< prior
Back to Month
Go to Thread
2016-08-24; 22:43:23 EDT
Member Since
2004-04-05
Posts: 2062
Bob,
Why do I have a picture of you as Atlas?
Chris G
See the original archive post
On Sun, Aug 21, 2016 at 9:29 PM, Goodness <spreadgoodnews at gmail.com> wrote: > Graham: Being the foolish and impatient type, i used my back, stood up > under the top pressing my back into it and put a 4x4 post with a cloth over > the top under it to support then tapped the compression post and bulkhead > in place with a mallet. Then i tapped out the 4x4 and the compression post > was firmly in place. Right or wrong, I didnt give it 2 minutes of though! > I was certain i had the base at the right height as i had made templates > before i deconstructed the rotten base. I just assumed the wide span of > the fiberglass head liner was heavy and sagged. My deck always remained > rock solid. > Bob (palatka) > > On Aug 21, 2016, at 9:08 AM, Graham Stewart <gstewart8 at cogeco.ca> wrote: > > > > BoB: > > > > Thanks for the feedback. That is very helpful. > > Yes, I had unstepped the mast and there was no load on the deck - not > even > > snow. I made the new bulkhead pieces using the old ones as templates and > > placed them according to the fibreglass stubs that were in place to hold > the > > old pieces. Everything seems to be coming together properly so I am > pretty > > sure that the compression post base is in the correct place. The only > > difference is that the old base had been distorting under the force of > the > > compression post over the years so the new piece corrected for that > > accounting for perhaps as much as 1/2 inch in the drop of the cabin top. > > What did you use to raise the cabin top in order to reinsert the > compression > > post? How much force did it take? > > Thanks again, > > > > > > Graham Stewart > > Agile. R22, 1976 > > Kingston Ontario Canada > > > > > > > > > > -----Original Message----- > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf Of > > Goodness > > Sent: August 20, 2016 11:09 PM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] deck shape > > > > Graham: i assume that your mast has remained unstepped during your > > restoration. > > Remember you have an inner hull so your cabin top has two layers. The > center > > of my cabin top interior dropped an inch immediately upon removing my > > compression post. I had the floor bulkhead replaced within a week but > had > > to lift the inner lining up to get the compression post to fit back into > > place. It is nice and tight and the deck is level and firm. Fiberglass > is > > very flexible and strong. Make sure your base for the post is at the > proper > > height however. Do you have an original bulkehad as well? That helps > you > > guage that the compression post is in the right position. > > Good luck! > > > > Bob (palatka) > > > >> On Aug 20, 2016, at 7:25 PM, Graham Stewart <gstewart8 at cogeco.ca> > wrote: > >> > >> I am finally at the point in my restoration of Agile where am > >> installing the compression post and main bulkhead. However, it appears > >> that the cabin top has dropped by a full inch. I am left with the > >> choice of either jacking up the deck so that the compression post fits > >> or cutting the post back to fit the space. Does anyone know what the > >> implications might be if I gradually jack up the cabin top? Might I > >> crack the deck? Obviously I should have supported the cabin top when I > >> removed the post but I didn't think it would deform when there was no > load > > on it. > >> > >> If anyone has any suggestions I would appreciate it. Otherwise I will > >> try to rais the top very gradually and if that seems to require more > >> than a moderate force I will live with the missing inch and tell > >> myself that I am still growing. > >> > >> > >> Graham Stewart > >> Agile. R22, 1976 > >> Kingston Ontario Canada > >> > >> > >> > >> > >> > >> __________________________________________________ > >> To subscribe/unsubscribe go to > >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >> > >> For the list Charter and help with using the mailing list and archives > >> go to http://www.rhodes22.org/list > >> __________________________________________________ > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > go to > > http://www.rhodes22.org/list > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to http://www.rhodes22.org/ > mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > > __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/ > mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 