open part. I tested whether I would be able > >to peel off the inside sections once it had been painted over > >especially given that it will be difficult to raise an edge once the > >panels are installed. I found that if I apply a strip of packing > >tape to the covering paper leaving the end folded over so I can grab > >it, when I peal it back the tape holds sufficiently to raise the > >protective paper cleanly avoiding the need to scratch up an edge. > >Hopefully that works in the real life situation. I would hate to > >have acrylic panels permanently attached with paper coving the > >opening that I can't remove. > > > >So I have chosen all the materials and tested them as best I can for > >suitability. I have also worked out a temporary clamping system to > >hold the panels in place while the tape and sealant cure. That might > >be unnecessary but given the curve of the cabin I don't want to take > >a chance on that part. I have masked the boat around the edge of the > >acrylic and sanded the paint on the cabin side so that is flat , > >smooth but dulled (220 grit). Now all that is left is to attach the > >actual panels and frankly that is what worries me most. While online > >instructions suggest applying the tape and sealant to the panel and > >then apply the panel to the boat, my thinking is that because the > >cabin side is a compound curve I would be better to apply the tape > >and sealant to the cabin and then press the panel into place. > > > >Time matters. I don't have forever to apply the sealant and remove > >the tape cover before pressing the panel on and worse still, I only > >get one chance to get the panel in the exact location. There is > >really no room for error. I have "rehearsed" placing the panel with > >my wife but that was without any of the tape or sealant. The cabin > >side has a moulded in edge at both the bottom and the aft end that > >are very helpful guides but one still need to make sure from the > >moment of first touch that everything is aligned perfectly so that > >the rest will wrap into place exactly where it is supposed to be. My > >hope is that I can rest the bottom edge and aft corner against the > >little raised edge first and then wrap the piece up into place at the top. > > > >If anyone has any clever ideas about how I could make the process > >idiot proof I would be forever grateful. The idea of having to use > >a chisel and grinder to remove the misaligned panels has no appeal > >to me at this juncture. I think I will need a very good shot of > >Rummy's Mont Gay medicine to calm my nerves first. > > > > > >Graham > >-------------- next part -------------- > >A non-text attachment was scrubbed... > >Name: Barbeque paint.jpg > >Type: image/jpeg > >Size: 178369 bytes > >Desc: not available > >Url : > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/916312ae/attachment.jpg > > > >-------------- next part -------------- > >A non-text attachment was scrubbed... > >Name: Window flex test.jpg > >Type: image/jpeg > >Size: 52391 bytes > >Desc: not available > >Url : > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/916312ae/attachment-0001.jpg > > > >-------------- next part -------------- > >A non-text attachment was scrubbed... > >Name: Window paint test.jpg > >Type: image/jpeg > >Size: 82200 bytes > >Desc: not available > >Url : > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/916312ae/attachment-0002.jpg > > > >-------------- next part -------------- > >A non-text attachment was scrubbed... > >Name: Windows painted.jpg > >Type: image/jpeg > >Size: 54671 bytes > >Desc: not available > >Url : > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/916312ae/attachment-0003.jpg > > > >__________________________________________________ > >To subscribe/unsubscribe go to > >http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > >For the list Charter and help with using the mailing list and > >archives go to http://www.rhodes22.org/list > >__________________________________________________ > > > > > >----- > >No virus found in this message. > >Checked by AVG - www.avg.com > >Version: 2015.0.5961 / Virus Database: 4355/9924 - Release Date: 06/02/15 > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 