< prior
Back to Month
Go to Thread
2016-02-22; 15:48:51 EST
Member Since
2014-05-06
Posts: 3821
Thank you. The product I saw at Home Depot was indeed polyester. PatrickSee the original archive post
On Mon, Feb 22, 2016 at 6:47 AM, The Rhodes 22 Email List < rhodes22-list at rhodes22.org> wrote: > Alex: > > Don't confuse epoxy resin with polyester resin. The latter is much cheaper > and has very different attributes. The application methods also differ. > Epoxy is much stronger, durable and water resistant and is far superior for > repairs such as you plan on your centreboard. > > Your boat, like all boats, are made with polyester resin - because of its > cost and fast curing. Epoxy adheres to polyester but polyester does not > adhere well to epoxy so you would not use epoxy if for any reason you > wanted > to cover it with polyester as might occur if you are also wanting to do > some > gel coat repairs. Gel coat is polyester > > For a repair such as the one you are considering I would not try to save by > using polyester. > > Graham > > -----Original Message----- > From: rhodes22-list-bounces at rhodes22.org > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > Email > List > Sent: February 21, 2016 2:15 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Tex on Centerboard > > Thanks for the epoxy advice. I haven't done any fiberglass work > either...yet. Are there less expensive alternatives to West Marine that > work well enough? I see home depot has some 3m resin and some filler. > > Alex, > I believe you are right about the trailer. If the boat is further back the > centerboard will stay on a rubber roller and not swing down to hit the > axle. > However, I do believe I need to get it forward to get the tongue weight > right. I have some number on that from weighing boat and trailer. > I will publish those in a separate post after I locate them. > > > On Sat, Feb 20, 2016 at 10:21 PM, The Rhodes 22 Email List < > rhodes22-list at rhodes22.org> wrote: > > > Or a turkey baster modified with a plunger. > > > > Larry > > Sarasota > > > > -----Original Message----- > > From: rhodes22-list-bounces at rhodes22.org > > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > > Email List > > Sent: Saturday, February 20, 2016 8:29 PM > > To: 'The Rhodes 22 Email List' > > Subject: Re: [Rhodes22-list] Tex on Centerboard > > > > Patrick: > > > > I don't think a syringe that a veterinarian would use would be > > sufficient unless he treats elephants. I also expect that a sterile > > syringe would be a bit pricy. I got my syringes at an automotive > > store. It is used for measuring and dispensing oil. They work great as > > they are large enough to pack a reasonable amount of thickened epoxy > > into the top where the plunger goes. The thickened epoxy is too > > viscous to draw up into the cartridge with the plunger. The tip can be > cut > to fit the hole snugly. > > > > If these aren't available I have also found "flavour injectors" in the > > kitchen section of my local dollar store but in that case they come > > with a needle point which is too fine for thickened epoxy mix but work > > ok for unthickened epoxy. However, you can take the needle off and > > just use the cartridge. I have attached pictures of what I use. > > Graham > > > > -----Original Message----- > > From: rhodes22-list-bounces at rhodes22.org > > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 > > Email List > > Sent: February 19, 2016 5:00 PM > > To: rhodes22-list at rhodes22.org > > Subject: Re: [Rhodes22-list] Tex on Centerboard > > > > Patrick > > Another consideration. Do you have one of Stan's custom made drive on > > trailers? When Tivo (Stan's man) delivered my boat he cautioned me not > to > > pull it too far forward on the trailer to avoid damaging the centerboard. > > The bow stop is adjustable, and got moved around while the trailer was > > in storage. Being cautious I didn't load far enough forward when I > pulled > out > > for winter layup. Woops. Insufficient tongue weight. When Tivo > > came > > back last fall to install a forgotten Bimini, he told me the back of the > > deck house and grab rail should be about even with a single axle. The > > first photo was when the pros loaded it. The second with the building > in > > back was my bad reloading when the marina closed for the season. > > Stan, can you back me up on this?? > > I'll defer to Graham on the repair, but have filled hull / cockpit deck > > voids in the same manner on my old boat. Your local veterinary clinic > can > > help you out with the big syringes. > > Alex Cole DVMUrbana OHSV Lark > > > > > > > > > > > > > > > Date: Thu, 18 Feb 2016 11:32:14 -0700 > > > From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > > Subject: [Rhodes22-list] Marine Tex on Centerboard > > > To: "rhodes22-list at rhodes22.org" <rhodes22-list at rhodes22.org> > > > Message-ID: > > > <CAJGJx+Cr_0ERnqogO= > > aqOyTi3uk0YBNLWyNkqMjQyqMpVtsdDw at mail.gmail.com> > > > Content-Type: text/plain; charset="utf-8" > > > > > > Attached (hopefully) are a couple of pictures of the forward edge of > > > my centerboard. This damage has come from banging into the trailer > > > axle I guess. I would like to try to repair with Marine Tex, which > > > I have never used. Any advice? Maybe after cleaning up the area I > > > should drill a few holes and insert toothpicks or SS screws to give > > > the Tex something to hold on to? > > > > > > -- > > > Patrick Riley > > > Lakewood, CO > > > S/V Cleone > > > -------------- next part -------------- > > > > > Message: 6 > > > Date: Thu, 18 Feb 2016 15:40:00 -0500 > > > From: The Rhodes 22 Email List <rhodes22-list at rhodes22.org> > > > Subject: Re: [Rhodes22-list] Marine Tex on Centerboard > > > To: "'The Rhodes 22 Email List'" <rhodes22-list at rhodes22.org> > > > Message-ID: <00ba01d16a8c$8a16f0e0$9e44d2a0$@ca> > > > Content-Type: text/plain; charset="us-ascii" > > > > > > Patrick: > > > > > > >From the picture I suspect that the damage was caused by more than > > > >just > > > hitting the trailer. I suspect that the board was structurally weak > > > due to large voids inside which may have filled with water. If you > > > have a cold climate where you are the water would do a lot of damage > > > as it > > freezes. > > > Tapping the board with something hard should tell you if there are > > > other voids and if so, I would definitely fix those first. > > > > > > I had this problem with my rudder and centreboard. The fix that I > > > used for the voids was fairly simple. I drilled holes wherever I > > > suspected there might be a void. It is best to have more than one > > > hole in each void so that when you eject epoxy into one hole the air > > > can escape from the other. If you see any sign of moisture I would > > > wait some time to allow the moisture to evaporate from inside the > > > board before filling it > > with epoxy. > > > > > > I used a big syringe with a plastic 1/4" tip to pump unthickened > > > epoxy into each hole until it came out the neighbouring holes. It is > > > best to drill holes that fit the tip of the syringe tightly so you > > > can build a bit of pressure to push the epoxy in. You will need to > > > top it up several times as the epoxy finds its way down into the > > > board. Once it won't take any more, let the epoxy set until it is no > > > longer fluid and then flip the board over and do the same on the > > > other side. When I did mine I was really surprised how much epoxy I > > > was able to pump into the core. I am sure I injected more than a > > > quart. I did the same with my centreboard housing and it took 3 GALLONS > to fill the voids. > > > > > > As for the damaged cavity, I would clean out the cavity, make sure > > > it is dry, coat the cavity with epoxy and then and fill it in with > > > layers of epoxy thickened with high-strength adhesive filler. Epoxy > > > can generate a lot of heat as it cures so build the cavity in layers > > > (about 1") but addg each layer as soon as it starts to cool. At this > > > point the previous layer will stop being tacky but still soft enough > > > to > > scratch it with your fingernail. > > > If you wait until it cures completely, you should grind a coarse > > > surface on the old to provide for a mechanical bond. > > > > > > Using pins is unnecessary. Toothpicks would be useless. Properly > > > thickened epoxy will keep its form without support. Make the batch > > > to the consistency of peanut butter. > > > > > > Use fairing filler for the final few layers as it is MUCH easier to > sand. > > > Try to make the two sides of the board as similar as you can. > > > > > > I would also be tempted to cover it all with fibreglass as there may > > > be fine crals where water could migrate. Finally, I would coat the > > > whole rudder with at least four coats of regular epoxy. You can > > > apply the coats as soon as the epoxy will hold properly to the > > > previous coat > > > - > > about 20 minutes. > > > > > > This is a bit of a nuisance but not difficult to do. > > > > > > Grahame > > > > > > Graham Stewart > > > Agile. R22, 1976 > > > Kingston Ontario Canada > > > > > > > > > > > > > -------------- next part -------------- A non-text attachment was > > scrubbed... > > Name: Rhodes on delivery.jpg > > Type: image/jpeg > > Size: 8711 bytes > > Desc: not available > > Url : > > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160219/9 > > 0d7b3e > > 1/attachment.jpg > > -------------- next part -------------- A non-text attachment was > > scrubbed... > > Name: Poor trailer placement.jpg > > Type: image/jpeg > > Size: 9243 bytes > > Desc: not available > > Url : > > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160219/9 > > 0d7b3e > > 1/attachment-0001.jpg > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > __________________________________________________ > > -------------- next part -------------- A non-text attachment was > > scrubbed... > > Name: 2016-02-20 20.13.20.jpg > > Type: image/jpeg > > Size: 53729 bytes > > Desc: not available > > Url : > > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160220/5 > > ee1c56 > > 6/attachment.jpg > > -------------- next part -------------- A non-text attachment was > > scrubbed... > > Name: 2016-02-20 20.14.25.jpg > > Type: image/jpeg > > Size: 93803 bytes > > Desc: not available > > Url : > > > > http://www.rhodes22.org/pipermail/rhodes22-list/attachments/20160220/5 > > ee1c56 > > 6/attachment-0001.jpg > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > __________________________________________________ > > > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > __________________________________________________ > > > > > > -- > Patrick Riley > Lakewood, CO > S/V Cleone > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ > -- Patrick Riley Lakewood, CO S/V Cleone
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 