< prior
Back to Month
Go to Thread
2016-02-21; 14:14:52 EST
Member Since
2014-05-06
Posts: 3821
Thanks for the epoxy advice. I haven't done any fiberglass work either...yet. Are there less expensive alternatives to West Marine that work well enough? I see home depot has some 3m resin and some filler. Alex, I believe you are right about the trailer. If the boat is further back the centerboard will stay on a rubber roller and not swing down to hit the axle. However, I do believe I need to get it forward to get the tongue weight right. I have some number on that from weighing boat and trailer. I will publish those in a separate post after I locate them.See the original archive post
On Sat, Feb 20, 2016 at 10:21 PM, The Rhodes 22 Email List < rhodes22-list at rhodes22.org> wrote: > Or a turkey baster modified with a plunger. > > Larry > Sarasota > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: Saturday, February 20, 2016 8:29 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Tex on Centerboard > > Patrick: > > I don't think a syringe that a veterinarian would use would be sufficient > unless he treats elephants. I also expect that a sterile syringe would be a > bit pricy. I got my syringes at an automotive store. It is used for > measuring and dispensing oil. They work great as they are large enough to > pack a reasonable amount of thickened epoxy into the top where the plunger > goes. The thickened epoxy is too viscous to draw up into the cartridge with > the plunger. The tip can be cut to fit the hole snugly. > > If these aren't available I have also found "flavour injectors" in the > kitchen section of my local dollar store but in that case they come with a > needle point which is too fine for thickened epoxy mix but work ok for > unthickened epoxy. However, you can take the needle off and just use the > cartridge. I have attached pictures of what I use. > Graham > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: February 19, 2016 5:00 PM > To: rhodes22-list at rhodes22.org > Subject: Re: [Rhodes22-list] Tex on Centerboard > > Patrick > Another consideration. Do you have one of Stan's custom made drive on > trailers? When Tivo (Stan's man) delivered my boat he cautioned me not to > pull it too far forward on the trailer to avoid damaging the centerboard. > The bow stop is adjustable, and got moved around while the trailer was in > storage. Being cautious I didn't load far enough forward when I pulled out > for winter layup. Woops. Insufficient tongue weight. When Tivo > came > back last fall to install a forgotten Bimini, he told me the back of the > deck house and grab rail should be about even with a single axle. The > first photo was when the pros loaded it. The second with the building in > back was my bad reloading when the marina closed for the season. Stan, can > you back me up on this?? > I'll defer to Graham on the repair, but have filled hull / cockpit deck > voids in the same manner on my old boat. Your local veterinary clinic can > help you out with the big syringes. > Alex Cole DVMUrbana OHSV Lark > > > > > > > > Date: Thu, 18 Feb 2016 11:32:14 -0700 > > From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > Subject: [Rhodes22-list] Marine Tex on Centerboard > > To: "rhodes22-list at rhodes22.org" <rhodes22-list at rhodes22.org> > > Message-ID: > > <CAJGJx+Cr_0ERnqogO= > aqOyTi3uk0YBNLWyNkqMjQyqMpVtsdDw at mail.gmail.com> > > Content-Type: text/plain; charset="utf-8" > > > > Attached (hopefully) are a couple of pictures of the forward edge of > > my centerboard. This damage has come from banging into the trailer > > axle I guess. I would like to try to repair with Marine Tex, which I > > have never used. Any advice? Maybe after cleaning up the area I > > should drill a few holes and insert toothpicks or SS screws to give > > the Tex something to hold on to? > > > > -- > > Patrick Riley > > Lakewood, CO > > S/V Cleone > > -------------- next part -------------- > > > Message: 6 > > Date: Thu, 18 Feb 2016 15:40:00 -0500 > > From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > Subject: Re: [Rhodes22-list] Marine Tex on Centerboard > > To: "'The Rhodes 22 Email List'" <rhodes22-list at rhodes22.org> > > Message-ID: <00ba01d16a8c$8a16f0e0$9e44d2a0$@ca> > > Content-Type: text/plain; charset="us-ascii" > > > > Patrick: > > > > >From the picture I suspect that the damage was caused by more than > > >just > > hitting the trailer. I suspect that the board was structurally weak > > due to large voids inside which may have filled with water. If you > > have a cold climate where you are the water would do a lot of damage > > as it > freezes. > > Tapping the board with something hard should tell you if there are > > other voids and if so, I would definitely fix those first. > > > > I had this problem with my rudder and centreboard. The fix that I used > > for the voids was fairly simple. I drilled holes wherever I suspected > > there might be a void. It is best to have more than one hole in each > > void so that when you eject epoxy into one hole the air can escape > > from the other. If you see any sign of moisture I would wait some time > > to allow the moisture to evaporate from inside the board before > > filling it > with epoxy. > > > > I used a big syringe with a plastic 1/4" tip to pump unthickened epoxy > > into each hole until it came out the neighbouring holes. It is best to > > drill holes that fit the tip of the syringe tightly so you can build a > > bit of pressure to push the epoxy in. You will need to top it up > > several times as the epoxy finds its way down into the board. Once it > > won't take any more, let the epoxy set until it is no longer fluid and > > then flip the board over and do the same on the other side. When I did > > mine I was really surprised how much epoxy I was able to pump into the > > core. I am sure I injected more than a quart. I did the same with my > > centreboard housing and it took 3 GALLONS to fill the voids. > > > > As for the damaged cavity, I would clean out the cavity, make sure it > > is dry, coat the cavity with epoxy and then and fill it in with layers > > of epoxy thickened with high-strength adhesive filler. Epoxy can > > generate a lot of heat as it cures so build the cavity in layers > > (about 1") but addg each layer as soon as it starts to cool. At this > > point the previous layer will stop being tacky but still soft enough > > to > scratch it with your fingernail. > > If you wait until it cures completely, you should grind a coarse > > surface on the old to provide for a mechanical bond. > > > > Using pins is unnecessary. Toothpicks would be useless. Properly > > thickened epoxy will keep its form without support. Make the batch to > > the consistency of peanut butter. > > > > Use fairing filler for the final few layers as it is MUCH easier to sand. > > Try to make the two sides of the board as similar as you can. > > > > I would also be tempted to cover it all with fibreglass as there may > > be fine crals where water could migrate. Finally, I would coat the > > whole rudder with at least four coats of regular epoxy. You can apply > > the coats as soon as the epoxy will hold properly to the previous coat > > - > about 20 minutes. > > > > This is a bit of a nuisance but not difficult to do. > > > > Grahame > > > > Graham Stewart > > Agile. R22, 1976 > > Kingston Ontario Canada > > > > > > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Rhodes on delivery.jpg > Type: image/jpeg > Size: 8711 bytes > Desc: not available > Url : > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160219/90d7b3e > 1/attachment.jpg > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Poor trailer placement.jpg > Type: image/jpeg > Size: 9243 bytes > Desc: not available > Url : > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160219/90d7b3e > 1/attachment-0001.jpg > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: 2016-02-20 20.13.20.jpg > Type: image/jpeg > Size: 53729 bytes > Desc: not available > Url : > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160220/5ee1c56 > 6/attachment.jpg > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: 2016-02-20 20.14.25.jpg > Type: image/jpeg > Size: 93803 bytes > Desc: not available > Url : > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160220/5ee1c56 > 6/attachment-0001.jpg > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ > -- Patrick Riley Lakewood, CO S/V Cleone
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 