< prior
Back to Month
Go to Thread
2015-09-13; 14:52:49 EDT
Member Since
2014-05-06
Posts: 3821
Oh yea, Jerry Lowe S/V Country Rhodes '86See the original archive post
> Graham, > I really like the LEd's,I've changed all mine out several years ago, > really glad I did. Saturday before Labor Day,my grandsons and I watched > the fireworks from the boat and were one of the first boats back in the > slip.I'm on the end of the dock,which is great for sailing into the > slip,but on fireworks night , it leaves me exposed to the 40 or50 boats > that have to pass by me to get to their slip in the dark. So I left the > nav lights on, to be more visible,figuring I would be by Monday to turn > them off. Didn't happen. When I got there Thursday afternoon,the lights > we're still shining brightly. That would not be the case with the old > lights. > What I would suggest is change all the lights high up on the mast,( > anchor,steaming,deck lights) to LEd's, as they are the hardest ones to > get to when in a slip or on a moowing, and the first to go out,normally. > I would highly recommend new fixtures,not just bulbs, as the clips that > hold the bulbs corrode at the point of contact with the bulb, and in my > experience,way before the end of the season. > The rest of the lights , you may want to wait until you splash,and see > how much you use the other lights,and change them out as you see fit. > As for the tri color mast head light, I think it would depend on the area > you plan to sail in. For big water, bays,Great Lakes,ocean, I think the > mast head may get you seen better. Smaller lakes and maybe rivers,it might > be best for lights to be lower. > One thing to think about is that LEd's are diodes,and you can control two > lights with two wires by reversing the polarity. HOWEVER,the lights have > to be made for this application. A question to ask before you buy! > Also,you can't run both lights at the same time, so you will need to > arrange them like steaming/ anchor or deck / steaming or anchor / windex, > you get he idea. > One thing for sure,I have the brightest lights in the marina!, > > > > am wondering how newer Rhodes are equipped with navigation lights or if >> anyone has any strong preferences for lights. My 76 had the red and >> green >> lights mounted on the cabin sides back at the cockpit rather than near >> the >> bow. Is that still the case or have they been moved forward to the bow? >> Has >> anyone installed a masthead tricolor light? LED lights seem sensible but >> are >> they worth the added expense? Any recommendations would be welcome. >> >> >> Graham Stewart >> Agile. R22, 1976 >> Kingston Ontario Canada >> >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: September 12, 2015 6:32 PM >> To: 'The Rhodes 22 Email List' >> Subject: Re: [Rhodes22-list] Bilge ventilation >> >> Larry: >> I used white oak and epoxy when I rebuilt my 20' mahogany runabout to >> replace rotted ribs and bottom. White oak is resistant to rot but not >> impervious as the original wood ribs were white oak as well and >> eventually >> rotted albeit over a 40 year period. The big advantage using white oak >> is >> that it is amazing wood to steam bend. It is hard as rock when dry but >> after >> steaming for a while thin strips can be bent by hand easily. That makes >> it >> perfect for steam-bent ribs. >> >> Hopefully the epoxy will prohibit rot that only works if the epoxy >> totally >> encapsulates the wood with no cuts gouges or holes in the wood. In my >> case >> the epoxy also bonded the ribs to mahogany ply that was used to cold >> mold >> the new bottom. That combination made for an incredibly strong, solid, >> dry >> and relatively light boat. >> >> For the Rhodes floor, however, white oak is expensive and I would be >> inclined to use something that did not depend on the epoxy to be >> perfectly >> sealed. Pressure treated seems like the easiest, cheapest and most >> certain >> material to use. I will still use epoxy to bond it in place. Before I >> bought >> my Rhodes the previous owner rebuilt the floor structure using pressure >> treated fence boards. They lasted for more than 20 years with no sign of >> rot. The problem with using fence boats is that they are only .5 inch >> thick >> and that did not give a sufficiently wide edge for the floor boards to >> be >> screwed down. I was also unhappy with where they were located so I tore >> it >> all out to be replaced with thicker stock. I will no doubt be kicking >> myself >> for that as tearing things out is so much easier than putting it all >> back >> in >> - a realization that weighs more heavily as I consider that it was not >> really necessary except to feed my obsessive nature. >> >> >> Graham Stewart >> Agile. R22, 1976 >> Kingston Ontario Canada >> >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: September 12, 2015 1:47 PM >> To: 'The Rhodes 22 Email List' >> Subject: Re: [Rhodes22-list] Bilge ventilation >> >> When we rebuilt the floor and stringers, we used White Oak stringers and >> expoxied them. >> >> Larry Allen >> Makai >> Sarasota >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: Saturday, September 12, 2015 11:11 AM >> To: 'The Rhodes 22 Email List' >> Subject: Re: [Rhodes22-list] Bilge ventilation >> >> Bob: >> >> Best and crucial solution is to stop the leaks. I have gone to >> ridiculous >> lengths to do that by glassing the hull-heck joint and installing full >> acrylic window coverings to replace all ports. >> >> I am not sure that ventilation alone would preclude rot over time if the >> bilge is not dry otherwise. I plan to rebuild the floor and stringers >> with >> rot resistant materials - I will probably use pressure treated pine for >> the >> structural pieces. That said, ventilation still serves a purpose in >> terms >> of >> mold and mildew etc. >> >> I have installed a solar vent that should keep air moving in the boat. >> The >> bilge is hardly air tight at the best of time and, so long as water is >> not >> getting in, good cabin ventilation should be sufficient to move air >> through >> the bilge. For long periods and during the winter when the solar vent >> may >> not be operating I will leave the floor access panels open. >> >> >> >> Graham Stewart >> Agile. R22, 1976 >> Kingston Ontario Canada >> >> >> >> >> -----Original Message----- >> From: rhodes22-list-bounces at rhodes22.org >> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 >> Email >> List >> Sent: September 11, 2015 7:54 PM >> To: The Rhodes 22 Email List >> Subject: [Rhodes22-list] Bilge ventilation >> >> Has anyone installed vent holes or even active ventilation under the >> floor >> to prevent the stringers and floor from rotting out? >> >> Bob (palatka) >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go >> to >> http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go >> to >> http://www.rhodes22.org/list >> __________________________________________________ >> >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go >> to >> http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go >> to >> http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives >> go >> to http://www.rhodes22.org/list >> __________________________________________________ >> > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 