2015-06-22; 06:47:05 EDT
Member Since
2014-05-06
Posts: 3821
Thanks for the advice Brooks. I absolutely agree that it is good design for a replaceable part to break to protect what it's attached to. There was another factor in my choice of through bolting the deterioration of the fiberglass around the holes where the step fit. However at this point it is all moot. You can raise from the bow with both the forward upper shrouds and the forward lower side stays attached, and they do keep the mast from going sideways beyond about 45 degrees. I've seen a few pix of gin poles in action, and that might be the solution for solo raising. Jefferson SV Patience '76 Lake Memphremagog, Quebec From: "thebooker [via Rhodes 22]" <ml-node+s1065344n50317h59 at n5.nabble.com> Date: Sun, 21 Jun 2015 11:56:32 -0700 (MST) To: User <jefferson at iteract.ca> Subject: Re: Your favorite way of pulling out mast step Jefferson, It may seem odd but, as others have pointed out, it can be GOOD design to design something to break if it's a lot easier to fix than what it's attached to. My Hobie trimaran just proved this for a second time (first was the break away rudder post that saved mangling the rudder). I was sailing from a beach, had raised CB, forgot to lower, couldn't figure out why I was blowing sideways towards rocks (grandson on board - distracting). Too late I noticed CB and left ama (float/whatever) hit rocks hard. The strut that held it out from main hull had a breakaway plastic bolt which broke - also a piece of something that kept strut from falling into water. It even had a spare bolted in nearby. Result, no damage and fix just required rebolting. R22 is my second "large" trailerable. Previous was a San Juan 21. San Juan had only two shrouds, an upper and a lower on each side that were even with the base of the mast in altitude and fore/aft. This meant could leave them attached and with no adjustment, raise/lower mast and they kept mast from going sideways through entire process. So, I built a gin pole out of a 2x4 and some plywood that you could plonk down on top of the mast at the base (could lock into mast and some bolts sticking out so base of gin pole held securely). Then I just pulled out jib halyard over top of gin pole (groove in top), hooked halyard to a new line running to bow stem where I installed a block that then routed this line back to cockpit and a winch. Making sure jib halyard securely cleated I wrapped around winch a few times and cranked away. Always worked perfectly - you literally couldn't screw up. I have to have fool proof things because I'm such a fool. When lowering, I could just put a few wraps on winch and control it with my hand. The line I used for this was less than 3/16 or smaller. Mast was a little lighter and no huge genoa to raise with it so job a bit easier admittedly. It's not raising/lowering the mast that's hard - any way to rig a gin pole as I did will do it. The trick is to mount gin pole base securely AND prevent mast going sideways during process. It sounds like you are using the boom as a gin pole and raising mast starting with mast on bow pulpit? The big problem I see is not having any control over mast going sideways. You must get this figured out or you WILL have repeat failures. The Rhodes shroud geometry is very different from SJ 21. Yours may be different from mine. Mine has a set of forward lowers and aft lowers that also attach to boat about 6 or 8 inches lower than base of mast. It also has a set running through spreaders roughly opposite mast but again attaching 6 or 8 inches lower than base of mast. I also don't know if you have the pop top. If you do and mast is set up so top is to rear of boat, you must have a mast holder at stern that sticks up 6 or 8 feet above top of stern, other wise base can't sit in mast step because of pop top. IF you have this set up you can use Stan's method of keeping mast from going sideways 1) have upper shrouds connected as they will be when mast is up - keep it from going side ways as mast nears verticle and 2) the forward lowers lengthened by about 8" of chain (should be tight with mast down). The forwards will then keep it from going sideways when mast is partway up. I know his system works raising from bow but here I'm totally ignorant. I don't expect this to be a recipe for your problems but hope the discussion of the geometry as I understand it may set off some light bulbs (LED ideally). Brooks Bridges 1986, Recycled 2006 "Changes" Cambridge, MD If you reply to this email, your message will be added to the discussion below: http://rhodes-22.1065344.n5.nabble.com/Your-favorite-way-of-pulling-out-mast -step-tp49974p50317.html To unsubscribe from Your favorite way of pulling out mast step, click here <http://rhodes-22.1065344.n5.nabble.com/template/NamlServlet.jtp?macro=unsub scribe_by_code&node=49974&code=amVmZmVyc29uQGl0ZXJhY3QuY2F8NDk5NzR8LTEyNjU5M zExODA=> . NAML <http://rhodes-22.1065344.n5.nabble.com/template/NamlServlet.jtp?macro=macro _viewer&id=instant_html%21nabble%3Aemail.naml&base=nabble.naml.namespaces.Ba sicNamespace-nabble.view.web.template.NabbleNamespace-nabble.view.web.templa te.NodeNamespace&breadcrumbs=notify_subscribers%21nabble%3Aemail.naml-instan t_emails%21nabble%3Aemail.naml-send_instant_email%21nabble%3Aemail.naml> -- View this message in context: http://rhodes-22.1065344.n5.nabble.com/Your-favorite-way-of-pulling-out-mast-step-tp49974p50326.html Sent from the Rhodes 22 mailing list archive at Nabble.com.See the original archive post