< prior
Back to Month
Go to Thread
2015-06-03; 13:50:03 EDT
Member Since
2014-05-06
Posts: 3821
Ah-ha! thanks for the explanation. I knew I was missing something! thanks! Mary Lou R22 Fretless Rock Hall, MD At 12:31 PM 6/3/2015, you wrote:See the original archive post
>Mary Lou: > >I will paint the inside of the acrylic panel everywhere except where the >openings will be. I intend to do this by removing the protective paper >everywhere except the port opening, then paint the panel and finally remove >the paper over the opening once the panel is installed. In the picture I >provided with the panels painted the paper covering is still over the port >area so it looks solid. You can't see the paper covering in the picture. I >could remove the paper before I install the panel but it seems sensible to >leave that area protected from scratches and any sealant that might get >smeared on it during installation. > >I have attached a picture showing the plywood template, for the panel, the >Formica template (white) for the opening and the two acrylic panels with the >protective paper still on and the opening areas marked. > >The acrylic panel is deep tinted so perhaps nothing will show through but >the tinting is not opaque and I suspect that in sunlight the grey tape and >white cabin will show. I don't have a spare piece of the tinted acrylic to >test this as I had the dealer cut the original panel for me using a plywood >template that I provided. I should have asked for some scrap piece. I did >have some clear acrylic that I used to test painting and the cutting and >removal of the paper. I have attached a picture of the clear acrylic, >partially painted and with the opening protective paper pealed back on both >sides. That might make what I am describing a litter easier to follow. > >I have attached a picture of the boat with the lexan windows that I attached >back in 1995. The picture was taken 20 years later when the paint had pealed >and you can see the cabin and peeling paint under through the Lexan. Hence >my obsession with using the right paint. > >For more about my paint selection I have attached a picture of panels of >Lexan coated with various paints along with observational comments. I think >it demonstrates fairly well why the barbeque paint seemed superior for this >task. > >I hope that helps. > >Graham > > >-----Original Message----- >From: rhodes22-list-bounces at rhodes22.org >[mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email >List >Sent: June-02-15 11:51 AM >To: The Rhodes 22 Email List >Subject: Re: [Rhodes22-list] Window replacement update > >Nice write up Graham but I must be missing a sentence or an email or >something. > >If you are going to have Lexan windows, why paint them? I read the part >about "to make sure that the grey tape and white sides of the cabin did not >show through" but if you are painting the whole window why use Lexan at all? >Or can you still see out through the paint? do the windows let light in? > >I'm confused. > >Mary Lou >1991 R22 Fretless >(recycled 1998) >still on the hard >but just about ready >to splash for the season >in Rock Hall, MD > > > >At 11:16 AM 6/2/2015, you wrote: > >For those who are interested in replacing cabin ports with acrylic > >panels, I thought I would bring you up to date on my highly scientific > >experiments using the method of attaching windows without using any > >hardware. > > > >My experiments were intended to demonstrate for me the strength of a > >joint using Dow Corning silicone # 795 and 3M brand tape VHB 4991 and > >the paint I intended to use to coat the inside of the acrylic panel. > > > >First, I joined some pieces of Lexan I had using the tape and the > >sealant and let it sit for 48 hours for the sealant to cure. At 48 > >hours the sealant is about 90% cured but it continues to cure for 72 > >hours. I couldn't wait that long. I attached a small piece of lexan > >(about 1.5" x 3") to a larger piece at a corner. I messed up the > >sealant with the result that I got some on top of the tape - which > >seems like a distinct possibility when I do the large panels so I was > >curious to see what effect that had. By leaving the smaller piece > >extending beyond the larger piece I had a tab that I could use to peal > >the pieces apart. I have attached a picture of what I call the "flex > >test". > > > >By holding the main piece down and lifting up on the tab I was able to > >bend the panels far beyond any curvature on the cabin side of the boat > >without any sign of the joint letting g. Also. the joint had enough > >flex that the panels could move past each other slightly to allow for a > >nice even bend. When I bent the joint to the maximum the lexan broke > >(see photo) before any sign that the joint was weakening. Lexan is very > >flexible and strong so that seemed to me to be a good sign although I > >should note that the Lexan was only 3/16" > >thick. I figure that if I can't break the join even on small pieces > >without destroying the Lexan, that has to be a very strong and flexible >joint. > > > >As an aside, the sealant has a useful life of one year. When I ordered > >mine it was already 8 months old and expired in March 2015. > >I called 3M last fall to see if there was any way to extend the life of > >the material. The technical support person told me to seal it up in > >plastic and put it in my freezer - which I did. He then told me to test > >it before using it by laying out a bead and letting it sit for 3 hours. > >If it skinned over, it was good but if it stayed wet it will never cure > >- even though it looks fine coming out of the tube. > >I Had thought that old material would harden in the tube so that was > >potentially very useful to know. I have read online where others > >complained that this sealant never cured and I expect they were using > >material that was too old. In my case it appears the freezing worked as > >the sealant cured up nicely. > > > >Although the acrylic panels I am using are dark tinted, I wanted to > >make sure that the grey tape and white sides of the cabin did not show > >through so I needed to find a suitable paint to coat the inside. I > >wanted something that would adhere tenaciously to acrylic so that in > >turn the tape and sealant would adhere to the paint. I also wanted > >something that would apply by spray to give a perfectly even coat and > >preferably was fast drying. Articles I read advised using engine > >exhaust paint. The particular types suggested were not available > >locally and a ridiculous price to order by mail across the Canada/US > >border. Also I noticed that application instructions for similar paints > >available locally specified that it dries easily but does not cure > >until it is brought up to a high heat. That , of course , is not going > >to happen with acrylic so I was left wondering how it would work in an > >uncured state. > > > >I experimented with a number of paints - especially paints that are > >intended for plastic. The first time I did this in 1995 I used some > >sort of enamel that subsequently pealed of even though it was between > >the Lexan and the cabin side. It was thick, soft and had poor adhesion > >with Lexan. So I wanted something better than that. I noticed that the > >paints I was testing went on thick and took a long time to dry. They > >also scratched off too easily for my liking. I then tried some barbeque > >paint that I had. The paint is intended for high heat applications but > >had a maximum temperature of 600 degrees > >- which is much lower than the exhaust paint but still much higher than > >anything the boat will ever face before I am jumping overboard and it > >does not require heat to cure. It also sprays on beautifully in thin > >coats, dries to touch in a few minutes - no dust problems - and can be > >recoated several time within an hour. That meant that I could apply > >multiple thin and even coats. It give! > > s a satin finish rather than high gloss which I thought might make a > >better surface for the tape to adhere to. I first painted pieces of > >Lexan and clear acrylic and let it sit for about 3 months to see if > >there was any indication of incompatibility between the paint and the > >plastic. There was no sign of incompatibility that I could see. > > > >I tested the adhesion of the paint by trying to scratch it off soon > >after application and after several months and by applying a variety of > >tapes - duct tape and packing tape, house wrap tape etc, - and then > >peal it back both while the paint was fresh and after the tape had been > >in place for several months. As the flex test shows I also tried > >adhesion with the double-sided tape and, as noted, the lexan broke > >before the seal showed any sign of letting go. I also applied sealant, > >let it cure , and tried to remove it by pealing it back. > >The "paint test" is shown in an attached picture. It shows packing tape > >that had been left in place for several months. The tape was firmly > >attached but came off cleanly leaving the paint firmly attached to the > >Lexan. Scratching the paint with a sharp object left a scratch, of > >course, but did not remove any of the surrounding paint. So I think > >this is a good paint for this application. > > > >To prepare the windows, I cut the acrylic panels from a 1/8" plywood > >template, routed a slight bevel on the outside edges, laid out where > >the opening in the cabin were, made a template for consistent openings > >made out of Formica (which works well because it is thin and hard) and > >then cut the protective paper around what will be the openings using > >the template and exacto knife. I then removed all the protective > >covering except where the openings will be and painted the pieces with > >four thin coats of barbeque paint. I have attached a photo of the > >painted pieces. > > > >After the acrylic is attached to the boat I will remove the masking > >tape on the outside of the acrylic panes, the tape on the cabin sides > >and remove the protective paper from the outside of the panels and the > >inside of the open part. I tested whether I would be able to peel off > >the inside sections once it had been painted over especially given that > >it will be difficult to raise an edge once the panels are installed. I > >found that if I apply a strip of packing tape to the covering paper > >leaving the end folded over so I can grab it, when I peal it back the > >tape holds sufficiently to raise the protective paper cleanly avoiding > >the need to scratch up an edge. > >Hopefully that works in the real life situation. I would hate to have > >acrylic panels permanently attached with paper coving the opening that > >I can't remove. > > > >So I have chosen all the materials and tested them as best I can for > >suitability. I have also worked out a temporary clamping system to hold > >the panels in place while the tape and sealant cure. That might be > >unnecessary but given the curve of the cabin I don't want to take a > >chance on that part. I have masked the boat around the edge of the > >acrylic and sanded the paint on the cabin side so that is flat , smooth > >but dulled (220 grit). Now all that is left is to attach the actual > >panels and frankly that is what worries me most. While online > >instructions suggest applying the tape and sealant to the panel and > >then apply the panel to the boat, my thinking is that because the cabin > >side is a compound curve I would be better to apply the tape and > >sealant to the cabin and then press the panel into place. > > > >Time matters. I don't have forever to apply the sealant and remove the > >tape cover before pressing the panel on and worse still, I only get one > >chance to get the panel in the exact location. There is really no room > >for error. I have "rehearsed" placing the panel with my wife but that > >was without any of the tape or sealant. The cabin side has a moulded in > >edge at both the bottom and the aft end that are very helpful guides > >but one still need to make sure from the moment of first touch that > >everything is aligned perfectly so that the rest will wrap into place > >exactly where it is supposed to be. My hope is that I can rest the > >bottom edge and aft corner against the little raised edge first and > >then wrap the piece up into place at the top. > > > >If anyone has any clever ideas about how I could make the process idiot > >proof I would be forever grateful. The idea of having to use a chisel > >and grinder to remove the misaligned panels has no appeal to me at this > >juncture. I think I will need a very good shot of Rummy's Mont Gay > >medicine to calm my nerves first. > > > > > >Graham > >-------------- next part -------------- A non-text attachment was > >scrubbed... > >Name: Barbeque paint.jpg > >Type: image/jpeg > >Size: 178369 bytes > >Desc: not available > >Url : > >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/91 > >6312ae/attachment.jpg > > > >-------------- next part -------------- A non-text attachment was > >scrubbed... > >Name: Window flex test.jpg > >Type: image/jpeg > >Size: 52391 bytes > >Desc: not available > >Url : > >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/91 > >6312ae/attachment-0001.jpg > > > >-------------- next part -------------- A non-text attachment was > >scrubbed... > >Name: Window paint test.jpg > >Type: image/jpeg > >Size: 82200 bytes > >Desc: not available > >Url : > >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/91 > >6312ae/attachment-0002.jpg > > > >-------------- next part -------------- A non-text attachment was > >scrubbed... > >Name: Windows painted.jpg > >Type: image/jpeg > >Size: 54671 bytes > >Desc: not available > >Url : > >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150602/91 > >6312ae/attachment-0003.jpg > > > >__________________________________________________ > >To subscribe/unsubscribe go to > >http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > >For the list Charter and help with using the mailing list and archives > >go to http://www.rhodes22.org/list > >__________________________________________________ > > > > > >----- > >No virus found in this message. > >Checked by AVG - www.avg.com > >Version: 2015.0.5961 / Virus Database: 4355/9924 - Release Date: > >06/02/15 > >__________________________________________________ >To subscribe/unsubscribe go to >http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >For the list Charter and help with using the mailing list and archives go to >http://www.rhodes22.org/list >__________________________________________________ >-------------- next part -------------- >A non-text attachment was scrubbed... >Name: Windows with openings marked (2).jpg >Type: image/jpeg >Size: 173689 bytes >Desc: not available >Url : >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150603/51cc1373/attachment.jpg > >-------------- next part -------------- >A non-text attachment was scrubbed... >Name: Sailboat under cover Aug 08.jpg >Type: image/jpeg >Size: 242176 bytes >Desc: not available >Url : >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150603/51cc1373/attachment-0001.jpg > >-------------- next part -------------- >A non-text attachment was scrubbed... >Name: Paint for windows comparison.jpg >Type: image/jpeg >Size: 76907 bytes >Desc: not available >Url : >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150603/51cc1373/attachment-0002.jpg > >-------------- next part -------------- >A non-text attachment was scrubbed... >Name: Paint and peal test.jpg >Type: image/jpeg >Size: 210408 bytes >Desc: not available >Url : >http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20150603/51cc1373/attachment-0003.jpg > >__________________________________________________ >To subscribe/unsubscribe go to >http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >For the list Charter and help with using the mailing list and >archives go to http://www.rhodes22.org/list >__________________________________________________ > > >----- >No virus found in this message. >Checked by AVG - www.avg.com >Version: 2015.0.5961 / Virus Database: 4355/9933 - Release Date: 06/03/15
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 