2015-06-21; 14:02:40 EDT
Member Since
2014-05-06
Posts: 3821
Hi Susan, Sounds like you're in good hands a lot closer than I am. Good luck Your thread got so tangled up with other threads it doesn't appear separately on the nabble site and I missed the action for a while. Maybe someone can explain how that happens. Here's info I gathered from this site that might help with IMF foil removal. *********************************************** Oct 12, 2011; 4:24pm Charles Nieman Let me see if I can do this, everyone, please feel free to amplify or edit. I don’t think I have ever seen a step by step and I am going by memory. After the mast is down; 1. Remove the pop-top car from the mast. Take pictures - and replace it (in Correct orientation) before raising mast. 2. Remove the boom attachment from the furling assembly. This should involve a couple screws, plus pulling the furling line out of the boom and the out haul from the boom and main sail. 3. Slide the furling tube and main out of the mast (best to have two sets of hands as the tube gets pretty long and heavy if you try to hold from one end) 4. Remove the bottom bearing and the bottom donut. Check these parts for wear/condition. from the furling tube. Take pictures before doing this. See notes at bottom - some removed top stuff instead. Also see notes on checking set screws at top and using thread locker. 5. Remove the furling line from the furling tube - count the turns!! (this is usually attached by inserting through a hole in the tube and a knot tied on the inside of the tube). Take pictures. Good instructions. I would add that it is important to count the wraps on the outhaul and furling lines. When reinstalling, be sure to extend the sail all the way out to make sure you have the wraps correct before raising the mast. Adding wraps with the mast up is a real PITA. Rummy 6. Remove the remaining bottom donut (the donut at the top of the furling tube should not need to be removed). 7. Unroll the main sail. 8. Some main Some sails are attached to the furling tube vie a groove in the furling tube and others have a sleeve in the luff of the sail and then attached with a screw at the head and tack. It should be pretty obvious which you have and how to remove the sail. 9. To install new main sail, do these steps in reverse. A special note; don’t forget to reinstall the pop top car (in the correct orientation) prior to raising the mast. This is easy to forget, don’t ask me how I know. Charles98 Rhodes 22 /)~~~~~~~~~~~~~~~~ Oct 14, 2011; 11:50am R22RumRunner Good instructions. I would add that it is important to count the wraps on the outhaul and furling lines. When reinstalling, be sure to extend the sail all the way out to make sure you have the wraps correct before raising the mast. Adding wraps with the mast up is a real PITA. Rummy Mar 26, 2012; 12:26pm Basso I got to the point of having the tube out of the mast, but then I got confused as to why you would remove all the stuff at the base rather than removing the donut at the top? My attachment is with the screws at the head and tack. I then decided rather than mess with the stuff at the bottom to just remove the donut at the top. I have to get the sailrepaired (or hopefully not purchase a new one) before putting humpty dumpty back together. Am I in for any issues from removing the top donut rather than the whole attachment at the bottom? John B in WI. Mar 26, 2012; 2:08pm Charles Nieman I don't think there would be an issue. I had no choice. The top donut would not come off but the bottom ones were very loose. The only other point I can think of would be to repair or replace the donuts and or bearings at the bottom (which I had to do) or to replace the furling line (it is afterall just a piece of rope and won't last forever) but if all that is in good shape; then I agree to remove from the top. Any thoughts from the rest of the list?????? Mar 26, 2012; 2:59pm Chris Geankoplis-2 Regarding the IMF: One word of caution on the upper donut I had one of the set screws work loose and it would jamb if the boat wasn't on exactly even keel, a real pain in the ass. When you reset the screw, put a drop of silicone seal to keep it from backing out. It actually is not a bad idea on all the screws in the system. The advantage of this system is that all the parts can be fabricated at home using a few tools and readily available materials, especially if you do not have access to Stan. Chris G. ----- Brooks Bridges 1986, Recycled 2006 "Changes" Cambridge, MD -- View this message in context: http://rhodes-22.1065344.n5.nabble.com/IMF-Problem-Susan-new-tp50315.html Sent from the Rhodes 22 mailing list archive at Nabble.com.See the original archive post